2009 Seat Leon 5D lock

Communication
12Dial number
A telephone number can be vocally specified to the system
and then dialled.– Press button to talk ⇒page 6, fig. 1 . Activation of the system
is confirmed with by a tone.
– After the tone, say the command DIAL NUMBER.After this command the system will then request you to specify a telephone
number. A connection will then be established to the specified number. The
telephone number can be specified all at once, in blocks of digits (separated
by a brief pause), or as single digits. You can specify the digits from zero to
nine . After each block of digits you specify (separated by a brief pause) the
system will repeat the digits. The system can only recognise single digits
(two, three, etc.), and not combinations of digits (e.g. twenty-three). Notes on specifying telephone numbers:
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.
Example for entering a telephone number:
A running dialogue can be cancelled at any time by pressing button to
talk.
REPEAT
The specified name or all of the digits specified
up to this point will be repeated. The system will
then give the cue so that you
can specify additional digits or commands.
CORRECTION
The specified name or the last entered block of
digits will be deleted. The system will then give
the cue so that you can specify
additional digits or commands.
ERASE
All specified digits will be deleted. The system
will then give the cue Please, proceed> so that you can specify new
digits or commands.
AF
Speech com-
mand
Condition
Message
Action
DIAL NUMBER
Phone switched
on
please?>
Dialogue
for example,
ZERO, SEVEN,
THREE, ONE
three, one>
Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: Dial,
repeat, back, or
you can specify
additional digits>
Dialogue
THREE, NINE,
TWO

Dialogue
DIAL
being dialled.>
Dialogue -The
telephone
number
0731492 will be
dialledEnd of dialogue
AF
Sist Comunicacion_EN.book Seite 12 Mittwoch, 15. Juli 2009 6:45 18

Communication13
Controls and equipment
Redial– Press button to talk ⇒page 6, fig. 1 .
– After the tone, say the command REDIAL.After giving the command the last number dialled via the hands-free system
will be dialled again.
Example for the REDIAL command:
A running dialogue can be cancelled at any time by pressing button to
talk.To record names in the phone book
You can store names along with a telephone number in the
internal telephone book.– Press button to talk ⇒page 6, fig. 1 . The beep tone indicates
that the system is ready.
– After the tone, say the command STORE NAME.After giving the command the system will request you to specify a name and
telephone number to store in the internal telephone book. The telephone book has enough memory for 50 names and numbers. You can specify the
digits from
zero to nine .
The telephone number can be specified all at once, in blocks of digits (sepa-
rated by a brief pause), or as single digits. After each block of digits you
specify (separated by a brief pause) the system will repeat the digits. The
system can only recognise single digits (two, three, etc.), and not combina-
tions of digits (e.g. twenty-three).
Say STORE to store the entry into the telephone book.Speech command
Condition
Message
Action
REDIAL
Phone switched
on
being dialled.>
DialogueEnd of dialogue
AF
AF
AF
Speech command
Condition
Message
Action
STORE NAME
Tele pho ne bo ok
is not full
please?>
Dialogue
COMPANY XYZ
the name>
Dialogue
COMPANY XYZ
please?>
Dialogue
ZERO, ONE, TWO,
THREE
three>
Dialogue
FOUR, FIVE, SIX

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.
Sist Comunicacion_EN.book Seite 13 Mittwoch, 15. Juli 2009 6:45 18

Communication
14A running dialogue can be cancelled at any time by pressing button to
talk.
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.•Say the command delete or back to delete or correct the corresponding
block of digits.•Say repeat to have all the digits that have been recognised up to that
point repeated.•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.•A running dialogue can be cancelled at any time by pressing button to
talk.•The telephone book works only in conjunction with the hands-free speech
control system; the entries are not stored on the phone's SIM card.
Calling a name in the phone book–Press button to talk ⇒ page 6, fig. 1.
– After the tone, say the command SELECT NAMEAfter the system has recognised this command, you may select a stored entry
from the telephone book to call the required number. The system best recog-
nises names spoken by the person who stored the name.
Example for selecting a name from the internal telephone book
A running dialogue can be cancelled at any time by pressing button to
talk.
No command
mands are: Store,
repeat, back,
delete, or you can
specify addi-
tional digits>
Dialogue
STORE
saved.>
Dialogue - The
name COMPANY
XYZ with the tele-
phone number
0123456 will be
storedEnd of dialogue
AFAF
Speech command
Condition
Message
Action
SELECT NAME
Phone is
switched on, tele-
phone book con-
tains entries.
please?>
Dialogue
COMPANY XYZ

