2009 SKODA SUPERB warning

Transporting children safely
187
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If this is not done, there is a risk of
the child suffering severe or even fatal
injuries if the front passenger airbag
is deployed. In certain countries
national legal provisions also requir
e that the side or head passenger
airbags be deactivated. When transporting a child on the front passenger seat, please comply with the appropri
ate national regulations regarding the
use of child safety seats.•
If the front passenger airbag has been
switched off by a specialist garage
using the vehicle system tester, the fr
ont side airbag and head passenger
airbag* remains switched on. In certai
n countries national legal provisions
require that besides the front passenger airbag also the side or head passenger airbags are deactivated.
Please comply with any differing
national legal regulations regardin
g the use of child safety seats.
•
If a child safety seat in which the child faces in the direction of travel is
used on the front passenger seat, the
front passenger seat must be moved
back and to the top fully in the highest position.•
If this is not done, a child seated on the front passenger seat may suffer
severe or even fatal injuries if the
front passenger airbag or airbags are
deployed. Have the airbag (or ai
rbags) deactivated if necessary
⇒page 182,
“Deactivating an airbag”.•
You should have the front passenger airbag (or airbags) reactivated just
as soon as you no longer use a child sa
fety seat on the front passenger seat.
Child safety and side airbag* Children must never be seated in
the deployment area of the side
airbags and head airbags.In the event of a side collision, the si
de airbags offer the vehicle occupants
enhanced protection. The side airbags are inflated in fractions of
a second in order to be able to provide
this protection
⇒page 179, “Function of
the side airbags”.
An airbag inflating develops such a strong force that an occupant who has not adopted an upright seated position may suffer
injuries from the airbag or as a result
of objects which are located within th
e deployment area of the side airbag.
WARNING (continued)
Fig. 181 Seated position of an unprotected child at risk from side airbagFig. 182 Child properly protected by safety seat
s2dk.1.book Page 187 Wednesday, April 8, 2009 12:23 PM

Transporting children safely
188
This applies particularly to children if they are not transported in accordance with legal requirements. The child is protected when seated in a child safety seat matching its age. Adequate room is available between th
e child and the deployment area of the side airbag and
head airbag. The airbag offers optimal protection.
WARNING
•
It is essential to always switch off
⇒page 182 the front passenger airbag
when attaching a child safety seat on
the front passenger seat where the
child is seated with its back facing in direction of travel (in some countries also when the child is facing the direction of travel). If this is not done, there is a risk of the child suffering severe
or even fatal injuries if the front
passenger airbag is deploy
ed. In certain countries national legal provisions
also require that the si
de and head airbags be
deactivated. When trans-
porting a child on the front passenger seat, please comply with the appro- priate national regulations regarding the use of child safety seats.•
When transporting a child on the fr
ont passenger seat, please comply
with the appropriate national regulations regarding the use of child safety seats.•
Children must never be seated with their head in the deployment area of
the side airbag - risk of injury!•
Do not place any objects within the deployment area of the side airbag -
risk of injury!Child seatClassification of child seats into groups Only child safety seats which have an official approval and are suit- able for the child, may be used.ECE-R 44 standard applies to child safety seats. ECE-R means: Economic Commis- sion of Europe - Regulation.
Child safety seats which have been tested for conformity to ECE-R 44 standard have a non-detachable test seal (a large E within a circle and below this the test number) attached to the seat. Child safety seats are classified in 5 groups: Children of more than 150 cm in height may use the seat belts fitted to the vehicle without a seat bolster.Use of child safety seatsAn overview of the usefulness of child se
ats on each of the seats according to the
ECE-R 44 standard:
Universal category - seat is suitable for all approved types of child safety seats. The seat can be fitted with
fixing eyes for the “
ISOFIX
*”system.
The divided rear seat - seat can be fitt
ed with fixing eyes for the system “
To p
Te t h e r
*” ⇒page 192, “Attaching child seat using the “Top Tether” system”.
Group
Weight
0
0 - 10 kg
⇒page 189
0+
up to 13 kg
⇒page 189
1
9 - 18 kg
⇒page 189
2
15 - 25 kg
⇒page 190
3
22 - 36 kg
⇒page 190
Child seat groups
Front passenger
seat
Rear seat outside
Rear seat middle
0


0+


1


2 and 3
AUA+
AUA+AT
AU
AUA+
AUA+AT
AU
AUA+
AUA+AT
AU
AU
AU
AU
AUA+AT
s2dk.1.book Page 188 Wednesday, April 8, 2009 12:23 PM

