2009 RENAULT TWINGO RS Jr5

21A-26
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K9K, and JH3 or JR5
21A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the gearbox using a component jack,
-the gearbox stud nuts,
-the gearbox lower bolts.
aTorque tighten:
-the lower gearbox bolts (44 N.m),
-the gearbox nuts and bolts (44 N.m).
aRefit the upper gearbox bolts.
aTorque tighten the gearbox upper bolts (44 N.m).
aRefit the earth strap bolt on the gearbox.
aConnect:
-the reverse gear switch connector,
-the speed and position sensor connector.
aClip the gearbox controls into place.
II - FINAL OPERATION
aRefit:
-the subframe (see Front axle subframe: Removal
- Refitting) (31A, Front axle components),
-the left-hand suspended engine mounting (see
Left-hand suspended engine mounting: Re-
moval - Refitting) (19D, Engine mounting).
aRemove the tool (Mot. 1453).
aRefit:
-the upstream strut of the catalytic converter by slid-
ing it upwards,
-the catalytic converter upstream strut bolt on the
catalytic converter.
aTighten the bolt and nut on the upstream strut of the
catalytic converter on the gearbox.
aRefit:
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the hub carrier - front left-hand and front right-hand
driveshaft assemblies (see ) (31A, Front axle com-
ponents),
-the starter (see Starter: Removal - Refitting)
(16A, Starting - Charging),-the front left-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front left-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aClip:
-the union onto the hydraulic tappet slave cylinder,
-the hydraulic clutch control pipe,
-the gearbox breather.
aBleed the clutch (see Clutch circuit: Bleed) (37A,
Mechanical component controls).
aRefit the engine management computer mounting
fitted with the engine management computer.
aFit the engine management computer wiring har-
ness.
aRefit the engine management computer wiring har-
ness nut on the engine management computer
mounting.
aFit the engine management computer mounting.
aRefit:
-the engine management computer mounting bolts,
-the engine management computer mounting nuts.
aConnect the engine management computer connec-
tors.
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
aFill up the gearbox oil (see 21A, Manual gearbox,
Manual gearbox oils: Draining - Filling, page
21A-2) .
aRefit:
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the battery (see Battery: Removal - Refitting)
(80A, Battery).

21A-30
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K4M, and JR5
21A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine undertray,
-the battery (see Battery: Removal - Refitting)
(80A, Battery),
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (12A, Fuel mixture),
-the petrol injection computer (see Petrol injection
computer: Removal - Refitting) (17B, Petrol in-
jection),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
aDrain:
-the gearbox (see 21A, Manual gearbox, Manual
gearbox oils: Draining - Filling, page 21A-2) ,
-the engine cooling system (see Cooling system:
Draining - Refilling) (19A, Cooling),
-the refrigerant circuit (see Refrigerant circuit:
Draining - Filling) (62A, Air conditioning).aRemove:
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the front left-hand driveshaft (see 29A, Drive-
shafts, Front left-hand driveshaft: Removal -
Refitting, page 29A-2) ,
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) ,
-the differential output seals (see 21A, Manual
gearbox, Differential output seal: Removal - Re-
fitting, page 21A-38) (21A, Manual gearbox),
-the engine - gearbox assembly (see Engine -
gearbox assembly: Removal - Refitting) (10A,
Engine and peripherals).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the “engine - gearbox” assembly from
theusing a workshop hoist.
aDisconnect the TDC sensor connector (1) . Equipment required
workshop hoist
Tightening torquesm
manual gearbox nuts
and bolts44 N.m
earth strap bolt on the
gearbox44 N.m
support bolts for the
suspended engine
mounting on the gear-
box62 N.m
132319

21A-31
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K4M, and JR5
21A
aRemove:
-the suspended engine mounting support bolts (2)
on the gearbox,
-the suspended engine mounting support (3) on the
gearbox.
aDisconnect the connector (4) from the reverse gear
switch.
aUnclip the reverse gear switch at (5) .aRemove the bolt (6) from the earth strap on the gear-
box.
aRemove the bolts (7) from the engine wiring harness
channel.
aMove aside the engine wiring.
aRemove the starter (see Starter: Removal - Refit-
ting) (16A, Starting - Charging).
144799
144798132321
132318

21A-32
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K4M, and JR5
21A
aRemove:
-the bolts (8) and the nuts (9) from the manual gear-
box,
-the manual gearbox.
REFITTING
I - REFITTING PREPARATION OPERATION
a
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the manual gearbox.
aTorque tighten the manual gearbox nuts and bolts
(44 N.m).
132325
132324132326
WARNING
Never operate the system when the slave cylin-
der is removed (even if it is connected to the
clutch pedal). There is a risk that the hydraulic
piston and the sla ve cylinder stop will be ejected.
WARNING
To avoid damaging the slave cylinder, do not coat
the gearbox output shaft with grease.
WARNING
Do not grease the clutch shaft splines.

