2009 SKODA OCTAVIA maintenance

Breakdown assistance
247
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
repair can be undertaken on
the vehicle immediately.
Please read the attached
instructions carefully before the repair. The tyre repair kit is located in a textile ba
g. There is a velcro fastener on the under-
side of the bag, with which the bag is atta
ched to the floor covering of the luggage
compartment in such a way that the side of the bag rests on the right side of the luggage compartment and on the seat backrest.Spare wheel*The spare wheel lies in a well under the floor covering of the luggage compartment and is fixed in place using special screws
⇒fig. 224
.
Before removing the spare wheel, you must take out the box with the vehicle tool kit box
⇒page 246, fig. 223
.
One should check the inflation pressure in the spare wheel (at best when generally checking the tyre air pressures - see sign on the fuel filler flap
⇒page 238) to
ensure that the spare wheel is always ready to use. Temporary spare wheel A warning label displayed on the rim of the temporary spare wheel indicates that your vehicle is equipped with a temporary spare wheel. Please observe the following notes when driving with a temporary spare wheel:
•
After fitting on the wheel, the warning st
icker must not be concealed (e.g. by the
wheel trim).•
D o n o t d r i v e w i t h th i s s p a re w h e e l a t m o re th a n 8 0 k m / h - ri s k o f a c c i d e n t. Av o i d
accelerating at full throttle, sharp braking and fast cornering.•
The inflation pressure for this spare wheel is identical to the inflation pressure
of the standard tyres. The temporary spar
e wheel R 18 must have an inflation pres-
sure of 420 kPa (4.2 bar)!•
Use this spare wheel only to reach the nearest specialist garage as it is not
intended for continuous use.•
No other summer or winter tyres must
be mounted on the rim of the spare
wheel R 18.Changing a wheelPreliminary workThe following steps should be carried out before actually changing the wheel. – If it is necessary to change a wheel, park the vehicle as far away as
possible from the traffic flow. The place you choose should be
level
.
–Have
all the occupants get out.
While changing a wheel, the occu-
pants of the vehicle should not stan
d on the road (e.g. behind a crash
barrier).
– Apply the
handbrake
firmly.
–Engage
1st gear
or if your vehicle is fitted with an automatic gearbox,
position the
selector lever into position P
.
– If a trailer is coupled, uncouple it.– Take the
vehicle tool kit
⇒
page 246 and the
spare wheel*

⇒
page 247 out of the luggage compartment.
Fig. 224 Luggage compart- ment: Spare wheel
se0.1.book Page 247 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
249
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
It is necessary to observ
e the guidelines given on
⇒page 240 if the vehicle is
subsequently fitted with tyres which are different to those it was fitted with at the works.
Note
•
If you find, when changing the wheel,
that the wheel bolts are corroded and
difficult to turn, the bolts mu
st be replaced before chec
king the tightening torque.
•
Drive cautiously and only at a moderate speed to a workshop where the tight-
ening torque can be checked.Full wheel trim*Pulling off – Hook the clamp found in the vehicle tool kit into the reinforced edge
of the full wheel trim.
– Push the wheel wrench* through the clamp, support the wheel
wrench* at the tyre and pull off the wheel trim.
Installing – First press the full wheel trim onto the wheel at the valve opening
provided. Then press the full wheel trim into the wheel in such a way that its entire circumference locks correctly in place. Caution
•
Use the pressure of your hand, do not knock on the full wheel trim! Heavy
knocks mainly on the points where the full
wheel trim has not been inserted into
the wheel, can result in damage to the guide and centering elements of the full wheel trim.
•
First check for yourself that the theft-deterrent wheel bolt is located
⇒ page 251 in the hole in the area of the valve before fitting the full wheel trim onto a steel wheel which is attached with a theft-deterrent wheel bolt.Wheel bolts with caps*Pulling off – Push the plastic clip sufficiently fa
r onto the cap until the inner catches
of the clip are positioned at the collar of the cap and detach the cap.
Installing – Push the caps fully onto the wheel bolts.The caps are located in the we
ll of the luggage compartment.
Fig. 225 Removing the cap.
se0.1.book Page 249 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
251
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Raise vehicle You have to raise the vehicle with the lifting jack* in order to be able to take off the wheel.Position the lifting jack* by selecting the jacking point which is closest to the wheel to be removed
⇒
fig. 228
. The jacking point is located directly
below the engraving in the lower sill. The engraving is only visible after opening the door. – Position the lifting jack* below the jacking point and move it up until
its claw is positioned di
rectly below the vertical web of the lower sill.
– Align the lifting jack* so that its claw grasps the web of the lower sill
and the base plate is resting flat on the floor.
– Turn the lifting jack* up further until the wheel is just clear of the
ground.
