2009 SKODA OCTAVIA ECU

Inspecting and replenishing
225
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Pulling on the locking lever
⇒
page 224, fig. 208
will unlock the
bonnet fully.
– Grip with the hand under
the radiator grille and lift up the bonnet.
– Take the bonnet support out of its holder and set it in the opening
designed for it
⇒
page 224, fig. 209
.
Closing the bonnet – Lift the bonnet slightly and unhook the bonnet support. Press the
bonnet support into the hold
er designed to hold it.
– Allow the bonnet to drop from a height of about 20 cm into the lock -
bonnet
do not press down on it
!
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
For safety reasons, the bonnet must always be properly closed when
driving. One should therefore check that
the lock has in fact engaged prop-
erly after closing the bonnet.•
Stop your vehicle immediately while driv
ing if you notice that the lock is
not properly engaged and close the bonne
t properly - risk of an accident!
Caution
Never open the bonnet using the locking lever - danger of causing damage.Working in the engine compartment Particular care is required when carrying out any work in the engine compartment!There is a risk of injuries, scalding,
accidents and fire when working in the
engine compartment, e.g. inspecting and replenishing oil and other fluids. For
this reason, it is essential to comply with the warning instructions stated below and with the general applicable
rules of safety. The engine compart-
ment of your car is a hazardous area
⇒
.
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
Switch off the engine and pull out the ignition key.
•
Apply the handbrake firmly.
•
If your vehicle is fitted with a ma
nual gearbox, move the gearshift lever
into Neutral, or if it is fitted with
automatic gearbox, move the selector lever
into position P.•
Allow the engine to cool down.
•
Keep children clear of the engine compartment.
•
Never spill oil and other fluids over the hot engine. Such fluids (e.g. the
antifreeze contained in the coolant) may ignite!•
Avoid short circuits in the electrical system - particularly on the battery.
•
Never place your hand into the radiator fan as long as the engine is still
warm. The fan might suddenly start running!•
Never open the cap of the coolant expa
nsion bottle as long
as the engine
is still warm. The cooling system is pressurized!•
Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your
face, hands and arms from hot steam
or hot coolant.•
Do not let objects, such as e.g cleani
ng cloth or tools lie in the engine
compartment.•
If you wish to work under the vehicle, you must secure the vehicle from
rolling away and support it with suitab
le supporting blocks
; the lifting jack*
is not sufficient for this - risk of injury!•
In cases where it be necessary to carry out inspection work when the
engine is running there is an additional risk from rotating parts (e.g. the V-
se0.1.book Page 225 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
246
The fire extinguisher must
be checked by an authoris
ed person or company annu-
ally (please observe the differing legal requirements).
WARNING
If the fire extinguisher is not correc
tly attached, in case of sudden manoeu-
vres or an accident it can be “thrown” through the interior compartment and cause injuries.
Note
•
The fire extinguisher must comply with
the relevant and valid legal require-
ments.•
Pay attention to the expiration date of the fire extinguisher. If the fire extin-
guisher is used after the expiration date,
its proper function is
no longer assured.
•
The fire extinguisher is only supplied in
certain countries within the scope of
delivery.Vehicle tool kitThe vehicle tool kit and the lifting jack*, on which a note sticker is affixed, are stored in a box in the spare wheel*
⇒fig. 223
. There is also space here for the removable
ball for the trailer towing device*. The bo
x is attached with a strap on the spare
wheel. The vehicle tool kit contains
the following parts (depen
ding on equipment fitted):
•
Wire clamps for removing the full wheel trims,
•
Plastic clip for a wheel bolt cover,
•
Wheel wrench*,
•
To w i n g e y e ,
•
Adapter for the wheel bolts lock.*
•
Screwdriver* for removing the front fog lights
20).
After using the lifting jack*, screw in the arm of the lifting jack fully before placing it back in its storage area.
WARNING
•
The factory-supplied liftin
g jack* is only intended for your model of
vehicle. On no account attempt to lift a heavier vehicle or other loads - risk of injury!•
Ensure that the vehicle tool kit is
safely attached in the luggage compart-
ment.
Note
Ensure that the box is alwa
ys secured with the strap.
