2009 SKODA SUPERB remote control

Unlocking and locking
51
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The transmitter with the battery is housed
in the handle of the remote control key.
The receiver is located in the interior of the car. The operating range of the remote control is approx. 30 m. But this range of the remote control can be reduced if the batteries are weak. The remote control key has a fold-open key
bit which can be used
for unlocking and
locking the car manually and also for starting the engine. If a lost key is replaced or if the rece
iver unit has been repaired or a new unit
installed, it is then necessary for an authorised Škoda Service Partner to initialise the system. Only after this is it possible to again use the remote control.
Note
•
The remote control is automatically deac
tivated when the ignition is switched
on.•
The operation of the remote control may temporarily be affected by interfer-
ence from transmitters close to the car
and which operate in the same frequency
range (e.g. mobile phon
e, TV transmitter).
•
The battery must be replaced, ideally by
an authorised Škoda Service Partner, if
the central locking or anti-theft alarm system does react to the remote control at less than 3 metres away.•
If the driver door is opened, the vehi
cle cannot be locked using the remote
control.
Unlocking and locking carUnlocking the vehicle

– Press button for about 1 second. Locking the vehicle

– Press button for about 1 second.Deactivating safe securing system – Press button twice in 3 seconds. Further information
⇒
page 46.
Small boot lid release

– Press button for about 1 second
⇒
fig. 48
. Further information
⇒
page 48.
Automatic raising of the small boot lid

– Press button for about 2 second
⇒
fig. 48
. Further information
⇒
page 48.
Folding out of the key –Press button .
Fig. 48 Remote control key
A1A3A2A2A2A4
s2dk.1.book Page 51 Wednesday, April 8, 2009 12:23 PM

Unlocking and locking
52
Folding up of the key – Press button and collapse the key bit in the housing.The turn signal lights flash twice as
confirmation that the vehicle has been
unlocked. The vehicle will lock again auto
matically if you unlock the vehicle using
button but do not open a door or the
boot lid within the next 30 seconds. This
function is intended to prevent the car being unlocked unintentionally. In addition, when the car is unlocked, the
power seats and exterior mirrors* move
into the position assigned to this key. The stored setting of driver seat and exterior mirrors is retrieved. When the vehicle is unlocked or locked, the interior lights and the lights of the entry area are automatically switched
on or off via the door contact.
Display of the locking The turn signal lights flash once to co
nfirm that the vehicle has been correctly
locked. If the doors or the boot lid remain open
after the vehicle has been locked, the turn
signal lights do not flash unt
il they have been closed.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti- vated, there must not be any person in the vehicle as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into
the vehicle in an emergency - hazard!
Note
•
Operate the radio remote control only wh
en the doors and boot lid are closed
and you have visual contact with the vehicle.•
Once in the car, you must not press the lock button
 of the radio remote
control before inserting the key into the ignition lock in order to avoid the car being inadvertently locked and, in addition, th
e anti-theft alarm system* being switched
on. Should this happen, press the unlock button
 of the radio remote control.
•
The automatic raising of the small boot
lid can be impaired at temperatures
below +4°C.Synchonisation of the remote controlIf the vehicle cannot be unlocked by actuatin
g the remote control system then it is
possible that the code in the key and the
control unit in the vehicle are no longer
synchronised. This can occur when the buttons on the radio-operated key are actu-ated a number of times outside of the operative range of the equipment or the battery on the remote control was replaced. This means it is necessary to
synchronise the code as follows:
•
Press any button on the remote control.
•
Pressing of the button means that the d
oor will unlock with the key within 1
minute
⇒page 47, “Emergency unlocking and locking of the driver's door”.
Anti-theft alarm system*DescriptionThe anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle. How is the alarm system activated? The anti-theft alarm system is activated wh
en the vehicle is locked with the key in
the driver's door or by us
ing the radio remote control
⇒page 47, “Emergency
unlocking and locking of the driver's door
”. The door contact monitoring is acti-
vated approx. 15 seconds after the locking. The interior and the towing protection monitoring are activated appr
ox. 30 seconds after the locking. If a door is opened
during activation, the monitoring is
only activated 5 se
conds after closing.
A4
A1
s2dk.1.book Page 52 Wednesday, April 8, 2009 12:23 PM

