2009 SKODA OCTAVIA seats

Seats and Stowage
78
– Engage the reverse gear. – Move the right exterior mirror into the desired position
⇒
page 73.
– Take the vehicle out of gear. The set position of the exterior mirror is
stored.
Memory buttons Memory for the seat offers the possibility to store the individual driver seat and external mirror position. An individual posi
tion can be allocated to each of the three
memory buttons
⇒page 77, fig. 76
, that is three in total. After pressing the
corresponding memory button , the seat
and the exterior mirror are automati-
cally moved into the positions which
have been allocated to this button
⇒page 78.
Emergency Off You can interrupt the setting operation at an
y time, if you operate any button of the
driver seat.
Note
•
When storing settings with the memory buttons, we recommend that you begin
with the front button and assign a memory button to each additional driver.•
Each new setting stored with the same button erases the previous setting.
•
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual settin
g of the exterior mirror on the passenger
side for reversing.Assigning remote control to the memory buttonsAfter storing the settings of the seat and exterior mirrors, you have 10 seconds in order to assign the radio remote control to the appropriate memory button. – Withdraw the ignition key. – Press the unlock button
⇒
page 50. The setting is stored with the
memory button which you have selected.
If you wish to be able to retrieve the settings which are stored in the memory by also using the radio remote control, you have
to assign the radio remote control to a
memory button in each case. If you wish, you can obtain an additional
remote control key from an authorised
Škoda Service partner and then assign the remote control key to another memory button.
Note
•
If the radio remote control had previous
ly been assigned to another memory
button, this setting is then erased by the new assignment.•
If you assign the radio remote contro
l to a memory button which has already
been assigned to a radio remote control,
the old assignment is also replaced by a
new assignment in this case.•
The assignment of the radio remote control to a memory button is retained,
however, after reassigning the seats and exterior mirrors.Retrieving settings of the seat and mirrors You can retrieve the stored settings
either with the memory buttons
or with the remote control*.Retrieving settings with memory buttons – In order to retrieve the stored
setting, you have two possibilities:
–
One-touch automatic memory:
Briefly press the desired memory
button
⇒
page 77, fig. 76
. The seat and exterior mirror are moved
automatically into the stored positions (this applies only if the ignition is switched on and the speed is less than 5 km/h).
–
Memory keying
: Press and hold the desired memory button
pressed long enough until the seat and the exterior mirror are moved into the stored positions.
AB
AB
AB
AB
se0.1.book Page 78 Friday, April 10, 2009 3:19 PM

Seats and Stowage
79
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Retrieving settings with remote control – If the driver door is closed and the ignition is switched off, briefly press
the unlock button of the radio remote control
⇒
page 50 and then
open the driver door.
– The seat and exterior mirrors now move automatically into the stored
positions.
Retrieving setting of exterior mirror for reversing* – Turn the rotary knob for the exterior mirror setting into the position

⇒
page 73 before engaging the reverse gear.
The mirror returns into its initial position,
after the rotary knob is moved out of the
position
 and put into another position or if the speed is more than 15 km/h.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.
Note
If in the stored position the inclination an
gle of the seat backrest is more than 102°
in relation to the seat cushion, the seat backrest remains in this position, after reaching this angle, when
retrieving the setting by briefly pressing the memory
button. In order to achieve the stored setting, it is necessary to press the memory button again and hold it pressed until the seat is in the stored position.
Head restraintsBest protection is achieved if the top edge of the head restraint is at the same level as the uppe
r part of your head.
Adjusting the height of a head restraint – Grasp the side of the head restraint with both hands and push it in
upward direction as desired
⇒
fig. 77
.
– Move the head restraint downward
s if required by pressing and
holding the safety button with one hand
⇒
fig. 78
and by pressing
with the other hand the head restraint downwards.
Fig. 77 Adjusting head restraintFig. 78 Removing a head restraint
se0.1.book Page 79 Friday, April 10, 2009 3:19 PM

