2009 RENAULT TWINGO RS air condition

62B-86
MR-413-X44-62B000$874_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 8
CONTINUED 7
2
With the engine warm and passenger compartment
ventilation operating, vary the position of the mixing
flap from the maximum hot position to the maximum
cold position and check subjectively that there is a
difference in temperature.
Is a difference in temperature noted?
YES
E
NOCarry out a conformity check on the mixing
motor (PR012 Mixing flap position). If the
conformity check does not reveal any faults,
look for a mechanical fault on the mixing flap
(condition of the motor ’s notched sector, flap
jammed inside the unit, etc.).
Is the fault still present?
YES NO
End of fault finding
procedure.
Check the cold loop by checking the condition of the pipes and ensuring that the air conditioning system
does not have any refrigerant leaks (see Technical Note 6001A, Air conditioning, 62A, Air conditioning,
Air conditioning: Check). Repair the faulty pipes or components.
Top up the refrigerant (see MR 411 Mechanical, 62A, Air conditioning, Refrigerant circuit:
Draining - Filling).
Is the fault still present?
NO YES
End of fault finding procedure. Replace the air conditioning compressor.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62B-87
MR-413-X44-62B000$874_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 9 Too much cold air
NOTESOnly deal with this customer complaint after a full check with the diagnostic tool
(fault reading and configuration checks).
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, NEW TWINGO.
With the engine running at idle speed and air conditioning switched off (AC button not pressed and no AUTO
mode), check that the air conditioning compressor clutch is not engaged.
Is the air conditioning compressor
clutch engaged?NO
YES
With the engine stopped, check that the compressor clutch electric control operates correctly, using the
diagnostic tool to run command AC180 Air conditioning compressor relay (injection command mode menu).
–During the command, connection 38R of component 171 must be supplied with + 12 V.
–After the command, connection 38R of component 171 must no longer be supplied with + 12 V.
Is the connection still supplied with + 12 V after the command?
YES NO
Check the continuity and insulation from + 12 V of
connection 38R between components 171 and 584.Check that the air conditioning compressor clutch is
not jammed (mechanical fault).
Is the connection OK? Is the clutch still engaged?
NO YES YES
If there is a repair procedure
(see Technical Note 6015A,
Repairing electrical wiring,
Wiring: Precautions for repair),
repair the wiring, otherwise
replace it.With the vehicle ignition off, check
that the compressor clutch relay is
not “jammed”, by checking the
continuity between connection
38R and connection AP3 of
component 584.
Is the continuity present?
NO
Apply the fault finding procedure for
command AC180 Air conditioning
compressor relay (see 13B Diesel
injection or 17B Petrol injection).
Is the fault still present?
Replace the air conditioning
compressor (see MR 411,
Mechanical, 62A, Air
conditioning, Compressor:
Removal - Refitting).
YES Replace the air
conditioning
compressor clutch
relay.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62B-88
MR-413-X44-62B000$874_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 9
CONTINUED
With the engine warm and passenger compartment
ventilation operating, vary the position of the mixing
flap from the maximum cold position to the
maximum hot position and check subjectively that
there is a difference in temperature.
Is a difference in temperature noted?
YES
Using the diagnostic tool statuses and parameters
screen (cold loop sub-function), check that the
temperature signals are consistent (no sensor
deviation resulting in incorrect measurement).
–Using parameters PR002 Exterior temperature,
PR064 Coolant temperature and PR001
Interior temperature.
Are the temperature signals consistent?
YES
Check the refrigerant fluid (see Technical Note
6001A, Air conditioning, 62A, Air conditioning,
Air conditioning: Check).
NOCarry out a conformity check on the
mixing motor (PR012 Mixing flap
position). If the conformity check does
not reveal any faults, look for a
mechanical fault on the mixing flap
(condition of the motor ’s notched sector,
flap jammed inside the unit, etc.).
NOCarry out a conformity check:
–For the coolant temperature sensor, see
13B, Diesel injection, Fault summary
table or 17B Petrol injection, Fault
summary table.
–For the exterior temperature sensor,
see 87B, Passenger compartment
connection unit, Fault summary
table.
–For the interior temperature sensor, see
62B, Climate control, Fault summary
table.
Replace any faulty components.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62B-89
MR-413-X44-62B000$920_eng.mif
V1
62B
CLIMATE CONTROL
Diagnostic - Fault finding chart
ALP 10 Inefficient rear screen de-icing/demisting
NOTESCarry out this conformity check after a full check using the diagnostic tool
(fault reading, especially UCH and injection faults and configuration checks).
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, NEW TWINGO.
Special notes:
Check that the inside of the windows are not greasy as this reduces the efficiency of
the de-icing.
Note:
The de-icing control is only authorised when the engine is running to save power.
The rear screen de-icer control is activated by pressing the de-icing button at the
bottom of the climate control panel in manual mode (with time delay and rear-view
mirror de-icer).
Ensure that there are no water leaks in the passenger compartment which would significantly increase the
moisture and reduce the effectiveness of the demisting function (see ALP 12 if the fault is noted).
Is the fault still present?
YES NO
Check that the UCH is correctly configured by viewing the configuration reading LC013 Type of air conditioning.
Reconfigure the UCH if necessary.
Check that the UCH receives the signal about the
status and operation of the engine. In the Cold Loop
screen, status ET142 "engine operating phase"
should display RUNNING.
Is status ET142 RUNNING?
YES
End of fault finding procedure.
NOCarry out fault finding on the UCH
(interpretation of status ET142) and on the
multiplex network.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

