2009 RENAULT TWINGO RS camshaft

11A-62
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aPosition the (Mot. 1490-01) (30) on the camshaft
pulleys.
aTorque tighten:
-and angle tighten the exhaust camshaft pulley
nut (30 N.m + 84˚),
-the camshaft dephaser pulley bolt (100 N.m).
aRefit the dephaser pulley bolt cover.
aRemove:
-the timing flap from the lower timing cover,
-the (Mot. 1496),-the TDC setting pin (Mot. 1489),
-the (Mot. 1490-01).
4 - Checking the tension
aRotate the crankshaft twice in a clockwise direction,
on the timing end, before aligning the marks (on the
camshaft dephaser) already made by the operator.
aScrew in the TDC setting pin (Mot. 1489).
aMove the crankshaft slowly and smoothly to rest on
the TDC setting pin.
aRemove the TDC setting pin (Mot. 1489).
103265
109052

11A-63
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aCheck through the lower timing cover window that
the adjustable index (31) is opposite the notch (32) ,
if this is not the case:
-loosen the timing tensioning roller nut by up to one
turn while holding the eccentric with a 6 mm Allen
key,
-gradually move the adjustable index marker (31)
opposite the mark (32) turning the eccentric cam
(33) clockwise.
aTorque tighten the timing tension wheel nut (27
N.m).5 - Checking the timing
aEnsure that the index and the notch on the timing
tensioning roller are in the correct position before
checking the timing.
aScrew in the TDC setting pin (Mot. 1489).
aBring the crankshaft slowly and smoothly to rest
against the TDC setting pin (Mot. 1489).
aPosition (without forcing) the camshaft setting tool
(Mot. 1496) fitted with the (Mot. 1750) (the camshaft
end grooves must be horizontal and offset towards
the bottom).
aRemove:
-the timing tool (Mot. 1496) fitted with the (Mot.
1750),
-the TDC setting pin (Mot. 1489).
109051
103263
14490
Note:
The timing adjustment and tensioning operation
must be repeated if the camshaft setting tool
does not engage .

11A-64
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aRefit the lower timing cover flap, checking that the
locating pin (34) fits properly in the notch (35) .
III - FINAL OPERATION
aRefit:
-a new inlet camshaft plug using the (Mot. 1487),
-a new exhaust camshaft plug using the (Mot.
1488),
-the lifting eye.
aClip the wiring onto the lifting eye.aPlace a drop of SILICONE ADHESIVE SEALANT
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products) on the thread
of the TDC setting pin plug.
aTorque tighten the TDC setting pin plug (20 N.m).
aRefit the upper timing cover.
aTorque tighten:
-the upper timing cover bolts (41 N.m),
-the upper timing cover nuts (41 N.m).
aPosition the wiring of the upstream oxygen sensor.
aAttach the upstream oxygen sensor wiring.
aConnect the upstream oxygen sensor connector.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting.
aTorque tighten:
-the rear suspended engine reinforcement bolt
(105 N.m),
-the rear suspended engine mounting bolt on
the rear suspended engine mounting support
(105 N.m),
-the rear suspended engine mounting bolt on
the subframe (105 N.m).
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the throttle valve (see 12A, Fuel mixture, Throttle
valve: Removal - Refitting, page 12A-20) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
109052
14890

11A-70
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
D4F, and 772
11A
II - REFITTING OPERATION FOR PART
CONCERNED
aApply a bead (1) of SILICONE ADHESIVE SEAL-
ANT (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products) to the
camshaft bearings 1 and 5, as well as around the
rocker cover rear bolts.
aFit the rocker cover with a new gasket.aTighten the rocker cover bolts in order.
III - FINAL OPERATION
aRefit:
-the ignition coil (see 17A, Ignition, Coils: Remov-
al - Refitting, page 17A-1) ,
-the inlet distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
aClip on the rocker cover electric wiring harnesses.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
18441
20005
110422

