2009 Seat Ibiza ST bulb

If and when215
Safety First
Operating instructions
Practical tips
Technical Data
– Move the loop in the direction of the arrow and remove the
cover ⇒page 214, fig. 140 .
– Remove connector ⇒ page 214, fig. 141 by pulling outward.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.Dipped beam and side lights
– Raise the bonnet.
– Remove the loop ⇒fig. 142 in the direction of the arrow and
remove the cover.
– Remove the connector ⇒fig. 143 from the bulb.
– Unclip the retainer spring ⇒fig. 143 pressing inwards to the
right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.
A1
A2Fig. 142 Dipped beam
headlights
Fig. 143 Dipped beam
headlights
A1
A2A3
Ibiza ST_EN.book Seite 215 Dienstag, 12. Januar 2010 4:03 16

If and when
216Turn signal bulb– Raise the bonnet.
– Rotate the bulb holder ⇒fig. 144 to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Changing bulbs. Single headlightSingle headlights summary
Dipped/main beam headlights
Side lights.
Turn signal
Fig. 144 Turn signal light
AA
Fig. 145 Single headlight
AAABAC
Ibiza ST_EN.book Seite 216 Dienstag, 12. Januar 2010 4:03 16

If and when217
Safety First
Operating instructions
Practical tips
Technical Data
Dipped/main beam headlights – Raise the bonnet. – Remove the loop
⇒fig. 146 in the direction of the arrow and
remove the cover.
– Remove the connector ⇒fig. 147 from the bulb.
– Unclip the retainer spring ⇒fig. 147 pressing inwards to the
right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.
Side lights – Raise the bonnet.
– Move the loop ⇒fig. 146 in the direction of the arrow and
remove the cover.
Fig. 146 Dipped
beam/main beam, single
headlightFig. 147 Dipped
beam/main beam, single
headlight
A1
A2A3
Fig. 148 Side lights
A1
Ibiza ST_EN.book Seite 217 Dienstag, 12. Januar 2010 4:03 16

If and when
218
– Remove the bulb holder ⇒page 217, fig. 148 outwards.
– Replace the bulb by pulling it out and inserting the replacement.
– Installation is done in the reverse order.Turn signal bulb– Raise the bonnet.
– Rotate the bulb holder ⇒fig. 149 to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Changing the rear lights (on the wing)Overview of tail lightsTail lights in side panel•Brake lights•Side lights•Turn signal lightAccessing the side light bulbs–Open the rear lid.
– Look for a lid with a grill behind the side lights.
A4
Fig. 149 Single turn
signal lamp
AA
Fig. 150 Side lights
Ibiza ST_EN.book Seite 218 Dienstag, 12. Januar 2010 4:03 16

If and when219
Safety First
Operating instructions
Practical tips
Technical Data
– Remove the lid with a flat screwdriver, placing it in notch
⇒page 218, fig. 150 .Changing bulbs– Remove the bulbholder by pressing the clip ⇒fig. 151 and
pulling outwards.
– Replace the faulty bulb, rotating it to the left and outwards.
– To refit follow the steps in reverse order, taking special care when fitting the bulb holder.
Changing the rear lights (on the rear lid)Overview of tail lightsLights on the rear lid•Reverse lights•Side lights•Fog lightsAccessing the rear lid lights–Open the rear lid.
– On the rear lid lining there is a lid behind each light.
AA
Fig. 151 Removing the
bulbholderAB
Fig. 152 Lights on the
rear lid
Ibiza ST_EN.book Seite 219 Dienstag, 12. Januar 2010 4:03 16

If and when
220
– Remove the lid with a flat screwdriver, placing it in notch ⇒page 219, fig. 152.Changing bulbs– Remove the bulbholder by pressing the fastening clips
⇒fig. 153 and pulling outwards.
– Replace the faulty bulb, rotating it to the left and outwards.
– To refit follow the steps in reverse order, taking special care when fitting the bulb holder.
Side turn signal bulbs– Press the turn signal to the left or to the right to remove the bulb.
– Remove the bulb holder from the turn signal.
– Remove the failed bulb and replace with a new bulb.
– Insert the bulb holder in the turn signal guide until it clicks into place.
– First fit the turn signal in the opening in the chassis, fastening the tabs ⇒fig. 154 , and then fit in the bulb as shown by the
arrow ⇒fig. 154 .
AA
Fig. 153 Removing the
bulbholder
AB
Fig. 154 Side turn
signals
A1A2
Ibiza ST_EN.book Seite 220 Dienstag, 12. Januar 2010 4:03 16

If and when221
Safety First
Operating instructions
Practical tips
Technical Data
Number plate light– Insert the flat part of a screwdriver into the special slot and
remove the number plate light from its moulding.
– Remove the connector and extract the bulb. After changing the bulb, fit the connector again.
– Place the light in its moulding, pr essing the left side. Once it is
fitted into place, press the right side until you hear a click.
Interior light and front reading lightsTo r e m o v e t h e g l a s s
– Insert a fine screwdriver between the casing and the glass ⇒fig. 156 .
– Carefully remove the glass, levering it to avoid possible damage.
To replace the bulbs
– Pull the bulbs outwards.
– To remove the central bulb, hold and press to one side.
Assembly
– Proceed in the reverse order, pressing gently on the outer edge of the side light.
Fig. 155 Remove the
number plate light.
Fig. 156 Front reading
light
Ibiza ST_EN.book Seite 221 Dienstag, 12. Januar 2010 4:03 16

If and when
222
– First fit the glass with the fastening tabs over the frame of the switch. Next press the front part until the two long tabs click on
the support.Additional brake lights*Given the difficulty involved in the replacement of this light it should be done
by the Technical Service.Luggage compartment light
– Extract the tulip shaped fitting by pressing on the inside edge of this -arrow- using the flat side of a screwdriver ⇒fig. 157 .
– Press the bulb sideways and remove it from its housing ⇒fig. 158 .Jump-startingJump leads
The jump lead must have a sufficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Fig. 157 Luggage
compartment light
Fig. 158 Luggage
compartment light
Ibiza ST_EN.book Seite 222 Dienstag, 12. Januar 2010 4:03 16