
Unlocking and locking
102Ta i l g a t eUnlocking and locking
The operation of the tailgate opening system is electric. It is 
activated by using the handle on the tailgate
Opening the tailgate
– Pull on the release lever and lift the tailgate  ⇒fig. 65 . The tail-
gate will then open.
Closing the tailgate
– Grip the tailgate by one of the two handles on the interior lining  and close it, using a light movement.The system may or may not operate depending on the situation of the vehicle.
If the tailgate is locked then it cannot be opened, however if it is unlocked 
then the opening system is operat ive and the boot may be opened.
To the locking / unlocking status, press the button   or the button   on 
the remote control key.
A warning appears in the instrument panel if the tailgate is open or not prop-
erly closed.* An audible warning is also given if the tailgate is open when the 
car is driven faster than 6 km/h*.
Fig. 65  Tailgate: opening 
from the outside
Fig. 66  Detail of the 
inside of the tailgate: 
hand grip
A1
AlteaXL_EN.book  Seite 102  M ontag, 2. Februar 2009  12:26 12 

Unlocking and locking103
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
WARNING
•
Always close the tailgate properly. Risk of accident or injury.
•
The tailgate must not be opened when the reverse or rear fog lights are 
lit. This may damage the lighting units.
•
Do not close the tailgate by pushing  it down with your hand on the rear 
window. The glass could smash. Risk of injury!
•
Ensure the tailgate is locked after closing it. If not, it may open unex-
pectedly while driving.
•
If the tailgate is not fully closed, open it with the handle and close it 
again correctly. Do not try to close it by pressing on the surface of the tail-
gate, as this may damage the surface.
•
Never allow children to play in or ar ound the vehicle. A locked vehicle 
can be subjected to extremely high and low temperatures, depending on 
the time of year, thus causing serious injuries/illness. It could even have 
fatal consequences. Close and lock both  the tailgate and all the other doors 
when you are not using the vehicle.
•
Closing the tailgate without observing and ensuring it is clear could 
cause serious injury to you and to third  parties. Make sure that no one is in 
the path of the tailgate.
•
Never drive with the tailgate open or half-closed, exhaust gases may 
penetrate into the interior of th e vehicle. Danger of poisoning!
•
If you only open the tailgate, do not leave the key inside. The vehicle 
will not be opened if the key is left inside.
Emergency opening
This allows the vehicle to be opened if the central locking 
does not operate (for example, if the battery is flat)There is a groove in the boot allowing access to the emergency 
opening mechanism.
Opening the tailgate from inside the luggage compartment
– Insert the key bit in the groove and unlock the locking system,  turning the key from right to left, as shown by the arrow 
⇒fig. 67 .
Fig. 67  Tailgate: emer-
gency open
AlteaXL_EN.book  Seite 103  M ontag, 2. Februar 2009  12:26 12 

Unlocking and locking
104WindowsOpening or closing the windows electrically
The front and rear electric windows can be operated by using 
the controls on the driver's door.Opening and closing the windows
– Press the button   to open a window.
– Pull button   to close a window  ⇒.Always close the windows fully if you park the vehicle or leave it unattended 
⇒.
You can use the electric windows for approx. 10 minutes after switching off 
the ignition if neither the driver door  nor the front passenger door has been 
opened and the key has not been  removed from the ignition. Buttons on the driver's door
Button for window in front left door
Button for window in front right door
Buttons for rear windows* Safety switch for deactivating the electric window buttons in the rear 
doors
Button for window in rear left door
Button for window in rear right door
Safety switch 
*
Safety switch   on the driver's door  can be used to disable the electric 
window buttons in the rear doors.
Safety switch not pressed: buttons on rear doors are activated.
Safety switch pressed: buttons on rear doors are deactivated.
WARNING
•
Incorrect use of the electric  windows can result in injury.
•
Never close the tailgate without observing and ensuring it is clear, to do 
otherwise could cause serious injury to you and third parties. Make sure 
that no one is in the path of a window.
•
Always take the vehicle key with you when you leave the vehicle.
•
Never leave children or disabled persons in the vehicle, particularly if 
they have access to the keys. An unco ntrolled use of the key could start the 
engine or activate any electric equi pment (e.g. electric windows), causing 
risk of accident. The doors can be lock ed using the remote control key. This 
could make the aid difficult in an emergency situation.
•
The electric windows will work unti l the key has been removed from the 
ignition and one of the front doors has been opened.
•
If necessary, use the safety switch to disable the rear electric windows. 
Make sure that they have been disabled.
Fig. 68  Detail of driver 
door: controls for the front 
and rear windows
A1A2A3A4A5
A3
AlteaXL_EN.book  Seite 104  M ontag, 2. Februar 2009  12:26 12 