Transporting children safely
189
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Child seats of group 0/0+The optimal solution for babies of up to
about 9 months old weighing up to 10 kg
or babies up to about 18 mont
hs old weighing up to 13
kg is a child safety seat
which can be adjusted into the reclining position
⇒fig. 183
.
In view of the fact that such child seats are installed that the child is seated with its back facing the direction of travel, they
must not be used on the front passenger
seat
⇒page 186, “Use of child safety seats on the front passenger seat”.WARNING
•
It is essential to always switch off the front passenger airbag (airbags)
when attaching in exceptional circumstances a child safety seat on the front passenger seat where the child is seated
with its back facing in direction of
travel (in some countries also when the child is facing the direction of travel).
− in a specialist garage − or by using the switch for the front passenger airbag*
⇒page 183,
“Switch for the front passenger airbag*”.
•
In certain countries national legal provisions require that besides the
front airbag also the side or head ai
rbags are deactivated. Please comply
with any differing national legal regula
tions regarding the use of child safety
seats.
•
If this is not done, a child seated on
the front passenger seat may suffer
severe or even fatal injuries if the
front passenger airbag or airbags are
deployed.•
You should have the front passenger ai
rbag (or airbags) reactivated just
as soon as you no longer use a child sa
fety seat on the front passenger seat.
Child safety seats in Group 1Child seats in Group 1 are for babies and sm
all children up to 4 years of age with a
weight of between 9 and 18 kilograms. It is
best for children in the lower range of
this group, to use a child seat which allows
the child to sit with its back to the direc-
tion of travel. It is best for children in the upper range of the Group 0+, to use a child seat which allows the child to sit
⇒fig. 184
in the direction of travel.
Child safety seats in which the child is seat
ed with its back facing the direction of
travel, must not be used on the front passenger seat
⇒page 186, “Use of child
safety seats on the front passenger seat”.
WARNING
•
It is essential to always switch of
f the front passenger airbag (airbags)
when attaching in exceptional circumstances a child safety seat on the front
Fig. 183 Child seats of group 0/0+
WARNING (continued)
Fig. 184 Child seat with padded table in Group 1 installed on rear seat bench facing the direction of travel
s2dk.1.book Page 189 Wednesday, April 8, 2009 12:23 PM

Transporting children safely
190
passenger seat where the child is seated
with its back facing in direction of
travel (in some countries also when the
child is facing the direction of travel).
− in a specialist garage − or by using the switch for
the front passenger airbag*
⇒page 183,
“Switch for the front passenger airbag*”.
•
In certain countries national legal provisions require that besides the
front airbag also the side or head ai
rbags are deactivated. Please comply
with any differing national legal regula
tions regarding the use of child safety
seats.•
If this is not done, a child seated on the front passenger seat may suffer
severe or even fatal injuries if the
front passenger airbag or airbags are
deployed.•
You should have the front passenger ai
rbag (or airbags) reactivated just
as soon as you no longer use a child sa
fety seat on the front passenger seat.
Child safety seats in Group 2For children up to about 7 years of age
weighing between 15 and 25 kg the optimal
solution is a child safety seat in comb
ination with the three-point seat belt
⇒ fig. 185
.
WARNING
•
When transporting a child on the front passenger seat, please comply
with the appropriate national regulati
ons regarding the use of child safety
seats. If required, the airbag has to be deactivated,
− in a specialist garage − or by using the switch for the front passenger airbag*
⇒page 183,
“Switch for the front passenger airbag*”.
•
The shoulder part of the seat belt
must run approximately across the
middle of the shoulder and fit snugly agai
nst the chest. It must on no account
run across the neck. The lap part of the seat belt must run across the pelvis and fits snugly; it must not run over the belly. Tighten the belt webbing over your hip if necessary.•
Please comply with any differing nati
onal legal regulations regarding the
use of child safety seats.Child safety seats in Group 3For children of about 7 years of age weighi
ng between 22 and 36 kg and of a height
of less than 150 cm, the optimal solution
is a child safety seat (seat bolster) in
combination with the three-point seat belt
⇒fig. 186
.
WARNING (continued)
Fig. 185 Child seat in Group 2 installed on the rear seat facing the direction of travel
Fig. 186 Child seat in Group 3 installed on the rear seat facing the direction of travel
s2dk.1.book Page 190 Wednesday, April 8, 2009 12:23 PM

