2009 Seat Leon 5D ESP

Communication
16A running dialogue can be cancelled at any time by pressing button to
talk.
Note
•Say the command Repeat , if you would like to have the specified name
repeated by the system.•If you then say No, the system will answer with and the dialogue
will be ended.To erase the phone book
You can delete the entire phone book or single entries.– Press the talk button ⇒page 6, fig. 1 .
– After the tone, say the command DELETE PHONE BOOK.After giving this command you can delete the entire internal phone book or
single entries as desired. Example for deleting the entire internal telephone book:If no command is specified, the system responds after about 5
seconds with the next cue.
Dialogue
No command
are: yes, no, repeat,
back>
Dialogue
YES

DialogueEnd of
dialogueAF
AF
Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no>
Dialogue
YES

Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no>
Dialogue
YES
is deleted.>
All entries in the
phone book will
be deleted.End of dialogue
Sist Comunicacion_EN.book Seite 16 Mittwoch, 15. Juli 2009 6:45 18

Communication17
Controls and equipmentExample for deleting single names from the internal telephone book:
Notes on the phone book
Take note of these tips an
d suggestions when using the
phone book.•It is important that names stored in the phone book have a noticeable
acoustic difference between them so the system can recognise the entries.•In the event that an telephone book entry is not recognised (e.g. if
someone else tries to call-up a name), the phone book entries can be read out
by giving the command PLAY PHONE BOOK.•The numbers zero to nine are recognised by the system. Say the numbers
clearly so that the system can recognise them easily.
Should the system say , check the status of the
hands-free system as follows.•Is the phone switched on?•Has the PIN code been entered?
Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no, repeat>
Dialogue
NO
The telephone
book will then be
read out.
No command
Talk button
pressed as the
entry to be
deleted is read
out.
delete the entry
(name)?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue

No command
mands are: Yes,
no>
Dialogue
YES
deleted.>
The entry will be
deleted and the
remaining
entries will be
read out.
All entries are
read out.
End of dialogue
Sist Comunicacion_EN.book Seite 17 Mittwoch, 15. Juli 2009 6:45 18

Communication19
Controls and equipment
Voice command mobile telephone installation
- Models: Ibiza / Ibiza SCBasic functions
The voice command system can be activated with the “press
to talk” button, located on the multi-function control.See ⇒page 31, “Bluetooth®”
Talk button
The voice command system can be activated with the “press to talk”
button located on the multi-function control.
If one of these buttons is pressed while using the voice command system, the
function is cancelled.
After pressing the “press to talk” button ⇒fig. 9 , wait a few seconds for
the sound signal, after which the vocal commands may be used. These commands may be used to manage the functions of the hands-free telephone
system as well as the phone book.
Phone book
The speech control system offers the option of creating and using an phone
book belonging to the vehicle system and independent of the mobile tele-
phone. This phone book may contain 50 entries.
WARNING
•Please concentrate on driving. As the driver, you have the responsibility
for your safety and that of others. For this reason, you should only use the
functions in a manner that allows you to maintain control of the vehicle in
all situations - otherwise, you may create an accident risk!•The speech system must not be used in cases of emergency, since the
voice changes in stressful situations. This could result in a failed or delayed
telephone connection. Always dial emergency numbers manually!
Fig. 9 Talk button on the
multi-function control
AC
AC
Sist Comunicacion_EN.book Seite 19 Mittwoch, 15. Juli 2009 6:45 18

Communication
22Information on radio displayAn incoming call is indicated on the display. To accept, press button on
the multifunction control or multi-function button on the radio ⇒
page 21, fig. 11 . To reject the call, press multi-function button on the
radio ⇒page 21, fig. 11 .
To cancel the outgoing call, press multi-function button on the radio
⇒ page 21, fig. 11 .
Information regarding the mobile phone coverage is displayed on the radio
display.
Dialogue
The voice command system can be activated with the “press
to talk” button, located on the multi-function control.In this manual, Dialogue is defined as the time in which the speech control
system may receive vocal commands and provide assistance for completion
of different functions in case the user is hesitant and unsure how to proceed.
The system also responds by vocal messages. The dialogue is started and
Fig. 13 Incoming callFig. 14 Outgoing phone
call
AE
AA
AB
ABFig. 15 Current phone
call
Sist Comunicacion_EN.book Seite 22 Mittwoch, 15. Juli 2009 6:45 18

Communication25
Controls and equipmentNotes on specifying telephone numbers:
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.
Example for entering a telephone number:
A running dialogue can be cancelled at any time by pressing the talk button ⇒ page 19, fig. 9 .
Redial– Press the talk button .
– After the tone, say the command REDIAL.After giving the command the last number dialled via the hands-free system
will be dialled again.
Example for the REDIAL command:
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 20, fig. 10 .To record names in the phone book
You can store names along with a telephone number in the
internal telephone book.– Press the talk button . The beep tone indicates that the system
is ready.
– After the tone, say the command STORE NAME.After giving the command the system will request you to specify a name and
telephone number to store in the internal telephone book. The telephone
Speech command
Condition
Message
Action
DIAL NUMBER
Phone switched
on
please?>
Dialogue
for example,
ZERO, SEVEN,
THREE, ONE
three, one>
Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: Dial,
repeat, back, or
you can specify
additional digits>
Dialogue
THREE, NINE,
TWO
two>
Dialogue
DIAL
being dialled.>
Dialogue -The tel-
ephone number
0731492 will be
dialledEnd of dialogue
AC
Speech command
Condition
Message
Action
REDIAL
Phone switched
on
being dialled.>
DialogueEnd of dialogue
AC
AC
AC
Sist Comunicacion_EN.book Seite 25 Mittwoch, 15. Juli 2009 6:45 18