11A-74
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
D4F, and 780 or 782 or 784
11A
II - REFITTING OPERATION FOR PART
CONCERNED
aApply beads (1) of MASTIXO (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products) around the rocker cover rear bolts
(lower bolts, exhaust side) and on camshaft bearing
no.5.
aFit the new rocker cover seal, starting with bearing
No. 5, then gradually insert the seal studs as the
rocker cover fits into the groove.aRefit:
-the rocker cover fitted with a new seal,
-the rocker cover bolts.
aPretighten to torque and in order the rocker cover
bolts (initial torque) (5 N.m).
aTorque tighten in order the rocker cover bolts (13
N.m).
III - FINAL OPERATION
aFit the brake servo vacuum pipe.
aConnect the brake servo vacuum pipe.
aFit the fuel vapour rebreathing pipes.
aConnect the fuel vapour rebreathing circuit unions:
-on the inlet distributor,
-on the air filter box outlet air pipe.
aFit the oil vapour rebreathing circuit.
aConnect the oil vapour rebreathing circuit unions:
-on the rocker cover,
-on the air filter box outlet air pipe,
-to the inlet distributor.
aRefit:
-the ignition coil (see 17A, Ignition, Coils: Remov-
al - Refitting, page 17A-1) ,
-the filler neck,
-the filler neck bolt,
-the heat shield,
-the heat shield bolts.
aTorque tighten the heat shield bolts (8 N.m).
18441
WARNING
Applying excess sealant could cause it to be
squeezed out when parts are tightened. A mix-
ture of sealant and fluid could damage certain
components (engine, radiator, etc.).
121026

11A-76
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
K4M
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the coils (see 17A, Ignition, Coils: Removal - Re-
fitting, page 17A-1) ,
-the throttle valve (see 12A, Fuel mixture, Throttle
valve: Removal - Refitting, page 12A-20) ,
-the inlet distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the oil decanter (see 11A, Top and front of en-
gine, Oil decanter: Removal - Refitting, page
11A-147) ,
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) ,
-the camshaft dephaser (see 11A, Top and front of
engine, Camshaft dephaser: Removal - Refit-
ting, page 11A-135) ,
-the camshaft seals on the timing end (see 11A,
Top and front of engine, Camshaft seal, timing
end: Removal - Refitting, page 11A-138) . Tightening torquesm
rocker cover bolts 22,
23, 20 and 13 (initial
torque)8 N.m
rocker cover bolts 1 to
12, 14 to 19 and 21 to
2413 N.m
rocker cover bolts 22,
23, 20 and 1313 N.m
camshaft sensor bolt8 N.m
camshaft dephaser
solenoid valve bolt10 N.m

11A-77
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
K4M
11A
aDisconnect the connector (1) from the camshaft po-
sition sensor.
aRemove:
-the bolt (2) from the camshaft position sensor,
-the camshaft position sensor,
-the camshaft position sensor seal.aDisconnect the camshaft dephaser solenoid valve
connector.
aRemove:
-the bolt (3) from the camshaft dephaser solenoid
valve sensor,
-the camshaft dephaser solenoid valve,
-the camshaft dephaser seal.
132391132443

11A-78
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
K4M
11A
II - REMOVAL OPERATION
aRemove the rocker cover bolts.
aDetach the rocker cover using a screwdriver.
aRemove the rocker cover.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the camshaft position sensor seal,
-the camshaft dephaser solenoid valve seal.
aUse SUPER CLEANER FOR JOINT FACES (see
Vehicle: Parts and consumables for the repair)
(04B, Consumables - Products) to clean:
-the rocker cover joint face if it is to be re-used,
-the cylinder head joint face.aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to degrease:
-the rocker cover joint face if it is to be re-used,
-the cylinder head joint face.
14497-5
Note:
The rocker cover bolts are not the same length;
mark their positions.
WARNING
Do not scrape the joint faces of the aluminium,
any damage caused to the joint face will result in
a risk of leaks.
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).