Transporting children safely
191
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Children of more than 150 cm in height may use the seat belts fitted to the vehicle without a seat bolster.
WARNING
•
When transporting a child on the front passenger seat, please comply
with the appropriate national regulations regarding the use of child safety seats. If required, the airb
ag has to be deactivated,
− in a specialist garage − or by using the switch for the front passenger airbag*
⇒page 183,
“Switch for the front passenger airbag*”.
•
The shoulder part of the seat belt must run approximately across the
middle of the shoulder and fit snugly against the chest. It must on no account run across the neck. The lap part of the seat belt must run across the pelvis and fits snugly; it must not run over th
e belly. Tighten the belt webbing over
your hip if necessary.•
Please comply with any differing nati
onal legal regulations regarding the
use of child safety seats.Attaching a child seat us
ing the “ISOFIX” system
There are two fixing eyes* between the backrest and the seat of the front passenger as well as on the rear exte
rior seats for fixing the “ISOFIX”
system child seat in place. On seats
where the fixing eyes are not visible,
the places which have eyes are marked
with signs with the “ISOFIX” logo
⇒
fig. 187
.
Install child seat – Insert the mounting funnels onto the locking eyes between the
seat backrest and the seat cushion
⇒
fig. 187
.
– Push the notched arms of the chil
d seat over the mounting funnels
into the locking eyes, until it is heard to lock
⇒
fig. 188
.
–
Pull on both sides of the child seat!
One can mount a child safety seat using the “ISOFIX” system quickly, easily and reli- ably. Please pay close attention to instruct
ions from the manufacturer of the child
safety seat when installing and removing the seat. Child seats fitted with the “ISOFIX” syst
em can only be mounted and fixed in a
vehicle fitted with an “ISOFIX” system when
these child seats have been released for
this type of vehicle according to the ECE-R 44 standard.
Fig. 187 Locking eyes (ISOFIX system)
Fig. 188 The ISOFIX child seat is pushed into the mounting funnels
AA
AB
s2dk.1.book Page 191 Wednesday, April 8, 2009 12:23 PM

Transporting children safely
192
You can obtain child seats with the “ISOFIX” attachment system from specialist garages who will also installed it as well. Complete installation instructions are
enclosed with the child safety seat.
WARNING
•
The locking eyes have just been de
veloped for child safety seats which
use the “ISOFIX” system. You should
therefore never attach other child
safety seats, seat belts or obje
cts to the locking eyes - hazard!
•
Ask an authorised Škoda Service Part
ner whether a child seat which you
bought for another vehicle is recommended for use in a Škoda before using an “ISOFIX” system.•
Certain child seats which use the “ISOFIX” system can be attached with
standard three-point seat belts. Please pay close attention to instructions from the manufacturer of the child safety seat when installing and removing the seat.
Note
•
Child seats which use the “ISOFIX” system are currently available for children
weighing from 9 up to 18 kg. This correspo
nds to an age range of from 9 months to
4 years.•
The child seats can also be fitted with the “Top Tether” system
⇒page 192.
Attaching child seat using the “Top Tether” systemIIn certain countries national
legal provisions also requir
e the equipment of the rear
seat with fixing eyes for child seat using the “Top Tether” system
⇒fig. 189
.
Always perform the installation and removal
of the child seat using the “Top Tether”
system as stated in the instructions fr
om the manufacturer of the child seat.
WARNING
•
Attach the child seats with the “Top Tether” system only to the points
provided for this purpose
⇒fig. 189
.
•
On no account should you equip your vehicle, e.g. mount screws or other
anchorage points.•
Pay attention to the important safety information regarding the use of
child seats.
Note
Store the remaining part of the belt for the “Top Tether” system in a textile pocket, which is located at the child seat.
Fig. 189 Rear seat: Top Te t h e r
s2dk.1.book Page 192 Wednesday, April 8, 2009 12:23 PM