Ground which is soft and slippery
below the lifting jack* can cause the vehicle to
slip off the lifting jack*. It is therefore al
ways necessary to place the lifting jack* on
a solid surface or use a wide and stable ba
se. Use a non-slip base (e.g. a rubber foot
mat) if the
surface is smooth
, such as cobbled stones, a tiled floor, etc.
WARNING
•
Always raise the vehicle with the doors closed - risk of injury!
•
Take suitable measures to prevent the
base of the lifting jack from slip-
ping off - risk of injury!•
Not positioning the lifting jack* at
the specified points can result in
damage to the vehicle. The lifting jack* ca
n also slip off if it does not have
sufficient grip - risk of injury!•
It is important to support the vehicle with suitable supporting blocks if
you wish to work under the lifted vehicle - risk of injury!Securing wheels against being stolen* You need a special adapter for slackening the safety wheel bolts.– Pull off the full wheel trim/cap from the wheel hub or cap from the
safety wheel bolt.
– Insert the adapter with its toothed side fully into the inner toothing
of the safety wheel bolt right down in such a way that only the outer hexagon is jutting out
⇒
fig. 229
.
– Insert the wheel wrench* fully onto the adapter . – Slacken the wheel bolt, or tighten it firmly
⇒
page 250.
Fig. 228 Changing a wheel: Points for positioning car jac
kAA
AB
Fig. 229 Safety wheel bolt with adapter
AB
AA
AB
se0.1.book Page 251 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
253
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Start engineIt is important to connect the jump
-start cables in the correct order.
Connecting positive terminals – Attach one end to the positive terminal
⇒
fig. 230
of the
discharged battery .
– Attach the other end to the positive terminal of the battery
supplying the power .
Connecting negative term
inal and engine block
– Attach one end to the negative
terminal of the battery supplying
the power .
– Attach the other end to a solid metal part which is connected
firmly to the engine block, or
to the engine block itself.
Starting engine – Start the engine of the vehicle providing current and run the engine at
idling speed.
– Now start the engine of the vehicle with the discharged battery.
– Interrupt the attempt at starting an engine after 10 seconds if it does
not start right away and wait for about 30 seconds before repeating the attempt.
– Disconnect the cables on the engine in exactly the
reverse order
they
were connected up.
WARNING
•
The non-insulated parts of the terminal clamps must never make contact
with each other. Furthermore, the cable connected to the positive terminal of the battery must not come into contact with electrically conducting parts of the vehicle - risk of a short circuit!•
Do not affix the jump starting cables to the negative terminal of the
discharged battery. There is the risk
of detonating gas seeping out the
battery being ignited by the strong
spark which results from the engine
being started.•
Run the jump-start cables so that th
ey cannot be caught
by any rotating
parts in the engine compartment.•
Do not bend over the batteries - risk of caustic burns!
•
The vent screws of the battery cells must be tightened firmly.
•
Keep any sources of ignition (naked
flame, smouldering cigarettes etc.)
away from the battery - risk of an explosion!•
Never jump-start the batteries which have a too low electrolyte level -
risk of explosion and caustic burns!Tow-starting and towing vehicleGeneralPlease pay attention to the following in
structions if you are going to use a
tow rope:
Fig. 230 Jump-starting using the battery from another vehicle: A - flat vehicle battery, B - battery providing current
A1AAA2AB
A3
AB
A4
se0.1.book Page 253 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
255
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Carefully remove the cover as follows. – Guide the fingers into the opening
⇒
page 254, fig. 231
.
– By pulling in the direction of arrow , first of all slacken the cover in
the upper area on the side to the fog lights.
– Afterwards, also slacken the cover on the other side in the direction of
arrow and remove it.
– Screw in the towing eye by hand anticlockwise down to the stop
⇒
fig. 232
and tighten up using the wheel wrench* (push the wheel
wrench* through the eye).
– In order to reinstall the cover after sc
rewing out the towing eye, first of
all insert it starting on the side facing the marking. Then press the cover closed on the side facing the fog light. The cover must engage firmly.
Front towing eye for Octavia RS and Octavia Scout The towing eye is stored in th
e box for the vehicle tool kit.
Octavia RS – Guide one finger into the opening of the grille
⇒
fig. 233
.
– Unlock the cover by pulling it in direction and remove it.– Screw in the towing eye by hand anticlockwise down to the stop
⇒
fig. 232
and tighten up using the wheel wrench* (push the wheel
wrench* through the eye).
Fig. 232 Front bumper: Installing the towing eye
AAA1
A2
Fig. 233 Front bumper Octavia RS: Protective grilleFig. 234 Front bumper Octavia Scout: Cover
AA
A1
se0.1.book Page 255 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
257
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The car can be towed in with a tow bar or
a tow rope. Refer at the same time to the
following guidelines:•
Move
selector lever into N
.