Unlocking and locking105
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
Note
If the window is not able to close because it is stiff or because of an obstruc-
tion, the window will automatically open again  ⇒page 105. If this happens, 
check why the window could not be clos ed before attempting to close it 
again.One-touch opening and closing
One-touch opening and closing means you do not have to 
hold down the button.One-touch closing
– Pull up the window button briefl y up to the second position. The 
window closes fully.
One-touch opening
– Push down the window button briefly up to the second position.  The window opens fully.
Restoring one-touch opening and closing
– Close all windows.
– Use the key to lock the vehicle from outside and hold the key in  the lock position for at least one second. The one-touch function 
is now ready for operation.The buttons  ⇒page 104, fig. 68    and   have two levels for opening the 
window and two for closing it. This makes it easier to open and close windows 
to the desired position. One-touch closing does not work when the ignition has been switched off, 
even if the key is in the ignition.
The automatic open and close function wi
ll not work if the battery has been 
temporarily disconnected, or if the battery is flat. The function then has to be 
reactivated.
The one-touch function and roll-back function will not work if there is a 
malfunction in the electric windows.  Contact an Authorised Service Centre.
Roll-back function
The windows have a roll-back function. This reduces the risk 
of injuries when the windows are closing.•
If a window is obstructed when closing automatically, the window stops 
at this point and lowers immediately  ⇒.
•
If this happens, check immediately (within 10 seconds) why the window 
could not be closed before  attempting to close it again. After 10 seconds the 
normal automatic function resumes.
•
If the window is still obstructed, th e window will stop at this point.
•
If there is no obvious reason why the window cannot be closed, try to 
close it again within five seconds.
If you wait longer than 5 - 10 seconds, the window will open fully when you 
operate one of the buttons. One-touch closing is reactivated.
The one-touch function and roll-back function will not work if there is a 
malfunction in the electric windows. Contact an Authorised Service Centre.
WARNING
•
Incorrect use of the electric windows can result in injury.
A1
A2
AlteaXL_EN.book  Seite 105  M ontag, 2. Februar 2009  12:26 12 

Unlocking and locking
106•
Always take the key with you when leaving the vehicle, even if you only 
intend to be gone for a short time. Please ensure that children are never left 
alone inside the vehicle.
•
The electric windows will work until the key has been removed from the 
ignition and one of the front doors has been opened.
•
Never close the tailgate without observin g  a n d  e n s u r i n g  i t  i s  c l e a r,  t o  d o  
otherwise could cause serious injury to you and third parties. Make sure 
that no one is in the path of a window.
•
Never allow people to remain in th e vehicle when you close the vehicle 
from the outside. The windows cannot be opened even in an emergency.Note
The roll-back function is deactivated if the windows are closed from the 
outside of the vehicle using the ignition key for convenience closing 
⇒ page 106.Convenience opening and closing* Using the door lock
– Hold the key in the door lock of the driver door in either the 
locking or the unlocking position until all windows are either 
opened or closed.
– Release the key to interrupt this function. Using the remote control
– Push the lock button on the remote control for about 3 seconds. 
All windows which function electric ally will be either opened or 
closed.
– Press the unlock button to interrupt the function.
– Once the windows are completely closed, the indicators will  flash.
Sliding/tilting roof*Opening and closing the sliding/tilting roof
The sliding/tilting sunroof is opened and closed using the 
rotary button when the ignition is switched on.
WARNING (continued)
Fig. 69  Roof lining 
description: rotary sun 
roof control / deflector
AlteaXL_EN.book  Seite 106  M ontag, 2. Februar 2009  12:26 12 