Intelligent Technology
193
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Driving TipsIntelligent TechnologyElectronic stability programme (ESP)*GeneralGeneral The ESP aids you maintain control of your vehicle in situations in borderline driving situations such as when negotiating a curve too fast. The risk of skidding is reduced and your car thus offers greater driving stability depending on the conditions of the road surface. This occurs at all speeds. The following systems are integrated into the electronic stability programme:•
Electronic Differential Lock (EDL),
•
Traction control system (TCS),
•
Active driver-steering recommendation (DSR),
•
Antilock brake system (ABS),
•
Brake Assist,
•
Uphill-Start off-Assist.
Operating principle The ESP switches on automatically when the engine is started and then conducts a self-test. The ESP control unit processes data from the individual systems. It also processes additional measurement data which are supplied by highly sensitive sensors: the rotational velocity of the vehi
cle about its vertical axis, the lateral accel-
eration of the vehicle, the brakin
g pressure and the steering angle.
The direction which the driver wishes to ta
ke is determined based on the steering
angle and the speed of the vehicle and is constantly compared with the actual behaviour of the vehicle. If differences exis
t, such as the car beginning to skid, the
ESP will automatically brake the appropriate wheel. The car is stabilised again by the forces which take effect when the wheel is braked. Intervention into the brake system takes place primarily on the outer front wheel of a vehicle which tends to oversteer (tendency for the rear of the vehicle to break away) while occurs this is on the inner re
ar wheel of a vehicle which tends to under-
steer (tendency to shift out of the curve). This braking control cycle is accompanied by noises. The ESP operates in combination with the ABS
⇒page 197. If there is a fault in the
ABS system, the ESP also does not operate. The ESP warning light lights up in the instru
ment cluster when there is a fault on the
ESP
 ⇒page 39.
Switching off You can switch the ESP off and on again
as you wish, by pressing the button
⇒ fig. 190
. The ESP warning light lights up in th
e instrument cluster when the ESP is
switched off
 ⇒page 39.
The ESP should normally always be switched
on. It may be good practice in certain
exceptional cases, such as when you wish
to have wheel slip, to switch off the
system. Examples:
Fig. 190 ESP switch
s2dk.1.book Page 193 Wednesday, April 8, 2009 12:23 PM

Intelligent Technology
194
•
when driving with snow chains
•
when driving in deep snow or on a loose surface
•
when it is necessary to rock a ca
r free when it has become stuck.
then you should switch on the ESP again.
WARNING
It is also not possible for the ESP to overcome the physical limits of the vehicle. Even if a vehicle fitted with ESP you should still always adapt your style of driving to the condition of the
road surface and the traffic situation.
This particularly applies when driving on slippery and wet roads. The increased safety offered must not tempt you to take greater risks than other- wise - risk of an accident!
Note
•
All four wheels must be fitted with the same tyres in order to achieve problem-
free operation of the ESP. Differing rolling
circumferences of the tyres can lead to an
undesirable reduction in the engine output.•
Changes to vehicle (e.g. on engine, on the brakes, on chassis or other assign-
ment of tyres and wheels) can influence the function of the ESP
⇒page 241,
“Accessories, changes and replacement of parts”.Electronic Differential Lock (EDL)* The electronic differential lock pr
events an individual wheel from
slipping.Models fitted with ESP are equipped with electronic differential lock (EDL). General The EDL makes it much easier, and sometimes at all possible, to start off, accelerate and climb a steep hill when the conditio
ns of the road surface are unfavourable.
Operating principle The EDL is activated automatically, that is
without any action on the part of the
driver. It monitors the speeds of the driven wheels with the aid of the ABS sensors. Should only
one
drive wheel begin spinning on a slippery surface there will be an
appreciable difference in the speed of the driven wheels. The EDL function brakes the slipping wheel and the differential transmits a greater driving force to the other driven wheel. This control proces
s is also accompanied by noises.
Overheating of the brakes The EDL switches off
automatically if unusually severe
stresses exist in order to
avoid excessive heat generation in the
disc brake on the wheel which is being
braked. The vehicle can continue to be driv
en and has the same characteristics as a
vehicle not fitted with EDL. The EDL switches on again
automatically as soon as the brake has cooled down.
WARNING
•
Depress the accelerator carefully when accelerating on uniformly slip-
pery road surfaces, such as ice and sn
ow. The driven wheels might still spin
despite the EDL and affect the stability
of the vehicle - risk of an accident!
•
You should always adapt your style of driving to the condition of road
surface and to the traffic situation even
when your vehicle is fitted with EDL.
The increased safety offered must not tempt you to take greater risks than otherwise - risk of an accident!
Note
•
If the ABS or ESP warning light comes on,
this may also indicate a fault in the
EDL. Please have the car inspected as s
oon as possible by a specialist garage.
•
Changes to vehicle (e.g. on engine, on
the brakes, on chassis or other assign-
ment of tyres and wheels) can in
fluence the function of the EDL
⇒page 241,
“Accessories, changes and
replacement of parts”.
s2dk.1.book Page 194 Wednesday, April 8, 2009 12:23 PM