2009 RENAULT TWINGO RS battery

41C-11
SIDE LOWER STRUCTURE
Sill panel closure panel: Description
41C
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121246
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41C-14
SIDE LOWER STRUCTURE
Sill panel reinforcement: Description
41C
III - POSITIONING OF THE NEARBY ELECTRICAL
EARTHS
121246
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41C-16
SIDE LOWER STRUCTURE
Sill panel stiffener: Description
41C
Section B
3 - Complete replacementIII - POSITIONING OF LOCAL ELECTRICAL
EARTHS
120972
120975
121246
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41D-3
REAR LOWER STRUCTURE
Rear floor: Description
41D
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121249
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41D-9
REAR LOWER STRUCTURE
Rear side member: Description
41D
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121249
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41D-12
REAR LOWER STRUCTURE
Rear floor front cross member: Description
41D
There is only one way of replacing this part:
-partial replacement.
I - COMPOSITION OF THE SPARE PARTII - PART IN POSITION
Partial replacement
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121515
121011
No. Description Type Thic-
kness
(mm)
(1) Cross member HLE 1.5
(2) Rear seat runner
front stiffenerMild
steel1.2
(3) Front centre
reservoir moun-
tingHLE 1.2
121227
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

41D-17
REAR LOWER STRUCTURE
Rear towing eye: Description
41D
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121249
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

42A-17
FRONT UPPER STRUCTURE
Scuttle side panel: Description
42A
This cut gives access to the front wheel arch.
III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
120981
IMPORTANT
For welded connections in three thicknesses, the
spot welds on the part replaced should be made in
the same place as for the original joint to retain its
mechanical proper ties.
121245
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.