Vdiag No.: 44
MR-413-X44-62B000$920_eng.mif

62B-91
MR-413-X44-62B000$920_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 11 Unpleasant odours in the passenger compartment
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check that the cabin filter is not blocked or damaged
(see MR 411 Mechanical, 61A, Heating, Cabin filter:
Removal - refitting).
Replace it if necessary.
Is the fault still present?
YES
Check that the condensate (water from the evaporator)
drain ring is not obstructed (beneath the body).
Repair if necessary.
Is the fault still present?
YES
Check the sealing of the heating unit in relation to the
engine compartment:
- Foam seal on the heater matrix coolant pipes fitted and
in good condition.
- Rubber seal on the radiator tank fitted and in good
condition (seal under the bonnet separating the engine
compartment from the windscreen aperture).
- Drain valve on the radiator tank fitted and in good
condition.
Repair if necessary.
Is the fault still present?
YES
Remove the passenger compartment filter to apply air
conditioning system cleaner using an extension piece on
the evaporator. Spray the entire contents of the aerosol.
Leave the product to work for 15 minutes.
NOEnd of fault finding procedure.
NOEnd of fault finding procedure.
NOEnd of fault finding procedure.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
CLIM_V44_ALP11

62B-92
MR-413-X44-62B000$920_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 12 Water is present in the passenger compartment
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Pressurise the cooling circuit.
Is there any coolant leaking into the vehicle?
NO
Check that the evaporator evacuation ring is not
blocked (under the body).
Repair if necessary.
Is the fault still present?
YES
Make sure that the scuttle panel (under the windscreen aperture) is not filled with water. If it is, check that the
drain valve is fitted to the scuttle panel and is in good condition.
Replace the valve if necessary.
Has the customer just washed the vehicle?
YES
Explain to the customer that when washing the car
using a hose pipe, the water jet must not be left for
too long on the air inlet in the scuttle panel (on the
bonnet).
YES Repair.
NOEnd of fault finding procedure.
NO End of fault finding procedure.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
CLIM_V44_ALP12

62B-93
MR-413-X44-62B000$920_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 13 Lighting fault on the control panel in night mode
NOTESOnly consult this customer complaint after a complete check of the multiplex
network and the air conditioning with the diagnostic tool.
Special notes:
With the ignition on, the control panel screen is permanently on but the panel buttons
only light up when the side lights are switched on.
Note:
If the exterior temperature sensor is faulty, the climate control computer is
activated 5 seconds after the ignition is switched on (the UCH performs fault
finding on the exterior temperature sensor).
Use the Wiring Diagram Technical Note for the New Twingo.
Is the fault shared with other components (first row cigarette lighter, radio, multifunction display, cruise control/
speed limiter on off switch, etc.)
YES NO
Switch on the ignition and the side lights.
Using the diagnostic tool and the conformity
check, check that the lighting dimmer is operating
correctly using parameter PR122 NIGHT TIME
LIGHTING LEVEL.
Does the parameter vary?
YES
Check the connection and condition of the
connector of component 419.
If there is a repair method (see Technical Note
6015A, Electrical wiring repair, Wiring: Repair
precautions), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
NOCarry out a fault finding procedure of the
instrument panel.
Run a multiplex network test (see 88B,
Multiplex).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
CLIM_V44_ALP13

62B-94
MR-413-X44-62B000$920_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 13
CONTINUED
Switch off the ignition and turn off the side lights.
Disconnect the connectors of components 101, 1081, 1222, 1391, 319, 184, 1390, 261, 653, 1016 and 419 of
connection LPD (see Wiring Diagrams Technical Note, Twingo 2 passenger compartment fuse board,
component code 1016, connection code LPD).
Check the insulation, continuity and the absence of interference resistance of connection LPD between
components 419 and 1016.
If the connection is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for the
repair), repair the wiring, otherwise replace the wiring.
YES
If the check does not reveal any electrical faults, check the conformity of the components on connection LPD
(component in short circuit, etc.)
Check the condition and position of fuse F42 (10 A) in the passenger compartment fuse box.
Consult section 81C Fuses.
Repair if necessary.
Is the fault still present?
YES
Contact the Techline.
NOEnd of fault finding procedure.
AFTER REPAIRCarry out a complete check with the diagnostic tool.