2009 RENAULT TWINGO RS oil

21A-33
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K4M, and JR5
21A
aFit the engine wiring.
aRefit:
-the starter (see Starter: Removal - Refitting)
(16A, Starting - Charging),
-the bolts of the engine wiring channel,
-the earth strap bolt on the gearbox.
aTorque tighten the earth strap bolt on the gearbox
(44 N.m).
aConnect the reverse gear switch connector.
aClip on the reverse gear switch.
aRefit the suspended engine mounting support on the
gearbox.
aTorque tighten the support bolts for the suspend-
ed engine mounting on the gearbox (62 N.m).
aConnect the TDC sensor connector.
aRefit the engine - gearbox assembly on the.
III - FINAL OPERATION
aRefit:
-the engine - gearbox assembly (see Engine -
gearbox assembly: Removal - Refitting) (10A,
Engine and peripherals),
-the differential output seals (see 21A, Manual
gearbox, Differential output seal: Removal - Re-
fitting, page 21A-38) (21A, Manual gearbox),
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) .
-the front left-hand driveshaft (see 29A, Drive-
shafts, Front left-hand driveshaft: Removal -
Refitting, page 29A-2) ,
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),-the petrol injection computer (see Petrol injection
computer: Removal - Refitting) (17B, Petrol in-
jection),
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (12A, Fuel mixture),
-the battery (see Battery: Removal - Refitting)
(80A, Battery).
aRefill:
-the engine cooling system (see Cooling system:
Draining - Refilling) (19A, Cooling),
-the gearbox (see 21A, Manual gearbox, Manual
gearbox oils: Draining - Filling, page 21A-2) ,
-the refrigerant circuit (see Refrigerant circuit:
Draining - Filling) (62A, Air conditioning).
aRefit the engine undertray.

21A-38
MANUAL GEARBOX
Differential output seal: Removal - Refitting
JB1 or JH1 or JH3 or JR5
21A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel driveshaft (see 29A,
Driveshafts, Front right-hand driveshaft: Re-
moval - Refitting, page 29A-8) .
aDrain the gearbox (see 21A, Manual gearbox,
Manual gearbox oils: Draining - Filling, page
21A-2) .
aRemove:
-the wheel on the side concerned (see Wheel: Re-
moval - Refitting) (35A, Wheels and tyres),
-the front wheel driveshaft for the side in question
(see 29A, Driveshafts, Front left-hand drive-
shaft: Removal - Refitting, page 29A-2) or (see
29A, Driveshafts, Front right-hand driveshaft:
Removal - Refitting, page 29A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTap the base of the differential output seal using a
roll pin punch and a small hammer to rotate it in its
housing.
aRemove the differential output seal using pliers, tak-
ing care not to damage the splines on the sunwheel. Special tooling required
Bvi. 945Mandrel for fitting the sun-
wheel seal.
Bvi. 1666Tool for fitting differential
seals .
Equipment required
roll pin punch
JB1 or JH1
JH3 or JR5
JB1 or JH1
86031

21A-40
MANUAL GEARBOX
Differential output seal: Removal - Refitting
JB1 or JH1 or JH3 or JR5
21A
aThe differential output seal is refitted using the (Bvi.
1666) (4) consisting of:
-a mandrel (5) for the right-hand side,
-a mandrel (6) for the left-hand side.
aLubricate the internal surface of the differential out-
put seal.II - FINAL OPERATION
aRefit:
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) ,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aRefit:
-the front wheel driveshaft on the side concerned
(see 29A, Driveshafts, Front left-hand drive-
shaft: Removal - Refitting, page 29A-2) or (see
29A, Driveshafts, Front right-hand driveshaft:
Removal - Refitting, page 29A-8) ,
-the wheel on the side concerned (see Wheel: Re-
moval - Refitting) (35A, Wheels and tyres).
aFill the gearbox (see 21A, Manual gearbox, Manu-
al gearbox oils: Draining - Filling, page 21A-2) . JH3 or JR5
103191
109407
JB1 or JH1
JH3 or JR5

21A-44
MANUAL GEARBOX
Reverse gear switch: Removal - Refitting
JB1 or JH1 or JH3 or JR5
21A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front left-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front left-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection).
aRemove the engine undertray.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (1) from the reverse gear
switch.aRemove the reverse gear switch using the tool (Bvi.
1934) (2) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aApply some SILICONE ADHESIVE SEALANT (see
Vehicle: Parts and consumables for the repair)
(04B, Consumables - Products) to the threading of
the reverse gear switch.
aRefit the reverse gear switch using the (Bvi. 1934).
aTorque tighten the reverse gear switch (23 N.m).
aConnect the reverse gear switch connector.
II - FINAL OPERATION
aFill the gearbox (see 21A, Manual gearbox, Manu-
al gearbox oils: Draining - Filling, page 21A-2) .
aRefit the engine undertray.
aRefit:
-the front left-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection), Special tooling required
Bvi. 1934Socket for removing/refitting
reverse gear switch
Tightening torquesm
reverse gear switch23 N.m
132082
144801
Note:
Seal the housing of the reverse gear switch while
replacing the par t.

