2009 SATURN VUE HYBRID height

Always clean the brake uid
reservoir cap and the area around
the cap before removing it. This
helps keep dirt from entering
the reservoir.
{CAUTION
With the wrong kind of uid in the
brake hydraulic system, the
brakes might not work well. This
could cause a crash. Always use
the proper brake uid.
Notice:
Using the wrong uid can
badly damage brake hydraulic
system parts. For example,
just a few drops of
mineral-based oil, such as
engine oil, in the brake
hydraulic system can damage
brake hydraulic system
parts so badly that they will
have to be replaced. Do not let
someone put in the wrong
kind of uid.
If brake uid is spilled on the
vehicle’s painted surfaces,
the paint nish can be
damaged. Be careful not to
spill brake uid on the vehicle.
If you do, wash it off
immediately. SeeWashing
Your Vehicle on page 5-69.
Brake Wear
This vehicle has disc brakes. Disc
brake pads have built-in wear
indicators that make a high-pitched
warning sound when the brake
pads are worn and new pads are
needed. The sound can come
and go or be heard all the time the
vehicle is moving, except when
applying the brake pedal rmly.
{CAUTION
The brake wear warning sound
means that soon the brakes will
not work well. That could lead to
an accident. When the brake wear
warning sound is heard, have the
vehicle serviced.Notice:Continuing to drive with
worn-out brake pads could
result in costly brake repair.
Some driving conditions or climates
can cause a brake squeal when
the brakes are rst applied or lightly
applied. This does not mean
something is wrong with the brakes.
Properly torqued wheel nuts are
necessary to help prevent
brake pulsation. When tires are
rotated, inspect brake pads for wear
and evenly tighten wheel nuts in
the proper sequence to torque
specications inCapacities and
Specifications on page 5-81.
Brake linings should always be
replaced as complete axle sets.
Brake Pedal Travel
See your dealer/retailer if the brake
pedal does not return to normal
height, or if there is a rapid increase
in pedal travel. This could be a
sign that brake service might
be required.
5-26 Service and Appearance Care
ProCarManuals.com

4. At the wall measure from the
ground upward (A) to the
recorded distance from Step 3
and mark it.
5. Draw or tape a horizontal line (B)
on the wall the width of the
vehicle at the height of the mark
in Step 4.
Notice:Do not cover a headlamp
to improve beam cut-off when
aiming. Covering a headlamp may
cause excessive heat build-up
which may cause damage to the
headlamp.6. Turn on the low-beam headlamps
and place a piece of cardboard
or equivalent in front of the
headlamp not being adjusted.
This allows only the beam of light
from the headlamp being
adjusted to be seen on the at
surface.
7. Locate the vertical headlamp
aiming screws, which are
under the hood near each
headlamp assembly.
The adjustment screw can be
turned with a E8 Torx
®socket.8. Turn the vertical aiming screw
until the headlamp beam is
aimed to the horizontal tape line.
Turn it clockwise or
counterclockwise to raise or
lower the angle of the beam.
9. Make sure that the light from the
headlamp is positioned at the
bottom edge of the horizontal
tape line. The lamp on the left (A)
shows the correct headlamp aim.
The lamp on the right (B) shows
the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for
the opposite headlamp.
5-34 Service and Appearance Care
ProCarManuals.com

CAUTION (Continued)
Underinated tires pose
the same danger as
overloaded tires. The
resulting accident could
cause serious injury.
Check all tires frequently to
maintain the recommended
pressure. Tire pressure
should be checked when
your vehicle’s tires are
cold. SeeInflation - Tire
Pressure on page 5-43.
Overinated tires are more
likely to be cut, punctured,
or broken by a sudden
impact — such as when
you hit a pothole. Keep
tires at the recommended
pressure.
Worn, old tires can cause
accidents. If the tire’s tread
is badly worn, or if your
vehicle’s tires have been
damaged, replace them.
Tire Sidewall Labeling
Useful information about a tire is
molded into its sidewall. The
example below shows a typical
passenger (p-metric) tire
sidewall.
(A) Tire Size
:The tire size is a
combination of letters and
numbers used to dene a
particular tire’s width, height,
aspect ratio, construction
type, and service description.See the “Tire Size” illustration
later in this section for more
detail.
(B) TPC Spec (Tire
Performance Criteria
Specication)
:Original
equipment tires designed to
GM’s specic tire performance
criteria have a TPC specication
code molded onto the sidewall.
GM’s TPC specications meet or
exceed all federal safety
guidelines.
(C) DOT (Department of
Transportation)
:The
Department of Transportation
(DOT) code indicates that the tire
is in compliance with the U.S.
Department of Transportation
Motor Vehicle Safety Standards.
(D) Tire Identication Number
(TIN)
:The letters and numbers
following DOT code are the
Tire Identication Number (TIN).
The TIN shows the manufacturer
and plant code, tire size, and
date the tire was manufactured.
Passenger (P-Metric) Tire
Example
Service and Appearance Care 5-39
ProCarManuals.com