Tyre repair kit*The tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit contains a compressor, inflation bottle, operating instructions and accessories. The repair with the
tyre repair kit is
not at all intended to replace
a permanent
repair on the tyre, this repair only serves
to reach the next specialist garage. The
Fig. 223 Luggage compart- ment: storage compartment for vehicle tool kit
20)Valid for Octavia RS and Octavia Scout.
se0.1.book Page 246 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
248
WARNING
•
If you find yourself in flowing traffic switch on the hazard warning lights
system and place the warning triangle
on the side of the road at the
prescribed distance from your vehicl
e while observing all national legal
provisions. In this way you are protecting not only yourself but also other road users.•
Never start the engine with the vehicle
sitting on the raised jack - danger
of suffering injury.
Caution
If you have to change a wheel on a slope
first block the opposite wheel with a stone
or similar object in order to secure th
e vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.Changing a wheelAlways change a wheel on a level surface as far as possible. – Take off the full wheel trim*
⇒
page 249 or the caps
⇒
page 249.
– In the case of light alloy wheels remove the wheel trim cap
⇒
page 250.
– First of all slacken the safety wh
eel bolt * and afterwards the other
wheel bolts
⇒
page 250.
– Jack up the vehicle until the wheel to
be changed is clear of the ground
⇒
page 251.
– Unscrew the wheel bolts and place them on a clean surface (cloth,
paper etc.).
– Take off the wheel.
– Fit on the spare wheel and tighten the wheel bolts slightly. – Lower the car. – Tighten the wheel bolts firmly, al
ternately and diagonally using the
wheel wrench* (crosswise) and last the safety wheel bolt* ⇒
page 250.
– Mount the full wheel trim/w
heel trim cap or the caps.
Note
•
All bolts must be clean
and must turn easily.
•
You must never grease or oil the wheel bolts!
•
When fitting on unidirectional tyres, ensure that the tyres rotate in the correct
direction
⇒page 238.
Subsequent stepsAfter changing the wheel, you must perform the following steps. – Stow and attach the replaced wheel in the spare wheel well. – Stow the vehicle tool kit in the space provided. –
Check
the
tyre pressure
on the spare wheel just mounted as soon as
possible.
– Have the
tightening torque
of the wheel bolts
checked
with a torque
wrench as soon as possible. Steel and light alloy wheels must be tight-ened to a tightening torque of
120 Nm
.
– Have the defective tyre repaired as soon as possible.
se0.1.book Page 248 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
251
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Raise vehicle You have to raise the vehicle with the lifting jack* in order to be able to take off the wheel.Position the lifting jack* by selecting the jacking point which is closest to the wheel to be removed
⇒
fig. 228
. The jacking point is located directly
below the engraving in the lower sill. The engraving is only visible after opening the door. – Position the lifting jack* below the jacking point and move it up until
its claw is positioned di
rectly below the vertical web of the lower sill.
– Align the lifting jack* so that its claw grasps the web of the lower sill
and the base plate is resting flat on the floor.
– Turn the lifting jack* up further until the wheel is just clear of the
ground.
Ground which is soft and slippery
below the lifting jack* can cause the vehicle to
slip off the lifting jack*. It is therefore al
ways necessary to place the lifting jack* on
a solid surface or use a wide and stable ba
se. Use a non-slip base (e.g. a rubber foot
mat) if the
surface is smooth
, such as cobbled stones, a tiled floor, etc.
WARNING
•
Always raise the vehicle with the doors closed - risk of injury!
•
Take suitable measures to prevent the
base of the lifting jack from slip-
ping off - risk of injury!•
Not positioning the lifting jack* at
the specified points can result in
damage to the vehicle. The lifting jack* ca
n also slip off if it does not have
sufficient grip - risk of injury!•
It is important to support the vehicle with suitable supporting blocks if
you wish to work under the lifted vehicle - risk of injury!Securing wheels against being stolen* You need a special adapter for slackening the safety wheel bolts.– Pull off the full wheel trim/cap from the wheel hub or cap from the
safety wheel bolt.
– Insert the adapter with its toothed side fully into the inner toothing
of the safety wheel bolt right down in such a way that only the outer hexagon is jutting out
⇒
fig. 229
.
