2009 RENAULT TWINGO RS belt

75A-8
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).aUnclip the cover (1) located under the front seat.
aDisconnect the connector (2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (3) ,
-the front seat nuts (3) . Equipment required
Diagnostic tool
Tightening torquesm
front seat nuts35 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120814
121326

75A-9
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seat nuts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front seat nuts (3) .
aTorque tighten the front seat nuts (35 Nm).
aRefit the blanking covers (3) .
III - FINAL OPERATION.
aConnect the connector (2) .
aClip on the cover (1) located under the front seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).

76A-1
REAR SEAT FRAMES AND MECHANISMS
Complete rear seat: Removal - Refitting
76A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (1) from the rear seat.
aTilt the rear seatback.aTilt the rear seat assembly by pulling on the handles
(2) .
aUnlock the seat belt (3) . Tightening torquesm
rear seat bolts21 Nm
120795
120941
120942
120797

76A-2
REAR SEAT FRAMES AND MECHANISMS
Complete rear seat: Removal - Refitting
76A
aRemove:
-the seat belt (4) and (5) ,
-the rear seat.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the rear seat,
-the seat belt.
aPosition the seat normally.
aAlways replace the rear seat bolts each time they
are removed.
aRefit the rear seat bolts (1) .
aTorque tighten the rear seat bolts (21 Nm).
120796

77A-1
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and seat
belt pretensioners, Fault finding - Replacement
of components).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove the complete front seat (see 75A, Front
seat frames and mechanisms, Complete front
seat: Removal - Refitting, page 75A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the cover (1) .
aUnclip the seatback adjustment control. Special tooling required
Car. 1521Clip cr imping pliers.
Equipment required
Diagnostic tool
IMPORTANT
To prevent any accidental triggering whilst w orking
on or near a pyrotechnic component (airbags or
pretensioners), lock the airbag computer using the
Diagnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120809
120810

77A-3
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
77A
aRemove the « cover - foam » assembly.
aCut the clips (6) using a cutting tool.
aCut the clips (7) using a cutting tool.
aDetach the cover from the foam.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the cover on the foam.
aFit the clips (7) and (6) (available from the Spare
Parts Department) using the (Car. 1521).
aRefit the « cover - foam » assembly onto the seat
base frame.
aAttach the clips (5) .aLock the seat base cover tensioner.
aRefit:
-the seat base cover elastic strap (3) ,
-the elastic straps (2) securing the seatback cover.
aClip on the seatback adjustment control.
aRefit the cover (1) .
II - FINAL OPERATION.
aRefit the complete front seat (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
seat belt pretensioners, Fault finding - Replace-
ment of components).
120832
120833

77A-4
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and seat
belt pretensioners, Fault finding - Replacement
of components).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove the complete front seat (see 75A, Front
seat frames and mechanisms, Complete front
seat: Removal - Refitting, page 75A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - 1st type
aUnlock the headrest at (1) .
aRemove the headrest.
aRemove the cover (2) . Special tooling required
Car. 1521Clip cr imping pliers.
Equipment required
Diagnostic tool
IMPORTANT
To prevent any accidental triggering whilst w orking
on or near a pyrotechnic component (airbags or
pretensioners), lock the airbag computer using the
Diagnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120834
120835

77A-12
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
-the bolt (20) ,
-the headrest.
II - FINAL OPERATION.
aRefit the complete front seat (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
seat belt pretensioners, Fault finding - Replace-
ment of components).