21A-33
MANUAL GEARBOX
Manual gearbox: Removal - Refitting
K4M, and JR5
21A
aFit the engine wiring.
aRefit:
-the starter (see Starter: Removal - Refitting)
(16A, Starting - Charging),
-the bolts of the engine wiring channel,
-the earth strap bolt on the gearbox.
aTorque tighten the earth strap bolt on the gearbox
(44 N.m).
aConnect the reverse gear switch connector.
aClip on the reverse gear switch.
aRefit the suspended engine mounting support on the
gearbox.
aTorque tighten the support bolts for the suspend-
ed engine mounting on the gearbox (62 N.m).
aConnect the TDC sensor connector.
aRefit the engine - gearbox assembly on the.
III - FINAL OPERATION
aRefit:
-the engine - gearbox assembly (see Engine -
gearbox assembly: Removal - Refitting) (10A,
Engine and peripherals),
-the differential output seals (see 21A, Manual
gearbox, Differential output seal: Removal - Re-
fitting, page 21A-38) (21A, Manual gearbox),
-the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-8) .
-the front left-hand driveshaft (see 29A, Drive-
shafts, Front left-hand driveshaft: Removal -
Refitting, page 29A-2) ,
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),-the petrol injection computer (see Petrol injection
computer: Removal - Refitting) (17B, Petrol in-
jection),
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (12A, Fuel mixture),
-the battery (see Battery: Removal - Refitting)
(80A, Battery).
aRefill:
-the engine cooling system (see Cooling system:
Draining - Refilling) (19A, Cooling),
-the gearbox (see 21A, Manual gearbox, Manual
gearbox oils: Draining - Filling, page 21A-2) ,
-the refrigerant circuit (see Refrigerant circuit:
Draining - Filling) (62A, Air conditioning).
aRefit the engine undertray.

21A-36
MANUAL GEARBOX
Manual gearbox: Repair
JH1 or JH3 or JR5
21A
REMOVAL
I - REPAIR PREPARATION OPERATION
aRemove the gearbox (see 21A, Manual gearbox,
Manual gearbox: Removal - Refitting, page 21A-
24) .
aPosition the gearbox on the component support (see
Gearbox support equipment: Use) .
II - REMOVAL OPERATION
aRemove:
-the fifth gear housing (see 5th gear housing: Re-
moval - Refitting) ,
-the fifth gear synchroniser and pinions (see 5th
gear sprockets and synchronisers: Removal -
Refitting) ,
-the mechanism housing (see Mechanism hous-
ing: Removal - Refitting) ,
-the gearbox shafts (see Gearbox shaft: Removal
- Refitting) ,
-the differential (see Manual gearbox differential:
Removal - Refitting) .
III - REPAIR OPERATION
aStrip down the output shaft (see Output shaft:
Stripping - Rebuilding) .
aRemove:
-the differential bearings (see Manual gearbox dif-
ferential bearing: Removal - Refitting) ,
-the bearings of the mechanism housing (see
Mechanism housing bearing: Removal - Refit-
ting) ,
-the bearings of the clutch housing (see Clutch
housing bearing: Removal - Refitting) ,
-the gearbox selector shaft (see Manual gearbox
selector shaft: Removal - Refitting) .aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) to clean all of the
removed parts.
aCheck (see Manual gearbox: Check) :
-the pinions (teeth, claws, friction cone, inner wall),
-the synchroniser hubs,
-the synchroniser rings,
-the bearings.
aReplace worn or damaged parts.
REFITTING
I - REFITTING PREPARATION OPERATION
aParts always to be replaced:
-the lip seals,
-the O-rings,
-the clutch thrust bearing guide,
-the gear lock rings,
-the roll pins,
-the input and output shaft bearing circlips,
-the selector rod hub springs,
-the hydraulic clutch slave cylinder (if fitted),
-the magnet,
-the selector shaft rings,
-the lock ring of the differential,
-the differential retaining nut.
II - REFITTING OPERATION
aRefit:
-the gearbox selector shaft (see Manual gearbox
selector shaft: Removal - Refitting) ,
-the bearings of the clutch housing (see Clutch
housing bearing: Removal - Refitting) ,
-the bearings of the mechanism housing (see
Mechanism housing bearing: Removal - Refit-
ting) ,
-the differential bearings (see Manual gearbox dif-
ferential bearing: Removal - Refitting) .
aRebuild the output shaft (see Output shaft: Strip-
ping - Rebuilding) . IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see Manual gearbox: Precautions for the
repair) .

21A-37
MANUAL GEARBOX
Manual gearbox: Repair
JH1 or JH3 or JR5
21A
III - REMOVAL OPERATION
aRefit:
-the differential (see Manual gearbox differential:
Removal - Refitting) ,
-the gearbox shafts (see Gearbox shaft: Removal
- Refitting) .
aAdjust the shafts (see Gearbox shaft: Adjustment)
if replacing a shaft or housing.
aRefit:
-the mechanism housing (see Mechanism hous-
ing: Removal - Refitting) ,
-the fifth gear synchroniser and pinions (see 5th
gear sprockets and synchronisers: Removal -
Refitting) ,
-the fifth gear housing (see 5th gear housing: Re-
moval - Refitting) .
IV - FINAL OPERATION
aRemove the gearbox from the component support
(see Gearbox support equipment: Use) .
aRefit the gearbox (see 21A, Manual gearbox, Man-
ual gearbox: Removal - Refitting, page 21A-24) .

21A-38
MANUAL GEARBOX
Differential output seal: Removal - Refitting
JB1 or JH1 or JH3 or JR5
21A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel driveshaft (see 29A,
Driveshafts, Front right-hand driveshaft: Re-
moval - Refitting, page 29A-8) .
aDrain the gearbox (see 21A, Manual gearbox,
Manual gearbox oils: Draining - Filling, page
21A-2) .
aRemove:
-the wheel on the side concerned (see Wheel: Re-
moval - Refitting) (35A, Wheels and tyres),
-the front wheel driveshaft for the side in question
(see 29A, Driveshafts, Front left-hand drive-
shaft: Removal - Refitting, page 29A-2) or (see
29A, Driveshafts, Front right-hand driveshaft:
Removal - Refitting, page 29A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTap the base of the differential output seal using a
roll pin punch and a small hammer to rotate it in its
housing.
aRemove the differential output seal using pliers, tak-
ing care not to damage the splines on the sunwheel. Special tooling required
Bvi. 945Mandrel for fitting the sun-
wheel seal.
Bvi. 1666Tool for fitting differential
seals .
Equipment required
roll pin punch
JB1 or JH1
JH3 or JR5
JB1 or JH1
86031