The TIN is molded onto both
sides of the tire, although
only one side may have the date
of manufacture.
(E) Tire Ply Material
:The type
of cord and number of plies
in the sidewall and under
the tread.
(F) Uniform Tire Quality
Grading (UTQG)
:Tire
manufacturers are required to
grade tires based on three
performance factors: treadwear,
traction and temperature
resistance. For more information
seeUniform Tire Quality
Grading on page 5-54.
(G) Maximum Cold Ination
Load Limit
:Maximum load that
can be carried and the
maximum pressure needed to
support that load.Tire Size
The following illustration
shows an example of a typical
passenger (p-metric) vehicle
tire size.
(A) Passenger (P-Metric)
Tire
:The United States version
of a metric tire sizing system. The
letter P as the rst character in
the tire size means a passenger
vehicle tire engineered to
standards set by the U. S. Tire
and Rim Association.
(B) Tire Width
:The three-digit
number indicates the tire
section width in millimeters from
sidewall to sidewall.
(C) Aspect Ratio
:A two-digit
number that indicates the tire
height-to-width measurements.For example, if the tire size
aspect ratio is 60, as shown in
item C of the illustration, it would
mean that the tire’s sidewall is
60 percent as high as it is wide.
(D) Construction Code
:A letter
code is used to indicate the type
of ply construction in the tire.
The letter R means radial ply
construction; the letter D means
diagonal or bias ply construction;
and the letter B means
belted-bias ply construction.
(E) Rim Diameter
:Diameter of
the wheel in inches.
(F) Service Description
:These
characters represent the load
range and speed rating of the
tire. The load index represents
the load carry capacity a tire is
certied to carry. The load index
can range from 1 to 279. The
speed rating is the maximum
speed a tire is certied to carry
a load. Speed ratings range
fromAtoZ.
5-40 Service and Appearance Care
ProCarManuals.com

Tire Terminology and
Denitions
Air Pressure:The amount of
air inside the tire pressing
outward on each square inch of
the tire. Air pressure is
expressed in pounds per square
inch (psi) or kilopascal (kPa).
Accessory Weight
:This means
the combined weight of
optional accessories. Some
examples of optional
accessories are, automatic
transmission, power steering,
power brakes, power windows,
power seats, and air
conditioning.
Aspect Ratio
:The relationship
of a tire’s height to its width.
Belt
:A rubber coated layer of
cords that is located between the
plies and the tread. Cords
may be made from steel or other
reinforcing materials.Bead
:The tire bead contains
steel wires wrapped by steel
cords that hold the tire onto
the rim.
Bias Ply Tire
:A pneumatic tire
in which the plies are laid at
alternate angles less than
90 degrees to the centerline of
the tread.
Cold Tire Pressure
:The
amount of air pressure in a tire,
measured in pounds per
square inch (psi) or kilopascals
(kPa) before a tire has built
up heat from driving. See
Inflation - Tire Pressure on
page 5-43.
Curb Weight
:The weight of a
motor vehicle with standard
and optional equipment including
the maximum capacity of fuel,
oil, and coolant, but without
passengers and cargo.DOT Markings
:A code molded
into the sidewall of a tire
signifying that the tire is in
compliance with the U.S.
Department of Transportation
(DOT) motor vehicle safety
standards. The DOT code
includes the Tire Identication
Number (TIN), an alphanumeric
designator which can also
identify the tire manufacturer,
production plant, brand, and date
of production.
GVWR
:Gross Vehicle Weight
Rating. SeeLoading the Vehicle
on page 4-18.
GAWR FRT
:Gross Axle Weight
Rating for the front axle. See
Loading the Vehicle on
page 4-18.
GAWR RR
:Gross Axle Weight
Rating for the rear axle. See
Loading the Vehicle on
page 4-18.
Service and Appearance Care 5-41
ProCarManuals.com

Your dealer/retailer will know the
kind of wheel you need.
Each new wheel should have the
same load-carrying capacity,
diameter, width, offset and be
mounted the same way as the
one it replaces.
{CAUTION
Using the wrong replacement
wheels, wheel bolts, or wheel nuts
on your vehicle can be
dangerous. It could affect the
braking and handling of your
vehicle, make your tires lose air
and make you lose control. You
could have a collision in which
you or others could be injured.
Always use the correct wheel,
wheel bolts, and wheel nuts for
replacement.If you need to replace any of your
wheels, wheel bolts, or wheel
nuts, replace them only with new
Saturn original equipment parts.
This way, you will be sure to have
the right wheel, wheel bolts,
and wheel nuts for your vehicle.
Notice:The wrong wheel
can also cause problems with
bearing life, brake cooling,
speedometer or odometer
calibration, headlamp aim,
bumper height, vehicle ground
clearance, and tire clearance
to the body and chassis.
{CAUTION
Rust or dirt on a wheel, or on
the parts to which it is
fastened, can make wheel
nuts become loose after a
time. The wheel could come
off and cause a crash. When
you change a wheel, remove
any rust or dirt from places
where the wheel attaches to
the vehicle. In an emergency,
you can use a cloth or a paper
towel to do this; but be sure to
use a scraper or wire brush
later, if you need to, to get all
the rust or dirt off.
{CAUTION
Never use oil or grease on studs
or the threads of the wheel nuts.
If you do, the wheel nuts might
come loose and the wheel could
fall off, causing a crash.
5-56 Service and Appearance Care
ProCarManuals.com

