2009 RENAULT TWINGO RS brake

19A-45
COOLING
Water chamber: Removal - Refitting
K9K
19A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the thermostat to the water chamber.
aRefit:
-a new water chamber seal,
-the water chamber.
aTorque tighten the water chamber bolts (10 N.m).
III - FINAL OPERATION
aConnect the cooling hoses on the water chamber.
aPosition the cooling hose clips on the water chamber
using the tool (Mot. 1448).
aClip on the cooling hose of the coolant-oil heat ex-
changer.
aConnect the intercooler air outlet pipe on the side of
the damper valve.
aTorque tighten the intercooler air outlet pipe clip
at the damper valve end (5.5 N.m).
aConnect the brake servo vacuum pipe.
aClip:
-the turbocharging pressure regulator vacuum pipe,
-the vacuum pipe from the brake servo.
aConnect the turbocharging pressure regulator vacu-
um pipe.
aRefit the nuts of the air hoses on the lifting eye.
aConnect the intercooler air inlet pipe at the turbo-
charger end.
aClip on the intercooler air inlet pipe clip at the turbo-
charger end.
aFill the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-9) .
aRefit the engine cover. K9K, and 718

19B-24
EXHAUST
Expansion chamber: Removal - Refitting
D4F, and 780 or 782
19B
aCut the exhaust pipe (see 19B, Exhaust, Exhaust:
Precautions for the repair, page 19B-8) in the area
designated to be cut (see ) .
aRemove:
-the expansion chamber rubber mounting bush bolt
from the body,
-the expansion chamber,
-the rubber mounting bush bolt from the expansion
chamber,
-the expansion chamber rubber mounting bush.
REFITTING THE EXPANSION CHAMBER
I - REMOVAL OPERATION FOR PART
CONCERNED
aRefit:
-the expansion chamber rubber mounting bush,
-the expansion chamber rubber mounting bush bolt.
aFit the expansion chamber.
aAttach the expansion chamber to the vehicle using
the expansion chamber rubber mounting bush bolt.
aFit a new After-Sales sleeve (see 19B, Exhaust, Ex-
haust: Precautions for the repair, page 19B-8) .
aTighten the exhaust trunking.
aTighten the expansion chamber rubber mounting
bush bolt on the body.
aRefit a new clip between the front section of the ex-
pansion chamber and the expansion chamber.
aTighten the clip between the front section of the ex-
pansion chamber and the expansion chamber.II - FINAL OPERATION
aCheck the following and deal with if necessary:
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
aStart the vehicle.
aCheck that there are no leaks and deal with them if
necessary.
Note:
If the rubber mounting bushes are damaged,
mark the position of the support on the body,
then replace the « support - rubber mounting
bush » assembly.
Note:
If replacing the rubber mounting bush, spray the
inside of the rubber mounting bush with BRAKE
CLEANER (see Vehicle: Parts and consum-
ables for the repair) (MR 411, 04B, Consum-
ables - Products) to facilitate fitting.

19B-29
EXHAUST
Intermediate pipe: Removal - Refitting
K9K
19B
REFITTING THE INTERMEDIATE PIPE
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the rubber mounting bush of the intermediate pipe,
-the rubber mounting bush bolt on the intermediate
pipe.
aFit the intermediate pipe.
aAttach the intermediate pipe to the vehicle using the
intermediate pipe rubber mounting bush bolt.
aFit a new After-Sales sleeve and follow the instruc-
tions (see 19B, Exhaust, Exhaust: Precautions
for the repair, page 19B-8) .
aRefit a new clip between the front section of the in-
termediate pipe and the intermediate pipe.
aCheck the following and deal with if necessary:
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
aStart the engine.
aCheck that there are no leaks and deal with them if
necessary.Note:
If replacing the rubber mounting bush, spray the
inside of the rubber mounting bush with BRAKE
CLEANER ( (see Vehicle: Parts and consum-
ables for the repair) ) in the form of an aerosol
spray to facilitate fitting.

