2009 RENAULT TWINGO RS check engine

87B-118
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET087
ONE-TOUCH WINDOW CONTROL/SUNROOF AUTHORISATION.
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC070 One-touch windows/SR* is With. Otherwise, perform CF173
One-touch windows/SR.
Authorisation by the UCH of the one-touch window winder and/or sunroof motor
function is present under the following conditions:
–+ ACCESSORIES FEED,
–+ AFTER IGNITION FEED,
–when the engine is running.
SPECIFICATIONSPRESENT
ABSENT
Check the condition and connection of the PE2 24-track UCH connector, (component code 645) (tabs bent,
broken, oxidised).
Check the condition and connection of the driver's electric window motor 6-track connector (component 203)
(tabs bent, broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If there is an electric sunroof, check that fuse F26 (20 A) is sound and correctly fitted in the passenger
compartment fuse and relay box (component code 1016).
Check the condition and connection of the connectors for component 1512.
With an electric sunroof, check the condition and connection of 4-track connector 339 in the A-pillar and the
sunroof computer 12-track connector (tabs bent, broken, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET087

87B -128
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET114
ET115
WIPER REQUEST BY RAIN SENSOR
LIGHT ACTIVATION REQUEST BY LIGHT SENSOR
NOTESThere must be no present or stored faults.
Make sure that the vehicle is fitted with the rain and light sensor.
The status should change to LOW SPEED or HIGH SPEED if there is water on the
windscreen where the sensor is positioned.
The status should change to PRESENT when the light intensity requires the lights to
be switched on with the engine running.
Make sure that the other positions of the wiper control are working properly
Check the following configurations:
–Check that LC008 Daytime running lights is "With". Otherwise run CF014
Daytime running lights.
–Check that LC044 Rain/light sensor displays "Present". If not, run CF035 Rain/
light sensor.
–Check that LC095 Automatic headlight function displays "With". If not, run
CF193 Automatic headlight function.
–Check that LC096 Automatic wiper function displays With. If not, run CF194
Automatic wiper function.
SPECIFICATIONSET114: ABSENT/LOW SPEED/HIGH SPEED
ET115: PRESENT/ABSENT
Conditions:
Check that the switch stalk (component code 209) is in the intermittent position so that automatic operation can
be activated.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, perform the following cycle twice to activate the automatic headlight
function: Switch stalk (component code 209) OFF → Σωιτχη σταλκ (χοµπονεντ χοδε 209) to side lights ON
position.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET114 / UCH_V44_ET115

87B -130
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET142
ENGINE OPERATING PHASE
NOTESThere must be no present or stored faults.
SPECIFICATIONSSTOPPED
STARTING
RUNNING
STALLED
Run a multiplex network test (see 88B, Multiplexing).
Carry out fault finding on the injection system (see 13B, Diesel injection or 17B, Petrol injection).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET142

87B -136
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET239
IGNITION SWITCH POSITION
NOTESThere must be no present or stored faults.
SPECIFICATIONS+ APC
+ START
+ ACCESSORIES FEED
Check the correct position and condition of fuses F2 (60A) in the engine fuse and relay box (component code
597) and F8 (15A) in the passenger compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the starter switch connector (component code 104) (tabs bent, broken,
oxidised).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for +12 V on connection AP29 of component 232.
Check the insulation, continuity and the absence of interference resistance on the connections between the
UCH (component code 645) and the ignition switch (component 104):
●Connection code A between components 104 and 1016.
●Connection code BP12 between components 104 and 597.
●Connection code AP43 between components 1016 and 645.
●Connection code D between components 104 and 232.
●Connection code 1B between components 232 and 645.
●Connection code AP29 between components 1016 and 232.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are in order, replace the ignition switch (component code 104).
(See MR 411 Mechanical 82A, Immobiliser, Ignition switch: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET239