•
The maximum towing speed is
50 km/h
.
•
The maximum permissible towing distance is
50 km
. The gear oil pump does
not operate when the engine is not runni
ng; the gearbox would not be adequately
lubricated at higher speeds an
d over longer towing distance.
Caution
If the vehicle is towed in by a recovery vehi
cle, it should only be towed in with the
front wheels raised. If the vehicle is raised at rear, the automatic gearbox is damaged! (Does not apply to the automatic gearbox DSG).
Note
The vehicle must be transported on a special ve
hicle or trailer if it is not possible to
tow in the vehicle in the way described or if the towing distance is greater than 50 km.Towing a vehicle with four-wheel drivePlease refer to the notes
⇒page 253.
The vehicle can be towed in using a tow ba
r or a tow rope or with the front axle
raised. The maximum towing speed is
50 km/h
, the maximum permissible towing
distance is
50 km
.
Note
The vehicle must be transported on a special ve
hicle or trailer if it is not possible to
tow in the vehicle in the way described or if the towing distance is greater than 50 km.
se0.1.book Page 257 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
259
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Fuse cover in engine compartment The fuse box in the engine comp
artment exists in two different
versions. You can determine which version your vehicle is fitted with after removing the fuse cover at the location of the fuses.On some vehicles, the battery cover
must be removed before removing
the fuse cover
⇒
page 232.
Removing fuse cover – Move the circlips
⇒
fig. 238
as far as the stop, the symbol

appears behind the circlip and remove the cover.
Installing fuse cover – Position the fuse cover on the fuse box and push the circlips as far
as the stop - the symbol
 is visible behind the circlip.
Caution
•
When unlocking and locking the fuse cover,
it must be pressed on the sides to
the box, otherwise damage can
occur to the locking mechanism.
•
Carefully position the fuse cover in th
e engine compartment. If the cover was
not correctly positioned, water can get into
the fuses and this results in a damage
to the vehicle!
Fuse assignment in engine compartmentCertain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
Fig. 238 Fuse cover in engine compartment
AA
AA
No.
Power consumer
Amperes
F1
Not assigned
F2
Control unit for automatic gearbox DQ 200
30
F3
Measuring circuit
5
F4
Valves for ABS
30/20
F5
Control unit for automatic gearbox
15
F6
Instrument cluster, windshield
wiper lever and turn sig-
nal light lever
5
F7
Power suppy terminal 15, Starter
40
F8
Radio
15
F9
Phone
5
F10
Engine control unit, Main relay
5/10
F11
Control unit for auxiliary heating
20
F12
Control unit for CAN databus
5
Fig. 239 Schematic repre- sentation of fuse carrier in engine compartment
se0.1.book Page 259 Frida
y, April 10, 2009 3:19 PM

Fuses and light bulbs
261
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Electrically adjustable
seats are protected by
automatic circuit breakers
, which
switch on again automatically after a fe
w seconds after the overload has been
eliminated.BulbsChanging bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Defect light bulbs should only be replaced
with light bulbs of the same type. The
designation is located on the light socket or the glass bulb. Changing certain bulbs is not something wh
ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to
12
Central locking control unit
10
13
Diagnostic socket, Light switch
10
14
Control unit for automatic gearbox, Selector lever lock
5
15
Central control unit - interior lights
5
16
Climatronic
10
17
Not assigned
18
Not assigned
19
Control unit for trailer detection
5
20
Not assigned
21
Cornering lights for the left and right side
10
22
Air blower for Climatronic
40
23
Front power window
30
24
Cigarette lighter
25
25
Rear window heaterRear window heater, Auxiliar
y heating (auxiliary heating
and ventilation)
2530
26
Power socket in the luggage compartment
20
27
Fuel pump relay, Injection valves (diesel engine)
15
28
Not assigned
29
Engine control unit, Crankcase ventilation heater
10
30
Control unit for automatic gearbox
20
31
Vacuum pump
20
32
Rear power window
30
33
Electric sliding/tilting roof
25
34
Control unit for convenience functions
20
35
Anti-theft alarm system
5
No.
Power consumer
Amperes
36
Headlight cleaning system
20
37
Front seat heating
30
38
Heated rear seats
30
39
Not assigned
40
Air blower for heating and air conditioning
40
41
Rear window wiper
15
42
Not assigned
43
Towing device
15
44
Towing device
20
45
Towing device
15
46
Heated windscreen washer nozzles
5
47
Relay for auxiliary heating
5
48
Not assigned
49
Light switch
5
No.
Power consumer
Amperes
se0.1.book Page 261 Frida
y, April 10, 2009 3:19 PM