Unlocking and locking
53
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
How is the alarm system deactivated? The alarm system is deactivated by pressing the unlock button on the radio remote control. The vehicle is automatically locked again if the vehicle is not opened within 30 seconds after reactivating the anti-theft alarm system. The alarm system is also deactivated if you unlock the vehicle door using the key within 45 seconds after locking the vehicle. Once you unlock the vehicle by inserting the key into the driver door within 45 seconds, you then have to insert the key into the ignition lock and switch the igni- tion on within 15 seconds after unlocking th
e door in order to deactivate the alarm
system. The
alarm will be triggered
if you do
not switch on
the ignition within 15
seconds. When is the alarm triggered? The following security areas of the locked vehicle are monitored:•
Bonnet,
•
Boot lid,
•
Doors,
•
Ignition lock,
•
Socket of the factory-fitted towing device,
•
Angle of the vehicle*,
•
Vehicle interior*,
•
A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either
of the two battery terminals is discon-
nected while the anti-theft alarm system is activated. How is the alarm switched off? You switch the alarm off if you unlock the
car with the radio remote control in the
key or if you switch the ignition on.
Note
•
The working life of the alarm siren is 6 years. More detailed information is avail-
able by a specialist garage.
•
Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm system is fully operational.•
Coding of the radio remote control and
the receptor part precludes the use of
the radio remote control from other vehicles.Interior monitor and towing protection monitoring*

The interior monitor detects movements inside the car and then trig- gers the alarm.Switch off the interior monitor and towing protection monitoring – Switch off the ignition. – Open the driver door. – Press the button

at the centre column on the driver side
⇒
fig. 49
,
the symbol

which lights up in the button changes from red to
orange.
– Lock the vehicle within 30 seconds.The interior monitor and the towing protection monitoring are switched on again automatically the next ti
me the car is locked.
Fig. 49 Button for interior monitor and towing protec-tion monitoring
s2dk.1.book Page 53 Wednesday, April 8, 2009 12:23 PM

Unlocking and locking
56
Force limiter of the power windowsThe electrically operated power windows are fitted with a force limiter. It reduces the risk of bruises or injuries when closing the windows. If there is an obstacle, the closing proce
ss is stopped and the window goes down by
several centimeters. If the obstacle prevents the window from
being closed during the next 10 seconds,
the closing process is interrupted once ag
ain and the window go
e s d o w n b y s e v e ra l
centimeters. You must try to close the window once
again within 10 seconds after the window
has gone down twice, even if the obstacle
was not yet removed, the closing process
is stopped. During this time it is not possible to automatically close the window. The force limiter is still switched on. The force limiter is only switched off, if you attempt to close the window within the next 10 seconds -
the window closes now with full strength!
If you wait longer than 10 seconds, th
e force limiter is switched on again.
WARNING
You should take particular care when closing the windows! You may other- wis e su ffe r s ev e re inj uri e s a s a re sul t o f g e t tin g an a rm , fo r e xa m pl e, j am m e d in the window!Window convenience operationYou can open and close the electrically powered windows as follows when unlocking and locking the vehicle (j
ust closing of the sliding roof).
Opening a window•
by holding the pressed unlock button on the remote control,
•
by holding the pressed top part of the
button for the central locking system in
the driver door,
•
by holding the key in the driver's lock in the unlock position
⇒page 47, “Emer-
gency unlocking and lockin
g of the driver's door”.
Closing a window•
by holding the pressed lock button on the remote control,
•
by holding the pressed bottom part of
the button for the central locking system
in the driver door,•
by holding the key in the driver
's lock in the lock position
⇒page 47.
You can interrupt the opening or closing operation of the windows immediately by releasing the key or the lock button.
WARNING
The system is fitted with a force limiter
⇒page 56. If there is an obstacle, the
closing process is stopped and the wi
ndow goes down by several centime-
ters. You should then take particular care when closing the windows! You may otherwise suffer severe injuries as a result of getting an arm, for example, jammed in the window!
Note
The convenience opening of the windows with the aid of the key in the driver's lock is only possible within 45 seconds after deactivating or activating the alarm system.Operational faultsElectrically operated power windows do not operate If the battery has been disconnected an
d then reconnected while the window was
opened, the electrically operated power windows do not operate. The system must be activated. Proceed as follows in
order to re-establish the function:
•
you can close the window
by pulling the respective switch on the top edge
•
release the switch
s2dk.1.book Page 56 Wednesday, April 8, 2009 12:23 PM