Communication
26book has enough memory for 50 names and numbers. You can specify the
digits from zero to nine .
The telephone number can be specified all at once, in blocks of digits (sepa-
rated by a brief pause), or as single digits. After each block of digits you
specify (separated by a brief pause) the system will repeat the digits. The
system can only recognise single digits (two, three, etc.), and not combina-
tions of digits (e.g. twenty-three).
Say STORE to store the entry into the telephone book.
A running dialogue can be cancelled at any time by pressing the talk button ⇒ page 20, fig. 10.
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue .•A Plus (+) can also be placed ahead of the 20 digits.•Say the command delete or back to delete or correct the corresponding
block of digits.•Say repeat to have all the digits that have been recognised up to that
point repeated.•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.•A running dialogue can be cancelled at any time by pressing the talk
button .•The telephone book works only in conjunction with the hands-free speech
control system; the entries are not stored on the phone's SIM card.
Speech command
Condition
Message
Action
STORE NAME
Telephone book
is not full
please?>
Dialogue
COMPANY XYZ
the name>
Dialogue
COMPANY XYZ
please?>
Dialogue
ZERO, ONE, TWO,
THREE
three>
Dialogue
FOUR, FIVE, SIX

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.
No command
mands are: Store,
repeat, back,
delete, or you can
specify addi-
tional digits>
Dialogue
STORE
saved.>
Dialogue - The
name COMPANY
XYZ with the tele-
phone number
0123456 will be
storedEnd of dialogue
AC
AC
Sist Comunicacion_EN.book Seite 26 Mittwoch, 15. Juli 2009 6:45 18

Communication27
Controls and equipment
Calling a name in the phone book– Press the talk button .
– After the tone, say the command SELECT NAMEAfter the system has recognised this command, you may select a stored entry
from the telephone book to call the required number. The system best recog-
nises names spoken by the person who stored the name.
Example for selecting a name from the internal telephone book
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 20, fig. 10 .
Listening to the phone book
You can have the entries stored in the internal telephone book
read out to you.– Press the talk button ⇒page 20, fig. 10 . The beep tone indi-
cates that the system is ready.
–Say the command PLAY PHONE BOOK.After giving the command the system will read out the entries stored in the
phone book. If you press the talk button as an entry is being read, the
system will call the telephone number for that entry. Once the dialogue is
complete and the system is reactivated, you can also select an entry to call by
specifying the stored name.
Example for the PLAY PHONE BOOK command:
Speech command
Condition
Message
Action
SELECT NAME
Phone is
switched on, tele-
phone book con-
tains entries.
please?>
Dialogue
COMPANY XYZ

Dialogue
If no command is specified, the system responds after about 5 seconds
with the next cue.No command
mands are: dial,
repeat, back>
Dialogue
DIAL
being dialled.>
Dialogue - The
telephone
number for Com-
pany XYZ is being
dialledEnd of dialogue
AC
AC
Speech command
Condition
Message
Action
PLAY PHONE
BOOK
The telephone
book contains
entries.
The telephone
book will then be
read out.End of dialogue
AC
AC
Sist Comunicacion_EN.book Seite 27 Mittwoch, 15. Juli 2009 6:45 18

Communication
28Example for selecting an entry:To erase names from the phone book
You can delete entries from the internal telephone book.– Press the talk button ⇒page 19, fig. 9 . The beep tone indi-
cates that the system is ready.
– After the tone, say the command DELETE NAME.After giving this command you can delete a stored entry from the internal tele-
phone book. Example for deleting single names from the internal telephone book:
A running dialogue can be cancelled at any time by pressing the talk button
⇒ page 19, fig. 9 .
Note
•Say the command Repeat, if you would like to have the specified name
repeated by the system.•If you then say No, the system will answer with and the dialogue
will be ended.
Speech command
Condition
Message
Action
PLAY PHONE
BOOK
The telephone
book contains
entries; the talk
button is
pressed as the
entry is being
read out.
being dialled.>
The selected
name will be
repeated. The tel-
ephone number
will be dialled.End of dialogue
ACAC
Speech command
Condition
Message
Action
DELETE NAME
The telephone
book contains
entries.

Dialogue
COMPANY XYZ
the entry Company
XYZ?>
Dialogue
If no command is specified, the system responds after about 5
seconds with the next cue.
Dialogue
No command
are: yes, no, repeat,
back>
Dialogue
YES

DialogueEnd of dia-
logue
AC
Sist Comunicacion_EN.book Seite 28 Mittwoch, 15. Juli 2009 6:45 18