Unlocking and locking107
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
Closing the sliding/tilting sunroof
– Turn the rotary button to position    ⇒fig. 69  ⇒ .
Opening/tilting the sliding/tilting sunroof
– Turn the rotary button to position  . The sunroof opens to the  convenience position where wind noise is reduced.
– To open the roof further, turn the switch to position   and hold  the switch in this position until the roof opens to the desired 
position.
Tilting the sliding/tilting sunroof
– Turn the rotary button to position  .Always close the sliding/tilting roof fully if you park the vehicle or leave it 
unattended  ⇒.
The sliding/tilting sunroof can be operat ed for up to about ten minutes after 
the ignition has been switched off, pr ovided the driver door and the front 
passenger door are not opened.
Sunroof blind
The sunroof blind is opened together with  the sliding/tilting roof. If required, 
it can be closed by hand when the sunroof is closed.
WARNING
•
Incorrect use of the sliding/tilting sunroof can result in injury.
•
Never close the sliding/tilting sunr oof without observing and ensuring 
it is clear, to do otherwise could cause serious injury to you and others. 
Make sure that no one is in the  path of the sliding/tilting sunroof.
•
Always take the vehicle key with you when you leave the vehicle.
•
Never leave children or disabled persons in the vehicle, particularly if 
they have access to the keys. Unsupervised use of a key could mean that 
the engine is started or that electrical equipment is used (e.g. electric 
sliding/tilting sunroof). Risk of accide nt! The doors can be locked using the 
remote control key. This could make the aid difficult in an emergency situ-
ation.
•
The sliding/tilting sunroof continues  to function until one of the front 
doors is opened and the key removed from the ignition.
Convenience closing*Using the door lock
– Hold the key in the door lock of the driver's door in the locking  position until the sliding/tilting sunroof is closed.
– Release the key to interrupt this function.
Using the remote control
– Push the lock button on the remo te control for about 3 seconds. 
The sliding/tilting sunroof is closed.
– Release the unlock button to interrupt the function.
– When the sliding/tilting sunroof has closed completely, the indi- cators flash once.
AAAB
AC
AD
WARNING (continued)
AlteaXL_EN.book  Seite 107  M ontag, 2. Februar 2009  12:26 12 

Lights and visibility109
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
Lights and visibilityLightsSwitching lights on and off 
 
Switching on the side lights
– Turn the light switch ⇒ fig. 72 to position 
.
Switching on dipped headlights
– Turn the light switch to position 
.
Switching off the lights
– Turn the light switch to position 0. Switching on the fog lights*
– Pull the switch out of position 
 or 
 to the first stop. The 
symbol 
 in the light switch lights up.
Switching on the rear fog lights (vehicles with front fog lights)
– Pull the switch out of position 
 or 
 to the second stop 
⇒ . A warning lamp lights up in the control panel. 
Switching on the rear fog lights (vehicles with no front fog lights)
– Pull the light switch from position 
 to the last stop. A warning 
lamp lights up in the instrument panel.
WARNING
Never drive with just the side lights on . Risk of accident. The side lights are 
not bright enough to illuminate the road ahead and to ensure that other 
road users are able to see you. Always use your dipped headlights if it is 
dark or if visibility is poor.
Note
•
The dipped beam headlights will only  work with the ignition on. The side 
lights come on automatically when the ignition is turned off.
•
If the lights are left on after the key  has been taken out of the ignition lock, 
a buzzer will sound while the driver door remains open. This is a reminder to 
switch the lights off.
Fig. 72  Detailed view of 
instrument panel: lights, 
fog light and rear fog light 
control
AlteaXL_EN.book  Seite 109  M ontag, 2. Februar 2009  12:26 12 

Lights and visibility
110•
The rear fog light is so bright that it can dazzle drivers behind you. You 
should use the rear fog light only when visibility is very poor.
•
If you are towing a trailer equipped with a rear fog light on a vehicle with 
a factory-fitted  towing bracket, the rear fog light on the car will automatically 
be switched off.
•
The use of the lighting described here is subject to  the relevant statutory 
requirements.
•
Depending on weather conditions (very cold or wet), the front and rear 
lights and the indicators may be temporarily misted. This has no influence on 
the life expectancy of the lighting system . The lights will soon demist when 
they are switched on.
Automatic lighting*Activation
– Rotate the switch to the position “Auto”, this indication will light  up. Deactivation
– Turn the light switch to 0.
Automatic lighting
If automatic headlight control is switched on, dipped headlights are automat-
ically switched on by a light-sensitive sensor if you drive into a tunnel, for 
example.
The motorway function switches on the dipped headlights when the vehicle 
is driven at over 140 km/h for a few sec
onds and it switches the lights off 
when the vehicle is driven at less than 65 km/h for a few minutes.
The rain sensor switches on the dipped headlights when the windscreen 
wipers have been operating continuously for a few seconds and it switches 
the lights off when the continuous or  intermittent wipe is switched off for 
some minutes  ⇒page 123.
When the automatic dipped light control is connected but the dipped lights 
are off, the warning lamp 
 lights up on the light control  ⇒fig. 73 . If the 
automatic control switches on the dipped lights, the instrument and control 
lighting is also switched on.
WARNING
•
If automatic headlight control is switched on, the headlights will not be 
switched on in fog or heavy rain. Therefore, the dipped beam must be 
switched on manually.Note
•
For those vehicles with the automatic headlight system, when the key is 
removed from the ignition, the acoustic signal will only sound if the light 
control is in the position 
 or  if the vehicle is not fitted with the coming 
home function.
Fig. 73  Automatic 
lighting
AlteaXL_EN.book  Seite 110  M ontag, 2. Februar 2009  12:26 12