2009 RENAULT TWINGO RS torque

14A-20
ANTIPOLLUTION
Exhaust gas recirculation rigid pipe: Removal - Refitting
K9K
14A
aRemove:
-the clip (4) of the exhaust gas recirculation rigid
pipe,
-the bolts (5) from the EGR rigid pipe,
-the EGR rigid pipe.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Exhaust gas recir-
culation rigid pipe
aparts always to be replaced: exhaust gas recir-
culation pipe bolt
aparts always to be replaced: Exhaust gas recir-
culation pipe seal
aparts always to be replaced: exhaust gas cooler
sealaparts always to be replaced: Exhaust gas recir-
culation pipe clip
aUsing an ABRASIVE PAD (see Vehicle: Parts and
consumables for the repair) (04B, Consumables -
Products), clean the bearing face of the exhaust gas
recirculation rigid pipe on the cylinder head.
aUse SURFACE CLEANER and CLEAN CLOTHS to
degrease the bearing face of the exhaust gas recir-
culation rigid pipe on the cylinder head (see Vehi-
cle: Parts and consumables for the repair) (04B,
Consumables - Products).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the rigid exhaust gas recirculation pipe.
aCheck that the rigid exhaust gas recirculation pipe is
not constrained.
aTighten to torque:
-the bolts of the exhaust gas recirculation rigid
pipe on the exhaust manifold (36 N.m),
-the bolts of the exhaust gas recirculation rigid
pipe on the exhaust gas cooler (12 N.m),
-the bolts of the exhaust gas recirculation rigid
pipe bracket (25 N.m). K9K, and 740
114531
K9K, and 718
K9K, and 740
K9K, and 718

14A-21
ANTIPOLLUTION
Exhaust gas recirculation rigid pipe: Removal - Refitting
K9K
14A
aRefit the exhaust gas recirculation rigid pipe with a
new clip.
aFit the rigid exhaust gas recirculation pipe bolts,
without tightening them.
aAdjust the rigid exhaust gas recirculation pipe in re-
lation to the exhaust gas recirculation assembly.
aTorque tighten the rigid exhaust gas recirculation
pipe clip (5 N.m).
aCheck that the rigid exhaust gas recirculation pipe is
not constrained.
aTorque tighten the bolts of the exhaust gas recir-
culation rigid pipe on the exhaust manifold (36
N.m).
III - FINAL OPERATION
aRefit:
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the engine cover.
aConnect the battery (see ) (80A, Battery). K9K, and 740

16A-1
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
16A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection).
aUndo the lower bolt on the sub-frame tie-rod.
aRemove the upper bolt from the sub-frame tie-rod.
aRemove the sub-frame tie-rod.
aRemove the accessories belt (see 11A, Top and
front of engine, Accessories belt: Removal - Re-
fitting, page 11A-3) . Tightening torquesm
alter nator bolts25 Nm
sub-frame tie-rod lower
bolt62 Nm
sub-frame tie-rod upper
bolt21 Nm

16A-3
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
16A
aPress in the rings (6) using pliers or a vice to make
the fitting operation easier.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the alternator,
-the alternator bolts.
aTorque tighten the alternator bolts (25 Nm).
aRefit:
-the power lead on the alternator,
-the power lead nut on the alternator.
aConnect the alternator excitation lead connector.
III - FINAL OPERATION
aConnect the fuel pipe to the injector rail.
aRefit:
-the dipstick,
-the filler neck,
-the filler neck bolt.
aAlways replace the accessories belt.aRefit the new accessories belt (see 11A, Top and
front of engine, Accessories belt: Removal - Re-
fitting, page 11A-3) .
aFit the sub-frame tie-rod.
aRefit the upper bolt on the sub-frame tie-rod.
aTorque tighten:
-the sub-frame tie-rod lower bolt (62 Nm),
-the sub-frame tie-rod upper bolt (21 Nm).
aRefit:
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres).
aConnect the battery (see ) (MR 411, 80A, Battery).
18987
D4F, and 780

16A-4
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and AIR CONDITIONING
16A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) .
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .
aRemove the inlet distributor (see 12A, Fuel mixture,
Inlet distributor: Removal - Refitting, page 12A-
29) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the alternator connector.
aRemove the alternator positive terminal nut.
aRemove:
-the alternator bolts,
-the alternator. Tightening torquesm
alter nator bolts25 N.m
D4F
120519

16A-5
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and AIR CONDITIONING
16A
REFITTING
I - REFITTING PREPARATION OPERATION
aPush in the alternator rings using pliers or a vice to
facilitate fitting the alternator.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the alternator,
-the alternator bolts.
aTorque tighten the alternator bolts (25 N.m).
aRefit the alternator positive terminal nut.
aConnect the alternator connector.
III - FINAL OPERATION
aRefit the inlet distributor (see 12A, Fuel mixture, In-
let distributor: Removal - Refitting, page 12A-29)
.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .aRefit:
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
18987
D4F

16A-7
STARTING - CHARGING
Alternator: Removal - Refitting
K4M
16A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) .II - REMOVAL OPERATION
aRemove:
-the alternator strut bolts (1) ,
-the alternator strut.
aRemove the nut (2) on the alternator positive termi-
nal.
aDisconnect the alternator connector (3) . Tightening torquesm
alter nator bolts25 N.m
nut for the positive ter-
minal of the alternator21 N.m
alter nator strut bolts25 N.m
WARNING
Do not r un the engine without the accessories belt
to avoid damaging the crankshaft accessories pul-
ley.
IMPORTANT
Wear cut-resistant gloves during the operation.
132363
132365

16A-8
STARTING - CHARGING
Alternator: Removal - Refitting
K4M
16A
aLoosen the alternator lower bolt (4) .
aRemove the alternator upper bolt (5) .
aMove the alternator away from the multifunction sup-
port using a screwdriver.
aRemove the alternator.
REFITTING
I - REFITTING PREPARATION OPERATION
aCompress the alternator rings (6) using pliers or a
vice to facilitate fitting.
II - REFITTING OPERATION
aRefit the alternator.
aTorque tighten the alternator bolts (25 N.m).
aConnect the alternator connector.
aTorque tighten the nut for the positive terminal of
the alternator (21 N.m).
132362
18987