19B-30
EXHAUST
Intermediate pipe: Removal - Refitting
D4F, and 772 – D7F
19B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the clip between the catalytic converter and
the intermediate pipe.
aRemove the intermediate pipe
aCut the exhaust pipe (see 19B, Exhaust, Exhaust:
Precautions for the repair, page 19B-8) in the des-
ignated area to be cut (see ) .
aRemove:
-the intermediate pipe rubber mounting bush bolt on
the body,
-the connector pipe,
-the rubber mounting bush bolt on the intermediate
pipe,
-the intermediate pipe rubber mounting bush.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the rubber mounting bush of the intermediate pipe,
-the rubber mounting bush bolt on the intermediate
pipe.
aFit the intermediate pipe.
aAttach the intermediate pipe to the vehicle using the
intermediate pipe rubber mounting bush bolt.
aFit a new After-Sales sleeve and follow the instruc-
tions (see 19B, Exhaust, Exhaust: Precautions
for the repair, page 19B-8) .
aRefit a new clip between the front section of the in-
termediate pipe and the intermediate pipe.aCheck the following and deal with if necessary:
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
aStart the vehicle.
aCheck that there are no leaks and deal with them if
necessary.
Note:
If replacing the rubber mounting bush, spray the
inside of the rubber mounting bush with aerosol
spray BRAKE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Con-
sumables - Products) to facilitate fitting.

19B-31
EXHAUST
Silencer: Removal - Refitting
D4F or D7F or K9K
19B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the expansion chamber rubber mounting
bush bolt from the body.
aCut the exhaust pipe (see 19B, Exhaust, Exhaust:
Precautions for the repair, page 19B-8) in the des-
ignated area to be cut (see ) .
aDetach the rubber mounting bush rear silencer.
aRemove the rear silencer.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a
aFit:
-the rear silencer,
-the new After-Sales sleeve (see 19B, Exhaust,
Exhaust: Precautions for the repair, page 19B-
8) .
aTighten the exhaust trunking.
aRefit the expansion chamber rubber mounting bush
bolt on the body.II - FINAL OPERATION
aCheck (and correct if necessary):
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
aStart the vehicle.
aCheck that there are no leaks and deal with them if
necessary.
D4F, and 780
Note:
If replacing the rubber mounting bush, spray the
inside of the rubber mounting bush with brake
cleaner (see Vehicle: Parts and consumables
for the repair) (MR 411, 04B, Consumables -
products) to facilitate fitting.
D4F, and 780

19C-5
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDisconnect:
-the fuel level sensor module connector (2) ,
-the fuel level sensor module pipe union (3) .
aRemove the rear wheels (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aRemove the rear brake drums (see Rear brake
drum: Removal - Refitting) (33A, Rear axle com-
ponents).
aUnclip:
-the handbrake cable from the secondary brake
shoe,
-the handbrake cable from the flange.aRemove:
-the clip (4) between the catalytic converter and the
rear silencer,
-the exhaust pipe rubber mounting bush bolt (5) .
119691
WARNING
To prevent impurities from entering the circuit,
place protective plugs on all fuel circuit compo-
nents exposed to the open air.
D4F or D7F or K9K
D4F or D7F or K9K
119689

19C-6
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRemove:
-the heat shield clips (6) under the tank,
-the heat shield under the tank.aRelease the parking brake lever.
aUnclip the parking brake cables from the callipers at
(7) . D4F or D7F or K9K
119435
K4M
132468

19C-8
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRemove the bolts (12) from the rear brake hose
mounting.
aDetach the brake pipes from the body (13) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the fuel vapour absorber (see 14A, Anti-
pollution, Fuel vapour absorber: Removal - Refit-
ting, page 14A-4) .
aDisconnect the anti-splashback pipe (14) .
aRemove the clip (15) from the filling pipe.
aDisconnect the filling pipe.
119686
119688
D4F or D7F or K4M
121722
WARNING
To prevent impur ities from entering the circuit,
plugs must be fitted to the openings of all the fuel
circuit components exposed to the open air.