– Insert the wheel wrench* fully onto the adapter . – Slacken the wheel bolt, or tighten it firmly
⇒
page 250.
Fig. 228 Changing a wheel: Points for positioning car jac
kAA
AB
Fig. 229 Safety wheel bolt with adapter
AB
AA
AB
se0.1.book Page 251 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
264
– Unplug the plug connector and carefully take out the headlight in the
direction of arrow .
Installation takes place in the reverse order.
Note
We recommend that you have the headlight
setting checked by a specialist garage
after installing the headlight.Turn signal light at the frontChanging light bulb for turn signal light (at the front) – Switch the ignition and all lights off. – Remove the headlight
⇒
page 263.
– Turn the socket in the direction of arrow
OPEN (open)
and take it out
together with the light bulb for the turn signal light
⇒
fig. 243
.
– Press the defective light bulb into the socket, turn to the left and
remove.
– Press a new light bulb into the socket and turn the light bulb to the
right as far as the stop.
– Insert the socket with the changed light bulb into the headlight and
secure it by turning in the direction of arrow
CLOSE (close)
to the
right. Note
We recommend that you have the headlight
setting checked by a specialist garage
after installing the headlight.Front parking lights and low beamRemoving the light bulb for the parking light – Switch the ignition and all lights off. – Remove the headlight
⇒
page 263.
– Remove the protective cap
⇒
page 263, fig. 241
.
– Remove the socket
⇒
fig. 244
.
– Take the faulty bulb out of the socket and insert a new one. – Insert the protective cap.
A2
Fig. 243 Removing the light bulb for the turn signal light
Fig. 244 Removing the bulbs for the parking and low beam light
AB
AA
se0.1.book Page 264 Frida
y, April 10, 2009 3:19 PM

Index299
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data Power window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Power windows
Button in front passenger door and in rear doors
53
Buttons on the driver's door . . . . . . . . . . . . . . . . 52
Central locking system . . . . . . . . . . . . . . . . . . . . . 54
RRadiator fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Rear armrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83, 104
Rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Rear window
heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Rear window heater . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Rear-view mirror
Exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Interior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Recharge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Synchronisation . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Replacing fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Replacing the wiper blades . . . . . . . . . . . . . . . . . . . . . 71
Roof aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Running in the car . . . . . . . . . . . . . . . . . . . . . . . . . . . 201SSafe securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163Safety information
Engine compartment . . . . . . . . . . . . . . . . . . . . . 225
Safety wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Saving electrical energy . . . . . . . . . . . . . . . . . . . . . . . 202
Seat belt height adjuster . . . . . . . . . . . . . . . . . . . . . . 171
Seat belt warning light . . . . . . . . . . . . . . . . . . . . . . . . 170
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168, 172
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Height adjustment . . . . . . . . . . . . . . . . . . . . . . . . 171
Safety information . . . . . . . . . . . . . . . . . . . . . . . . 169
taking off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Seat heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Selector lever lock
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Selector lever positions . . . . . . . . . . . . . . . . . . . . . . . 134
Selector lever-emergency unlocking . . . . . . . . . . . 138
Service Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Service Interval Display . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting temperature
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Side lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Stability system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
after fuel tank has run empty . . . . . . . . . . . . . . 125
Diesel engines . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Petrol engines . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Steering
active driver-steering recommendation . . . . 195
Steering force assistance . . . . . . . . . . . . . . . . . . . . . 198
Storage compartment
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Storage compartments . . . . . . . . . . . . . . . . . . . . . . . . 99
Storage facilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Sun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Sun screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Switching lights on and off . . . . . . . . . . . . . . . . . . . . 58
Switching off the engine . . . . . . . . . . . . . . . . . . . . . . 125
TTaking care of your vehicle . . . . . . . . . . . . . . . . . . . 211
TCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142, 152
Temperature
outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
the first 1 500 kilometres . . . . . . . . . . . . . . . . . . . . . 201
The roof luggage rack system . . . . . . . . . . . . . . . . . . 93
Thickness of brake pads
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Tilting roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Top Tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
se0.1.book Page 299 Friday, April 10, 2009 3:19 PM