2009 RENAULT TWINGO RS brake sensor

12A-41
FUEL MIXTURE
Inlet distributor: Removal - Refitting
K4M
12A
aDisconnect:
-the throttle valve connector (4) ,
-the brake servo non-return valve at the inlet distrib-
utor.
aDisconnect the air inlet temperature sensor connec-
tor (5) .aDisconnect:
-all coil connectors (6) ,
-the inlet air pressure sensor connector (7) ,
-the camshaft dephaser solenoid valve connector
(8) .
aUnpick the wiring (9) .
aMove aside the wiring.
aDisconnect the petrol vapour recirculation pipe (10) .
132383
132369132370
131766

12A-43
FUEL MIXTURE
Inlet distributor: Removal - Refitting
K4M
12A
aFit new seals to the inlet distributor.
When replacing the inlet distributor
aparts always to be replaced: Throttle valve seal.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the throttle valve joint face if it is to be re-used,
-the inlet distributor seal housing.
aRefit:
-a new seal on the inlet distributor,
-the throttle valve.
aIn order, torque tighten the throttle valve bolts (10
N.m).
aRefit:
-the oil vapour rebreathing pipe,
-the heat shield,
-the air inlet pressure sensor,-the air inlet temperature sensor.
II - REFITTING OPERATION
aRefit:
-a new seal between the injector holder shim and
the inlet distributor,
-the inlet distributor.
aTighten to torque and in order the inlet distributor
bolts (12 N.m).
III - FINAL OPERATION
aConnect the petrol vapour recirculation pipe.
aPosition the wiring.
aClip on the wiring.
aConnect:
-the camshaft dephaser solenoid valve connector,
-the air inlet pressure sensor connector,
-the connector of each coil,
-the air inlet temperature sensor connector,
-the brake servo non-return valve,
-the throttle valve connector.
aRefit the air outlet pipe onto the air filter unit.
aConnect:
-the air outlet pipe of the air filter unit,
-the oil vapour rebreathing pipe on the air filter unit
air outlet pipe. WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).
WARNING
Do not scrape the joint faces of the aluminium,
any damage caused to the joint face will result in
a risk of leaks.
132383
132371

19C-5
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDisconnect:
-the fuel level sensor module connector (2) ,
-the fuel level sensor module pipe union (3) .
aRemove the rear wheels (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aRemove the rear brake drums (see Rear brake
drum: Removal - Refitting) (33A, Rear axle com-
ponents).
aUnclip:
-the handbrake cable from the secondary brake
shoe,
-the handbrake cable from the flange.aRemove:
-the clip (4) between the catalytic converter and the
rear silencer,
-the exhaust pipe rubber mounting bush bolt (5) .
119691
WARNING
To prevent impurities from entering the circuit,
place protective plugs on all fuel circuit compo-
nents exposed to the open air.
D4F or D7F or K9K
D4F or D7F or K9K
119689

19C-9
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDetach the brake cables (16) on the tank.
aFit a component support under the fuel tank.
aRemove:
-the tank bolts (17) ,
-the tank.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the tank.
aTorque tighten the tank bolts (21 N.m).
aAttach the brake cables to the tank.
aConnect the filler pipe.
aRefit the filler pipe clip on the neck.
aConnect the anti-splashback pipe.aRefit the fuel vapour absorber (see 14A, Antipollu-
tion, Fuel vapour absorber: Removal - Refitting,
page 14A-4) .
II - FINAL OPERATION.
aConnect the brake pipes to the body.
aRefit the rear brake hose mounting bolts.
aClip the protective housing of the ABS connectors
onto the tank.
aConnect the ABS sensor connectors.
aClose the anti-lock braking system sensor connector
protective housing.
aRefit:
-the heat shield under the tank.
-the heat shield clips under the tank,
-the exhaust system rubber mounting bush bolt,
-the clip between the catalytic converter and the ex-
pansion chamber,
aClip the calliper parking brake cables onto the tank
and the callipers.
119652
119685
D4F or D7F or K4M
K4M

19C-10
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRefit:
-the heat shield under the tank,
-the heat shield clips under the tank
aTighten to torque:
-the exhaust pipe rubber mounting bush bolt (21
N.m),
-the clip between the catalytic converter and the
rear silencer (21 N.m).
aClip:
-the handbrake cable onto the flange,
-the handbrake cable onto the secondary brake
shoe.
aRefit the rear brake drums (see Rear brake drum:
Removal - Refitting) (33A,Rear axle components).
aRefit the rear wheels (see Wheel: Removal - Refit-
ting) (35A, Wheels and tyres).
aConnect:
-the fuel level sensor module pipe union,
-the fuel level sensor module connector.
aRefit the access flap for the fuel level sensor mod-
ule.
aRefit the rear bench seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery). D4F or D7F or K9K