Seats and Stowage
80
Removing and installing a head restraint – Pull the head restraint up out of the seat backrest as far as the stop (on
the rear head restraints fold forward the seat backrest).
– Press the locking button in the direction of arrow
⇒
page 79, fig. 78

and pull the head restraint out.
– To re-insert the head restraint, push it down into the seat backrest far
enough until you hear the locking button engage.
The position of the front and rear outer head restraints is adjustable in height. The middle rear head restraint is adjustable in two positions. The head restraints must be adjusted to
match the size of the seat occupant.
Correctly adjusted head restraints togeth
er with the seat belts offer effective
protection for the occupants
⇒page 164, “Correct seated position”.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk
of injury!•
If the rear seats are occupied, the rear head restraint must not be in the
lower position.
Middle rear head restraintIIn certain countries national legal pr
ovisions also require the equipment
of the rear seat with fixing eyes for
child seat using the “Top Tether” system
⇒
page 191. For vehicles, which are eq
uipped with such fixing eyes, a
deviating sequence for removing th
e middle head restraint must be
observed. Removing and installing the rear middle head restraint – Pull the head restraint out of the
seat backrest as far as the stop.
– Press the locking button in the direction of arrow , press simultane-
ously the locking button into the opening using a flat screwdriver with a width of maximum 5 mm and pull out the head restraint.
– To re-insert the head restraint, push it down into the seat backrest far
enough until you hear the locking button engage.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk
of injury!
Fig. 79 Rear seats: middle head restraint
AA
AB
se0.1.book Page 80 Friday, April 10, 2009 3:19 PM

Seats and Stowage
81
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
If the rear seats are occupied, the rear head restraint must not be in the
lower position.Rear seatsFolding the rear seats forwards
To enlarge the luggage compartment, the rear seats can be folded forwards, if necessary remove the se
at cushions. The rear seats can be
folded forward individually on ve
hicles with divided rear seats*.
Folding seats forwards – Before folding the rear seats forwards, you must adapt the position of
the front seats in such a way that
they are not damaged when the rear
seats are folded forwards.
– Pull up the seat cushion in direction of arrow and fold forwards in
direction of arrow
⇒
fig. 80
.
– Press the unlocking knob and fold the seat backrest forwards
⇒
fig. 81
.
If the front seats are too far back, we
recommend that you have the rear head
restraints removed before the seat backrests are folded forward. Store the removed head restraints in such a way that they cannot be damaged or soiled. Please refer to the guidelines
⇒page 84.
Move seats into th
e initial position
WARNING (continued)
Fig. 80 Folding the seat cushion forwardsFig. 81 Unlock the seat back-rest
A1
A2
AA
Fig. 82 Lock the seat back-rest
se0.1.book Page 81 Friday, April 10, 2009 3:19 PM

Seats and Stowage
82
Move seats into the initial position – Install the head restraint in the
slightly lifted
seat backrest.
– Place the rear lateral seat belt behind the edge of the side trim
panel
⇒
fig. 82
.
– Then push the seat backrest back
into the upright position until the
securing knob clicks into place - ch
eck by pulling on the seat backrest.
– Make sure that the red pin is covered
⇒
page 81, fig. 81
.
– Fold the seat cushion back into its original position.
WARNING
•
The belts and the belt locks must be in
their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.•
The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment can slide forward if there is sudden braking - risk of injury!•
Pay attention that the seat backrests are correctly interlocked. It is only
then that the three-point seat belt for the middle seat can reliably fulfil its function.•
Before folding the seat backrest back
into the secure position, place the
rear lateral seat belt behind the edge of the side trim panel. Take suitable measures to prevent that the seat belt
is jammed between the seat backrest
and the side trim panel and is thus damaged.
Removing the seat cushionYou can enlarge the luggage compartment on vehicles with divided rear seats* by removing the rear seat. Removing – Fold the seat cushion forwards completely. – Press the wire clamps in the direction of the arrow
⇒
fig. 83
and
remove the seat cushion from its holder.
Installing – Press the wire clamps in the direction of the arrow and place it in its
holder.
– Fold the seat cushion back into its original position.
Caution
For vehicles with heated rear seats* it is
necessary to disconnect the plug connec-
tion for the power supply before removing the seat cushion. For reinstalling the seat cushion it is necessary to re-connect the plug connection.
AC
AB
Fig. 83 Removing seat cush- ions
se0.1.book Page 82 Friday, April 10, 2009 3:19 PM

Seats and Stowage
83
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rear seat armrest*– You can fold down the armrest at
the loop to enhance occupant
comfort
⇒
page 83, fig. 84
.
Seat heaters*
You can electrically heat the seat ba
ckrests and the surfaces of the front
seats and the two outer rear seats. – You can switch on and regulate the
seat heating of the driver or front
passenger seat by pressing the surfac
e of the regulator at the point at
which the symbol is located
 ⇒
fig. 85
.
– You can switch on and adjust the heat
ers of the left or right rear seats
by pressing the regulator
 ⇒
fig. 86
.
– With one press, you can switch the
heating to highest intensity which
is indicated by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is
down-regulated up to the switch-off. The intensity of the heating is indicated by the number of illuminated warning lights in the switch.
WARNING
If you have a subdued pain and/or te
mperature sensitivity, e.g. through
medication, paralysis or because of ch
ronic illness (e.g. diabetes), we
recommend not to use the seat heating. This can lead to burns on the back, the posterior and the
legs which are difficult to he
al. If the seat heating is
used, we recommend to make regular breaks in your journey when driving long distances, so that in specific cases as mentioned above the body can
Fig. 84 Rear seats: ArmrestFig. 85 Dash panel: Regu- lator for front seat heating
Fig. 86 Centre console at rear: Regulator for heating the rear seats
se0.1.book Page 83 Friday, April 10, 2009 3:19 PM

