2009 RENAULT TWINGO RS engine

11A-37
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aCheck that the tensioning roller does not come into
contact with the cylinder head.
aIf the tensioning roller is in contact with the cylinder
head:
-set the engine to Top Dead Centre,
-remove the tensioning roller and the timing belt,
-insert the tensioning roller pin,
-repeat the timing belt refitting method from the be-
ginning, step by step.
III - FINAL OPERATION
aRefit:
-the lower timing cover,
-the lower timing cover bolt,
-the timing intermediate housing,
-the intermediate timing cover bolts,
-the upper timing cover,
-the upper timing cover.
aTorque tighten:
-the lower timing cover bolt (10 N.m),
-the intermediate timing cover bolts (10 N.m),
-the upper timing cover bolts (37 N.m)aFit the oil pressure sensor connector.
aClip the oil pressure sensor wiring on the upper tim-
ing cover.
aConnect the oil pressure sensor connector.
aFit the flexible heat shield on the oil pressure sensor
connector.
aClip the fuel pipe on to the upper timing cover.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .
aRemove the tool (Mot. 1379).
aRefit:
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
109765
D4F, and 780 or 782

11A-38
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) . Special tooling required
Mot. 1672Low er engine support.
Mot. 1489TDC locating pin.
Mot. 1430Set of 5 crankshaft and cam-
shaft pulley timing pins.
Tightening torquesm
tensioning roller bolt27 N.m
camshaft pulley wheel
bolts14 N.m
TDC setting pin plug25 N.m
cylinder head sus-
pended mounting bolts25 Nm
IMPORTANT
Wear protective gloves during the operation.
WARNING
The belt must be replaced with a new one if it has
been removed.
WARNING
When replacing the belt, always replace the tension
wheels and idler pulleys.
WARNING
Do not r un the engine without the accessories belt
to avoid damaging the crankshaft accessories pul-
ley.

11A-39
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRefit the old crankshaft accessories pulley bolt (1)
fitted with a spacer (2) (which does not cover the tim-
ing sprocket mark).
aUnclip the upper timing cover at (3) .
aRemove the upper timing cover (4) .
aRaise the engine using the lower tool (Mot. 1672).
aUnclip the lower timing cover at (5) .
aLower the engine using the lower tool (Mot. 1672).
aRemove:
-the plastic clip (6) from the lower timing cover,
107272
K9K, and 740
19654
19654-1

11A-40
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
-the lower timing cover (7) .

11A-41
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aUnclip the upper timing cover at (8) and (9)
aRemove:
-the plastic clip (10) from the upper timing cover,
-the upper timing cover.
aUnclip the lower timing cover at (11) and (12) .
aRemove the lower timing cover.
aRaise the engine using the lower tool (Mot. 1672). K9K, and 718
141221
136654
136660
136662

11A-42
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRemove the bolts (13) from the suspended mount-
ing on the cylinder head.
aTwist the timing belt slightly (to facilitate removing
the suspended mounting from the cylinder head).
aRemove the suspended mounting from the cylinder
head.aRemove the plug (14) from the TDC setting pin.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTurn the crankshaft to position the camshaft pulley
hole (15) almost opposite the cylinder head hole (16)
.
136658
11299819650
107270

11A-43
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aFit the tool (Mot. 1489) (17) on the cylinder block.
aTurn the crankshaft clockwise (timing end) smoothly
until the crankshaft is pressed against the TDC set-
ting pin.aInsert the (Mot. 1430) (18) in the camshaft pulley
and cylinder head holes.
aLoosen the timing tensioning roller bolt (19) to relax
the timing belt.
aRemove:
-the timing belt,
-the timing tensioning roller bolt,
-the timing tensioning roller.
19650-1
14489109049
109046

11A-44
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Timing belt
aparts always to be replaced: Timing belt tension-
ing rollerII - REFITTING OPERATION FOR PART
CONCERNED
aRefit a new timing tensioning roller.
aCheck that:
-the lug (20) of the tensioning roller is in place in the
groove (21) of the cylinder head,
-the high pressure pump mark (22) is one tooth to
the right from the vertical axis (23) ,
-the crankshaft is resting on the tool (Mot. 1489)
(the cotter (24) of the crankshaft timing sprocket
upwards).
109042
109043