87B -138
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
*Powerlatch: Time required for injection computer supply after + 12 V after ignition feed cut-off to the ignition switch. ET250
INJECTION
NOTESThere must be no present or stored faults.
Switch on the + after ignition feed for 20 seconds, switch off the ignition, wait until the
end of Powerlatch* (20 minutes maximum), then switch on the ignition again.
Check that the immobiliser warning light remains lit.
SPECIFICATIONSNOT PROTECTED
PROTECTED
After the setpoint has been obtained, if the status remains PROTECTED, first check that statuses ET046 Engine
immobiliser, ET181 Key allocated to vehicle and ET229 Injection immobiliser code are operating correctly.
Carry out a multiplex network test (see 88B, Multiplexing).
Carry out fault finding on the injection system (see 13B, Diesel injection or 17B, Petrol injection).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET250

87B -141
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
Special feature: Depending on the vehicle equipment, an additional fuse and diode are present on the
wiring: ET463
CONTINUED 2
Check the insulation, continuity and the absence of interference resistance of the following connections:
Central door locking/warning switch check (component code 1391):
●Connection code 20AW between components 645 and 1391.
●Connection code 20M between components 645 and 1391.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the central door locking/warning switch (component code 1391).
(See MR 411 Mechanical 84A, Control - Signals, Hazard warning lights and central door locking:
Removal - Refitting).
With the engine running, check that the door
open warning (buzzer) is active when the driver
door is open and the lights are on.
Is the warning active?
NO
Check the continuity of connection H24 between
components 140 and 1016 and between
components 119 and 1016.
Is the continuity correct?
NO
C
YESB

87B -147
MR-413-X44-87B000$720.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of parameters
UCH
Vdiag No.: 44
87B
PR073
ALTERNATOR CHARGE SIGNAL
NOTESNo faults should be present or stored.
Note:
In the event of a malfunction, the value will by 99.6% (engine running).
Depending on the battery charge status, the operating phase and the battery temperature, the UCH determines
what the voltage across the battery terminals should be.
When the battery charge drops, and PR076 Battery voltage after rest decreases, the UCH can temporarily
increase the PR075 Alternator setpoint voltage by 1 V and for a period of 15 minutes after switching on + after
ignition feed.
Before and during starting, PR075 Alternator setpoint voltage is fixed at 10.7 V.
A maximum of 30 seconds after the engine has started, the UCH sets PR075 Alternator setpoint voltage to the
optimum value calculated.
The injection computer can also control the alternator (component code 103) regulation voltage.
The injection computer sends the maximum authorised power delivered by the engine, to the UCH via the
multiplex network.
If the power available by the engine is less than the power consumed by the alternator (component code 103),
the UCH reduces PR075 Alternator setpoint voltage.
0 % < PR073 < 100 %
In the event of a fault, carry out a complete check on the battery and the charging circuit (see Technical Note
16A, Starting-Charging).
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
UCH_V44_PR073

87B -148
MR-413-X44-87B000$720.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of parameters
UCH
Vdiag No.: 44
87B
PR074
BATTERY SETPOINT VOLTAGE
NOTESNo faults should be present or stored.
Depending on the battery charge status, the operating phase and the battery temperature, the UCH determines
what the voltage across the battery terminals should be.
When the battery charge drops, and PR076 Battery voltage after rest decreases, the UCH can temporarily
increase the PR075 Alternator setpoint voltage by 1 V and for a period of 15 minutes after switching on + after
ignition feed.
Before and during starting, PR075 Alternator setpoint voltage is fixed at 10.7 V.
A maximum of 30 seconds after the engine has started, the UCH sets PR075 Alternator setpoint voltage to the
optimum value calculated.
The injection computer can also control the alternator (component code 103) regulation voltage.
The injection computer sends the maximum authorised power delivered by the engine, to the UCH via the
multiplex network.
If the power available by the engine is less than the power consumed by the alternator (component code 103),
the UCH reduces PR075 Alternator setpoint voltage.
In the event of a fault, perform a complete check on the battery and charging circuit (see 80A, Battery).
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
UCH_V44_PR074