21B-1
SEQUENTIAL GEARBOX
Sequential gearbox: Precautions for the repair
D4F, and JH1
21B
I - SEQUENTIAL GEARBOX
II - SEQUENTIAL GEARBOX COMPUTER
To disconnect the computer, switch off the ignition and
wait for 1 minute.
III - ELECTRO-HYDRAULIC UNIT
Discharge the pressure accumulator using the Diag-
nostic tool before any operation on the electro-hy-
draulic unit.
Be careful not to twist the high pressure pipes when re-
moving the electro-hydraulic unit.
IV - GEAR SELECTION SENSOREquipment required
Diagnostic tool
IMPORTANT
Before any operation on the sequential system, dis-
charge the accumulator using the Diagnostic tool.
WARNING
If any operation is carried out on the electro-hydrau-
lic unit, it is essential to clean the unit using a clean-
ing product and compressed air.
Never leave the circuit open and never use a high
pressure cleaner.
WARNING
After the accumulator has been fully filled (15 sec-
onds after the ignition has been switched on): the
oil level is at the MINIMUM mark.
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.

21B-3
SEQUENTIAL GEARBOX
Sequential gearbox oil: Draining - Filling
JH1
21B
Oil capacity
DRAINING
I - DRAINING PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine undertray bolts,
-the engine undertray.
II - DRAINING OPERATION
aFit a oil recovery tray under the gearbox.aRemove:
-the gearbox drain plug (1) using the tool (Mot.
1018),
-the drain plug seal.
aLet the oil run into the oil recovery tray.
FILLING
I - FILLING PREPARATION OPERATION
aAlways replace the manual gearbox drain plug seal. Special tooling required
Mot. 10188 mm square engine drain
plug spanner.
Equipment required
oil recovery tray
Tightening torquesm
drain plug25 N.m
Gearbox type Oil capacity (in litres)
JH1 2.8
JA32.8
JA52.5
18749

21B-4
SEQUENTIAL GEARBOX
Sequential gearbox oil: Draining - Filling
JH1
21B
aPosition the slot (2) of the new seal towards the
drain plug.
aRefit the drain plug fitted with its new seal.
aTorque tighten the drain plug (25 N.m).
II - FILLING OPERATION
aRemove the filler plug (3) .aFill the gearbox using a syringe containing recom-
mended oil (see 21A, Manual gearbox, Manual
gearbox oil: Specifications, page 21A-1) (Techni-
cal Note 6012A, 04A, Lubricants) until the oil over-
flows out of the filler cap hole.
aRefit the filler plug.
III - FINAL OPERATION
aWipe any oil run-off with a cloth.
aRemove the oil recovery tray.
aRefit the engine undertray.
113764
18749
92081

21B-5
SEQUENTIAL GEARBOX
Pressure accumulator: Removal - Refitting
D4F, and JH1
21B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),
-the sequential gearbox computer (see 21B, Se-
quential gearbox, Sequential gearbox convert-
er: Removal - Refitting, page 21B-47) ,
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery),
-the petrol injection computer (see Petrol injection
computer: Removal - Refitting) (MR 411, 17B,
Petrol injection).
aDetach from the petrol injection computer mounting:
-the cooling hose,
-the sequential gearbox computer wiring harness,
-the petrol injection computer wiring harness,
-the battery wiring harness.aRemove:
-the petrol injection computer mounting nut (1) ,
-the engine wiring harness nut (2) from the petrol in-
jection computer mounting,
-the petrol injection computer mounting bolts (3) .
aRemove the engine wiring harness from the petrol
injection computer mounting.
aRemove the petrol injection computer mounting. Special tooling required
Mot. 445Oil filter strap wrench.
Equipment required
Diagnostic tool
IMPORTANT
Before carrying out any operation on the sequential
system, discharge the accumulator using the diag-
nostic tool.
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 21B, Sequential gearbox, Sequential
gearbox: Precautions for the repair, page 21B-1)
.
Note:
To discharge the accumulator and deactivate the
pump assembly pump, (see Fault finding -
Replacement of components) (MR 413, 21B,
Sequential gearbox).
122323
122322