Door
Automatic Door Lock.......... 2-7
Automatic Door Unlock........ 2-7
Delayed Locking................. 2-6
Locks............................... 2-6
Power Door Locks.............. 2-6
Rear Door Security Locks.... 2-7
Driver
Seat Height Adjuster........... 1-4
Driver Behavior..................... 4-2
Driver Information
Center (DIC)....................3-36
DIC Operation and
Displays.......................3-36
DIC Vehicle
Customization...............3-49
DIC Warnings and
Messages....................3-42
Driver Storage
Compartment...................2-38
Driving
At Night..........................4-12
Before a Long Trip............4-14
Defensive.......................... 4-3
Drunken............................ 4-4Driving (cont.)
Environment...................... 4-2
Highway Hypnosis............4-14
Hill and Mountain Roads....4-14
In Rain and on Wet
Roads.........................4-13
Rocking Your Vehicle to
Get it Out ....................4-17
Winter.............................4-15
Driving for Better Fuel
Economy........................... 4-3
E
EDR ..................................7-14
Electrical System
Add-On Equipment............5-75
Fuses and Circuit
Breakers......................5-75
Instrument Panel Fuse
Block...........................5-76
Power Windows and Other
Power Options..............5-75
Underhood Fuse Block......5-77
Windshield Wiper Fuses....5-75
Electronic Immobilizer
PASS-Key
®III+................2-12Electronic Immobilizer
Operation
PASS-Key
®III+................2-12
Engine
Air Cleaner/Filter...............5-15
Change Engine Oil Light....3-33
Check and Service Engine
Soon Lamp..................3-30
Coolant...........................5-20
Coolant Heater.................2-19
Coolant Temperature
Warning Light...............3-29
Drive Belt Routing.............6-13
Engine Compartment
Overview......................5-10
Exhaust...........................2-26
Oil ..................................5-11
Oil Life System.................5-14
Overheating.....................5-23
Starting...........................2-15
Entry Lighting......................3-14
Event Data Recorders..........7-14
Extender, Safety Belt............1-22
Exterior Lamps....................3-12
i-4 INDEX
ProCarManuals.com

F
Filter
Engine Air Cleaner............5-15
Finish Damage....................5-73
Fixed Mast Antenna.............3-84
Flashers, Hazard Warning....... 3-5
Flash-to-Pass........................ 3-7
Flat Tire..............................5-58
Fluid
Automatic Transmission.....5-17
Windshield Washer...........5-24
Folding Rear Seat................. 1-9
Folding Seatback,
Passenger......................... 1-7
Fuel..................................... 5-5
Additives........................... 5-5
California Fuel................... 5-5
Driving for Better
Economy....................... 4-3
Filling a Portable Fuel
Container....................... 5-8
Filling the Tank.................. 5-7
Fuels in Foreign Countries . . . 5-6
Gage ..............................3-34
Gasoline Octane................ 5-5
Gasoline Specications........ 5-5
Low Warning Light............3-34Fuel Economy Light.............3-35
Fuses
Fuses and Circuit
Breakers......................5-75
Instrument Panel Fuse
Block...........................5-76
Underhood Fuse Block......5-77
Windshield Wiper..............5-75
G
Gage
Fuel................................3-34
Speedometer...................3-24
Tachometer......................3-24
Gage, Charge/Assist.............3-35
Garage Door Opener............2-32
Gasoline
Octane............................. 5-5
Specications..................... 5-5
Glove Box...........................2-37
GM Mobility Reimbursement
Program............................ 7-5
H
Hazard Warning Flashers........ 3-5
Head Restraints..................... 1-2Headlamp
Aiming ............................5-33
Headlamps..........................5-35
Bulb Replacement.............5-35
Daytime Running Lamp.....3-13
Exterior Lamps.................3-12
Flash-to-Pass..................... 3-7
Front Turn Signal and
Parking Lamps..............5-36
Halogen Bulbs..................5-35
High/Low Beam Changer..... 3-7
Wiper Activated................3-12
Heated Seats........................ 1-5
Heater................................3-17
Engine Coolant.................2-19
Height Adjuster, Driver Seat.... 1-4
Highbeam On Light..............3-34
Highway Hypnosis................4-14
Hill and Mountain Roads.......4-14
Hood
Checking Things Under....... 5-9
Release............................ 5-9
Horn .................................... 3-5
How to Wear Safety Belts
Properly..........................1-13
INDEX i-5
ProCarManuals.com