Unlocking and locking
58
ClosingSliding closed/closing the sliding/tilting roof – Turn the switch to position
⇒
fig. 52
.
Safety closing The sliding/tilting roof is equipped with an overload protection system. If an obstacle (e.g. ice) prevents closing,
the sliding/tilting roof stops and opens
completely. You can close the sliding/tilting roof completely without overload protection by pressing the
switch to the position
⇒page 57, fig. 52
at the front
for as long as it takes for the sliding/tilting roof to shut completely
⇒
.
WARNING
Close the sliding/tilting roof carefully - risk of injury!Convenience operationYou can also close an open sliding/tilting roof from the outside. – Keep the lock button on the radio remote control pressed or hold the
key in the lock of the driver's do
or in the lock position until the
sliding/tilting roof is closed
⇒
.
The closing operation stops when one releases the key or the lock button.
WARNING
Close the sliding/tilting roof carefully - risk of injury! The overload protec- tion system does not function with the convenience closing.
Electric sliding/tilting roof with solar cells*If there is sufficient bright sunlight, the solar cells on the sliding/tilting roof deliver power for the fresh air blower. Further information
⇒page 109.
The operation of the sliding/tilting roof with solar cells is the same as of a normal sliding/tilting roof.Emergency operationYou can close and/or open the sliding/tilting roof by hand if the system is defect.
AA
AA
Fig. 53 Detail of the head- liner: point for positioning screwdriverFig. 54 Detail of the head-liner: Emergency operation
s2dk.1.book Page 58 Wednesday, April 8, 2009 12:23 PM

Lights and Visibility
63
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
You can change the illumination period
for the Coming Home Function by
means of the information display*.Leaving Home FunctionThis function makes it possible to switch on the lights when approaching the vehicle. Switching on Leaving Home Function – Unlock the vehicle with the radio remote control - the lights come on.Depending on equipment fitted the function Leaving Home switches on the following lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Leaving Home Function The function Leaving Home is controlled wi
th the light sensor in the mount of the
interior rear mirror. If the light intensity is higher than the set value of the light sensor, the Leaving Home Function is not
switched on after unlocking the vehicle
with the radio remote control. After unlocking the vehicle with the radio remote control, the lights come on for 30 seconds. The Leaving Home Function is also switched off after the ignition is switched on and after locking the vehicle. If no door is opened within
30 seconds, the lights go out and the vehicle is locked
automatically.
Note
•
If the Leaving Home Function is switch
ed on constantly, the battery will be
heavily discharged particular
ly in short-haul traffic.
•
The switching on of the described lights
should only be und
ertaken in accord-
ance with the legal requirements.•
You can change the illumination period
for the Leaving Home Function by
means of the information display*.Adaptive headlights (AHL)*Switch on Adaptive headlights (AHL)* – Turn the light switch
⇒
page 61, fig. 56
into position

.
The outer illumination switches on if:•
the light sensor recognizes the low light intensity,
•
no reverse gear is engaged,
•
the operation “tourist light” is not switched on.
The light sensor switches on the full ou
ter illumination at low light intensity.
System AHL* makes it possible to change
the length and width of illumination of
the headlight. The length and width of i
llumination changes automatically in rela-
tion to the vehicle speed and the use of the windscreen wiper. System AHL* operates in the following modes. Mode out of town The mode “out of town” is a basic mode. The dispersion of the cone of light in front of the vehicle is similar to the low beam. The mode is active if none of the following modes are active. Mode rain In the mode “rain” the dispersion of the cone of light in front of the vehicle is wider and the width of illumination is shorter,
so that during bad weather (rain) the
dazzling of the oncoming drivers can be reduced. The mode is activated at speeds of 15 - 70 km/h and if the windscreen wi
pers continuously operate for a period of
time longer than 2 minutes. The mode
is deactivated when dropping below or
exceeding the set speed limit or if the windscreen wipers have been switched off for a period of time longer than 8 minutes.
s2dk.1.book Page 63 Wednesday, April 8, 2009 12:23 PM