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: dial,
repeat, back>
Dialogue
DIAL
being dialled.>
Dialogue - The
telephone
number for Com-
pany XYZ is
being dialledEnd of dialogue
AF
AF
Sist Comunicacion_EN.book Seite 14 Mittwoch, 15. Juli 2009 6:45 18

Communication
24Speech commands for operating the internal telephone book:Control commands
The control commands are used to carry out functions that
have already been chosen.The control commands are used during or at the end of a dialogue to carry out
certain functions.
Possible commands
Dial number
A telephone number can be vocally specified to the system
and then dialled.– Press the talk button ⇒page 21, fig. 12 . Activation of the
system is confirmed with by a tone.
– After the tone, say the command DIAL NUMBER.After this command the system will then request you to specify a telephone
number. A connection will then be established to the specified number. The
telephone number can be specified all at once, in blocks of digits (separated
by a brief pause), or as single digits. You can specify the digits from zero to
nine . After each block of digits you specify (separated by a brief pause) the
system will repeat the digits. The system can only recognise single digits
(two, three, etc.), and not combinations of digits (e.g. twenty-three).
Speech command
Action
SELECT NAME
After this command, you can call a number that
has been recorded in the phone book under a
name.
STORE NAME
After this command you can store a name with a
telephone number in the phone book
DELETE NAME
After this command you can delete a name from
the phone book.
PLAY PHONE BOOK
After this command you can listen to the names
stored in the phone book
DELETE PHONE BOOK
After this command you can choose to delete the
entire phone book or just a single name
Speech command
Action
DIAL
Telephone number already entered is dialled.
STORE
A name is saved in the phonebook with its phone
number
CANCEL
Cancels a running dialogue.
REPEAT
The specified name or all of the digits specified
up to this point will be repeated. The system will
then give the cue so that you
can specify additional digits or commands.
CORRECTION
The specified name or the last entered block of
digits will be deleted. The system will then give
the cue so that you can specify
additional digits or commands.
ERASE
All specified digits will be deleted. The system
will then give the cue Please, proceed> so that you can specify new dig-
its or commands.AC
Sist Comunicacion_EN.book Seite 24 Mittwoch, 15. Juli 2009 6:45 18

Communication
26book has enough memory for 50 names and numbers. You can specify the
digits from zero to nine .
The telephone number can be specified all at once, in blocks of digits (sepa-
rated by a brief pause), or as single digits. After each block of digits you
specify (separated by a brief pause) the system will repeat the digits. The
system can only recognise single digits (two, three, etc.), and not combina-
tions of digits (e.g. twenty-three).
Say STORE to store the entry into the telephone book.
A running dialogue can be cancelled at any time by pressing the talk button ⇒ page 20, fig. 10.
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.•Say the command delete or back to delete or correct the corresponding
block of digits.•Say repeat to have all the digits that have been recognised up to that
point repeated.•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.•A running dialogue can be cancelled at any time by pressing the talk
button .•The telephone book works only in conjunction with the hands-free speech
control system; the entries are not stored on the phone's SIM card.
Speech command
Condition
Message
Action
STORE NAME
Telephone book
is not full
please?>
Dialogue
COMPANY XYZ
the name>
Dialogue
COMPANY XYZ
please?>
Dialogue
ZERO, ONE, TWO,
THREE
three>
Dialogue
FOUR, FIVE, SIX

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.
No command
mands are: Store,
repeat, back,
delete, or you can
specify addi-
tional digits>
Dialogue
STORE
saved.>
Dialogue - The
name COMPANY
XYZ with the tele-
phone number
0123456 will be
storedEnd of dialogue
AC
AC
Sist Comunicacion_EN.book Seite 26 Mittwoch, 15. Juli 2009 6:45 18