Seats and Stowage
84
recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution
•
You should not kneel on the seats or otherwise apply pressure at specific points
in order to avoid damaging the heating elements of the seat heaters.•
Do not use the seat heating if the seats are not occupied by persons or if objects
are fastened or stored on them, for exampl
e a child seat, a bag etc. A fault of the
heating elements in the seat heating can occur.•
Do not clean the seats moist
⇒page 216.
Note
•
The seat heating should only be switched
on when the engine is running. This
has a significant effect of sa
ving on the battery capacity.
•
If the on-board voltage drops, the seat
heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.PedalsConcerning a secure depressi
ng of the pedal, you should use only footmats from
the Škoda genuine
accessories.
Operation of the pedals must not be hindered!
WARNING
•
Greater pedal distances may be needed when there is a fault in the brake
system.•
Do not place any footmats or other additional floor coverings in the area
of the pedals in order to ensure that
all the pedals can be fully depressed and
are able to return unobstructed to their initial position - risk of accident!
•
There must be no objects on the floor which could roll under the pedals.
You would then no longer be able to
apply the brakes, operate the clutch or
accelerator - risk of accident!luggage compartmentLoading the luggage compartmentPlease observe the following in the inte
rest of having good handling char-
acteristics of
your vehicle:
– Distribute the items of luggage as evenly as possible. – Place heavy objects as far forward as possible. – Attach the items of luggage to the lashing eyes or the safety net*
⇒
page 85.
In the event of an accident, there is such a
high kinetic energy which is produced by
small and light objects that they can caus
e severe injuries. The magnitude of the
kinetic energy depends on the speed at wh
ich the vehicle is travelling and on the
weight of the object. The speed at which the
vehicle is travelling
is in this case the
more significant factor. Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object with a weight of 4.5 kg produces
an energy, which corresponds to 20 times
its own weight. This means that it results in a weight of approx. 90 kg. You can imagine the injuries that can occur, if this
“bullet” is flying through the interior
compartment and hits an occupant.
WARNING
•
Stow the objects in the luggage compartment and attach them to the
lashing eyes.
WARNING (continued)
WARNING (continued)
se0.1.book Page 84 Friday, April 10, 2009 3:19 PM

Seats and Stowage
85
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
Loose objects in the passenger compartment can be thrown forward
during a sudden manoeuvre or in case
of an accident and can injure the
occupants or other oncoming traffic. This risk is still increased, if the objects which are flying around are hit by a depl
oyed airbag. In this case, the objects
which are thrown back can injure the occupants - hazard.•
Please note that the handling properti
es of your vehicle may be affected
when transporting heavy objects as a result of the displacement of the centre of gravity. The speed and style
of driving must be adjusted accord-
ingly.•
The items carried in the luggage compar
tment should be stowed in such
a way that no objects are
able to slip forw
ard if there are any sudden driving
or braking manoeuvres undertaken - risk of injury!•
Never drive with the boot lid fully opened or slightly ajar otherwise
exhaust gases may get into the interior of the vehicle - risk of poisoning!•
On no account exceed the permissi
ble axle loads and the permissible
gross weight of the vehi
cle - risk of accident!
•
Never transport occupants in the luggage compartment!Caution
Please ensure that the heating elements of the rear window heater are not damaged as a result of objects sliding in this area.
Note
Tyre pressure must be adjusted to the load
⇒page 238.
Lashing eyesEyes are located on the sides of the lugg
age compartment for lashing the goods to
be loaded. You can also attach a floor fixing net*
to these eyes for lashing small objects.
The floor fixing net* together with the
installation instruction are stowed in a
container under the floor co
vering of the luggage comp
artment behind the spare
wheel.
WARNING (continued)
Fig. 87 Luggage compart- ment: Lashing eyes (Octavia)Fig. 88 Luggage compart-ment: Lashing eyes (Combi)
se0.1.book Page 85 Friday, April 10, 2009 3:19 PM