Lights and Visibility
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Lowerable exterior mirror* with the aid of the key for remote control – If all the windows are closed, press the unlock button on the radio
remote control
⇒
page 51, fig. 48
for approx. 2 seconds.
Tilting surface of front passenger exterior mirror* When the rotary knob is in position
 ⇒page 76, fig. 76
and the reverse gear is
engaged, the surface of the mirror tilts down slightly. This provides an aid in seeing the kerb of the pavement when parking the car. The mirror returns into its initial position,
after the rotary knob is moved out of the
position
 and put into another position or if the speed is more than 15 km/h.
Memory for exterior mirrors* On vehicles fitted with a memory for the driver seat, the relevant setting of the exte- rior mirror is also stored automatica
lly when the seat position is stored.
WARNING
•
Convex (curved outward) or spherical (differently curved) exterior
mirrors increase the vision field. They do, however, make objects appear smaller in the mirror. These mirrors are only of limited use, therefore, for estimating distances to the following vehicles.•
Use whenever possible the interior rear mirror, for estimating the
distances to the following vehicles.
Note
•
Do not touch the surfaces of the exterior mirrors if the exterior mirror heater is
switched on.•
You can set the exterior mirrors by hand, if
the power setting function fails at any
time by pressing on the edge of the mirror surface.•
Contact your specialist garage if a fault exists with the power setting of the exte-
rior mirrors.
Automatic dimming exterior mirror*The exterior mirrors are dimmed together with the interior mirror. If the automatic dimming is switched on, the mirror dims
automatically
depending on the light
striking the mirror from the rear. When the interior lights are switched on or the reverse gear is engaged, the mirror always moves back into the
basic position (not dimmed).
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window is not in use or the light striking th
e rear of the interior rear-view mirror is
not affected by other objects.•
Do not affix any stickers in front of the li
ght sensor, so that you do not impair the
automatic dimming function or put it out of operation.•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming
is switched off.
A3
s2dk.1.book Page 77 Wednesday, April 8, 2009 12:23 PM

Seats and Stowage
81
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Engage reverse gear. – Move the right exterior mirror into the desired position
⇒
page 76.
– Take the vehicle out of gear. The set position of the exterior mirror is
stored.
Memory buttons Memory for the seat offers the possibility
to store the individual driver seat and
external mirror position. An individual posi
tion can be allocated to each of the three
memory buttons
⇒page 80, fig. 80
, that is three in tota
l. After pressing the
corresponding memory button , the seat and the exterior mirror are automati-cally moved into the positions which
have been allocated to this button
⇒page 81.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.
Note
•
For safety reasons, it is not possible to store this position if the inclination angle
of the seat backrest is more than 102° in relation to the seat cushion.•
When storing settings with the memory buttons, we recommend that you begin
with the front button and assign a memo
ry button to each additional driver.
•
Each new setting stored with the same
button erases the previous setting.
•
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual setting
of the exterior mirror on the passenger
side for reversing.Assigning remote control to the memory buttonsAfter storing the settings of the seat
and exterior mirrors, you have 10
seconds in order to assign the radio remote control to the appropriate memory button. – Withdraw the ignition key.
– Press the unlock button
⇒
page 51, after the successful assignment
an audible signal will sound. The setting is stored with the memory button which you have selected.
If you wish to be able to retrieve the settings which are stored in the memory by also using the radio remote control, you have
to assign the radio remote control to a
memory button in each case. If you wish, you can obtain an additional
remote control key from an authorised
Škoda Service partner and then assign th
e remote control key to another memory
button.
Note
•
If the radio remote control had previous
ly been assigned
to another memory
button, this setting is then erased by the new assignment.•
If you assign the radio remote control
to a memory button which has already
been assigned to a radio remote control,
the old assignment is also replaced by a
new assignment in this case.•
The assignment of the radio remote cont
rol to a memory button is retained,
however, after reassigning the seats and exterior mirrors.Retrieving settings of the seat and mirrors You can retrieve the stored settings either with the memory buttons or with the remote control*.Retrieving settings with memory buttons – In order to retrieve the stored setting, you have two possibilities: –
One-touch automatic memory:
Briefly press the desired memory
button
⇒
page 80, fig. 80
. The seat and exterior mirror are moved
automatically into the stored position
s (this applies only if the ignition
is switched on and the speed is less than 5 km/h).
AB
AB
AB
s2dk.1.book Page 81 Wednesday, April 8, 2009 12:23 PM