2009 RENAULT TWINGO RS engine oil

10A-50
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
K9K
10A
REMOVAL
I - OPERATION FOR REMOVAL OF PART
CONCERNED
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove the sump (see 10A, Engine and cylinder
block assembly, Lower cover: Removal - Refit-
ting, page 10A-6) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the oil pump bolts (1) ,
-the oil pump.
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck for oil pump centering rings on the cylinder
block.II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the oil pump,
-the oil pump bolts.
aTorque tighten the oil pump bolts (25 Nm).
III - FINAL OPERATION.
aRefit the sump (see 10A, Engine and cylinder
block assembly, Lower cover: Removal - Refit-
ting, page 10A-6) .
aTop up the engine oil (see 10A, Engine and cylin-
der block assembly, Engine oil: Draining - Refill-
ing, page 10A-22) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ). Tightening torquesm
oil pump bolts25 Nm
120313

10A-51
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) .
aRemove:
-the oil filter (see 10A, Engine and cylinder block
assembly, Oil filter: Removal - Refitting, page
10A-29) ,
-the dipstick,
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) .
aRefit:
-the upper timing cover,
-the upper timing cover bolts (1) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) .
aRemove the lower engine support tool (Mot. 1379).
aRemove the sump (see 10A, Engine and cylinder
block assembly, Lower cover: Removal - Refit-
ting, page 10A-6) . Special tooling required
Mot. 1379Engine suppor t tool for cylin-
der head oper ations.
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1374Oil pump seal e xtractor.
Mot. 1626Tool for fitting the PTFE
cr ankshaft seal, timing end.
Tightening torquesm
oil pump bolts10 N.m
109740

10A-52
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
aDisconnect the oil pressure sensor connector.
aDisconnect the oil pressure sensor connector (1) .
aFit hose clamps (Ms. 583) onto the oil-coolant heat
exchanger hoses (2) .
aRelease the clips (3) using the (Mot. 1448).
aDisconnect the oil cooler hoses.
aRemove the timing sprocket. D4F, and 772 – D7F
120772
D4F, and 780 or 782
121725
121726

10A-53
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
aRemove the crankshaft output seal by turning the
(Mot. 1374).
aRemove the crankshaft output seal by turning the
bolt of the (Mot. 1374).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the oil pump strainer bolts,
-the oil pump strainer,
-the oil pump bolts,
-the oil pump.
18645-1
18645-2
18646

10A-54
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
REFITTING
I - REFITTING PREPARATION OPERATION
aClean the joint faces (see Vehicle: Parts and con-
sumables for the repair) (04B, Consumables -
Products).
aparts always to be replaced: engine oil strainer
seal.
aparts always to be replaced: Crankshaft seal on
timing end.
aApply a BEAD OF SILICONE ADHESIVE SEAL-
ANT (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products) with a
width of 1.3 mm to ensure the sealing of the oil
pump.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the oil pump, aligning the oil pump drive points with
the flat surfaces of the crankshaft,
-the oil pump bolts.aTighten to torque and in order the oil pump bolts
(10 N.m).
aRefit:
-the oil pump strainer with a new seal,
-the oil pump strainer bolts.
III - FINAL OPERATION
aScrew the threaded rod of the (Mot. 1626) into the
crankshaft.
18718
WARNING
To ensure proper sealing, the gasket surfaces
must be clean, dry and not greasy (avoid any fin-
ger marks).
18646
20784

10A-55
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
aFit the protector fitted with a new crankshaft output
seal on the crankshaft, taking care not to touch the
seal.
aFit the cover and the collar nut of the (Mot. 1626).aTighten the collar nut until the cap touches the
crankshaft closure panel.
20782
2078320781
20780

10A-56
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
D4F or D7F
10A
aRemove:
-the nut,
-the cover,
-the guard,
-the threaded rod.
aConnect the oil-coolant heat exchanger hoses.
aPut the clips (3) in place using the (Mot. 1448).
aRemove the hose clamps (Ms. 583) from the oil-wa-
ter heat exchanger hoses.
aConnect the oil pressure sensor connector.
aRefit:
-the timing sprocket,
-the sump (see 10A, Engine and cylinder block
assembly, Lower cover: Removal - Refitting,
page 10A-6) .
aFit the lower engine support tool (Mot. 1379).
aRemove:
-the right-hand suspended mounting support bolts,
-the right-hand suspended mounting support,
-the upper timing cover bolts,
-the upper timing cover.aRefit:
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) .
aRemove the lower engine support tool (Mot. 1379).
aRefit:
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the engine undertray,
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the dipstick,
-the oil filter (see 10A, Engine and cylinder block
assembly, Oil filter: Removal - Refitting, page
10A-29) .
aTop up the engine oil (see 10A, Engine and cylin-
der block assembly, Engine oil: Draining - Refill-
ing, page 10A-22) .
aTop up the coolant level (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
20779
D4F, and 780 or 782

10A-57
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil pump: Removal - Refitting
K4M
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the engine undertray.
aDrain the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) .
aRemove:
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the rear engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents).
aRemove the sump (see 10A, Engine and cylinder
block assembly, Lower cover: Removal - Refit-
ting, page 10A-6) .II - REMOVAL OPERATION
aRemove:
-the oil pump bolts (1) ,
-the oil pump.
REFITTING
I - REFITTING OPERATION
aPosition the oil pump pinion on the chain.
aRefit the oil pump.
aTorque tighten the oil pump bolts (25 N.m).
II - FINAL OPERATION
aRefit the sump (see 10A, Engine and cylinder
block assembly, Lower cover: Removal - Refit-
ting, page 10A-6) .
aRefit:
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the rear engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion), Tightening torquesm
oil pump bolts25 N.m
128799