2009 RENAULT TWINGO RS trip computer

52A-6
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially open the sunroof mobile panel.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the sunroof console (see Sunroof switch: Remo-
val - Refitting) (MR 411, 87D, Electric window win-
ders - Sunroof),
-the sun visors (see 57A, Interior equipment, Sun
visor: Removal - Refitting, page 57A-16) ,
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear bench seatback (depending on equipment
level) (see Rear bench seatback: Removal - Re-
fitting) (MR 412, 76A, Rear seat frames and run-
ners),
-the rear parcel shelf side trim panels (see Rear
parcel shelf side trim: Removal - Refitting) (MR
412, 71A, Body internal trim),-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the cross member mounting of the sunroof sun vi-
sor (see 52A, Non-side opening element mecha-
nisms, Sunroof sun visors: Removal - Refitting,
page 52A-15) ,
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aRemove:
-the bolts (1) ,
-the sunroof computer mounting.
aDisconnect the sunroof computer connectors. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121396

52A-7
NON-SIDE OPENING ELEMENT MECHANISMS
Sunroof operating mechanism: Removal - Refitting
52A
aRemove:
-the bolts (2) ,
-the sunroof console mounting.
aProtect the vehicle interior.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aProtect the sunroof frame using masking tape.
ainsert the threading needle preferably at the front left
or right of the sunroof operating mechanism.
aCut the cement bead (this operation requires two
people).
aRemove the sunroof operating mechanism using the
specific support (x2):
-Support: PARV 202,
-arch sets: APARV 200 ESP.
REFITTING
I - REFITTING PREPARATION OPERATION
aFor preparation and bonding see Technical Note
560A, General procedure for bonding windows
and sunroof.
aPosition:
-the two centring guides on the sunroof operating
mechanism,
-the positioning shims on the periphery of the sun-
roof operating mechanism.
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the cement bead at the interior roof panel
surround or on the sunroof cassette according to the
marking.
aBond the sunroof mechanism using the special sup-
port (this operation requires two people).
aCentre the sunroof operating mechanism with in-
dexing guides with an operator inside the vehicle.
aCheck that the sunroof operating mechanism posi-
tioning shims make contact with the roof.
aRemove the two indexing guides 30 minutes after
bonding the sunroof operating mechanism.
III - FINAL OPERATION.
aConnect the sunroof computer connectors.
aRefit:
-the bolts (2) ,
-the sunroof console mounting,
-the bolts (1) ,
-the sunroof computer mounting,
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) ,
-the cross member mounting of the sunroof sun vi-
sor (see 52A, Non-side opening element mecha-
nisms, Sunroof sun visors: Removal - Refitting,
page 52A-15) ,
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
121715
WARNING
When cutting the cement bead, make sure that
the wire passes between the panel and the posi-
tioning shims on the edge of the sunroof opera-
ting mechanism.

54A-7
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aProtect:
-the sunroof's fixed window surround and the rear
section of the roof using masking tape,
-the inside of the vehicle.II - REMOVAL OPERATION FOR PART
CONCERNED
aCut the cement bead; this operation requires two
people.
aRemove the fixed window from the sunroof.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the new shims on the sunroof operating me-
chanism.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the sunroof fixed window using the specific
support (this operation requires two people):
-Support: PARV 202,
-set of arch supports: APARV 200 ESP. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121153

54A-8
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
Respect the clearances and shut lines
aObserve the 6 mm clearance between the sunroof
fixed window (1) and the sunroof mobile panel (2) .
aThe sunroof's fixed window (1) should be slightly
lower than its mobile panel (2) .
aArrange the lateral clearances so that they are
equal.
III - FINAL OPERATION.
aRefit:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
113525