2009 RENAULT TWINGO RS wheel

82A-3
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSet the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and pre-
tensioners, Fault finding - Replacement of com-
ponents).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .
aRemove:
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6)
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aMake a saw mark on the shear bolt.
aRemove the bolt (1) .
aLoosen the connector at (2) .
aDisconnect the starter switch connector. Equipment required
Diagnostic tool
ENGINE REV COUNTER
119489
119490

82A-4
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
aPosition the ignition key between the first and se-
cond position (+ accessories and + after ignition
feed) (3) .
aPress the retaining lug (4) .
aRemove the ignition switch.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the ignition switch bolt,
-the steering wheel bolt.
II - REFITTING OPERATION FOR PART
CONCERNED
aaPosition the ignition key between the first and se-
cond position (+Accessories and +APC) (5) .
aPress the retaining lug (6) .
aFit the ignition switch.
aTighten the shear bolt (7) until the bolt head shears
off.
aConnect the starter switch connector.
aLock the starter switch connector.
108441
Note:
To protect against tampering, always secure the
ignition switch with a shear bolt.
Be sure to recover the sheared-off part of the
bolt after it has been tightened.
108441
119491

82A-5
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
III - FINAL OPERATION.
aRefit:
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) ,
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6) .
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
pretensioners, Fault finding - Replacement of
components). ENGINE REV COUNTER

82B-1
HORN
Audible warning: Removal - Refitting
82B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the front right-hand wheel arch liner ( (see
Front wheel arch liner: Removal - Refitting) ).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the horn connector (1) .
aRemove:
-the horn bolt (2) ,
-the horn.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the horn,
-the horn bolt.
aConnect the horn connector.
II - FINAL OPERATION.
aRefit the front right-hand wheel arch liner ( (see
Front wheel arch liner: Removal - Refitting) ).
119381

83D-2
CRUISE CONTROL
Switch: Removal - Refitting
CRUISE CONTROL
83D
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the storage compartment (1) under the
steering wheel.
aUnclip the trim under the steering wheel (2) .
aDisconnect the various connectors from the plate.
aRemove the trim under the steering wheel.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the switch (4) from the trim under the steering
wheel by pressing the clips (3) .
REMOVAL
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the switch onto the trim under the steering
wheel.
II - FINAL OPERATION.
aConnect the various connectors.
aRefit the trim under the steering wheel.
aRefit the storage compartment under the steering
wheel.
119506
120279
120277

83D-3
CRUISE CONTROL
Steering wheel switch: Removal - Refitting
CRUISE CONTROL
83D
The steering column switches cannot be separated
from the steering wheel.
In the event of any faults, replace the steering wheel
(see Steering wheel: Removal - Refitting) (MR 411,
36B, Power-assisted steering).

84A-2
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Set the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .aRemove the lower cover bolts (1) .
aUnclip the upper cover at (2) .
aRemove the upper cover (3) . Equipment required
Diagnostic tool
WARNING
To prevent damaging the rotar y switch, do not turn
the mobile section of the rotary switch.
WARNING
Incorrect wheel alignment could ruin the rotary
switch.
ENGINE REV COUNTER
127437
127438

84A-3
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
aRemove the lower cover (4) .
aRemove:
-the driver's side front airbag (see 88C, Air bag and
Pretensioners, Driver's frontal airbag: Removal
- Refitting, page 88C-6) ,
-the steering wheel (see Steering wheel: Removal
- Refitting) (36B, Power-assisted steering),II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLock the driver's front airbag (5) connector in the
housing of the radio satellite connector to immobilise
the rotary switch throughout the removal operation.
127439
127766