2009 RENAULT TWINGO RS diagram

86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < X < 15 V).
Note:
Apply this fault finding method if the fault reappears as present after having been
cleared
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
•for New Twingo: F48 (15A),
•for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R108_VA4_DF039

86A-41
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF040
DF043
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF: No communication with the CD changer
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct if necessary, using SC002 Computer configuration.
Look for any signs of damage to the wiring harness, check the condition and connection of the connectors and
connections of components 261 and the CD changer.
If the connectors or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector or the wiring, otherwise replace
the wiring.
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the checks are correct, replace the CD changer.
If the fault persists, contact your Techline.
R108_VA4_DF040/R108_VA4_DF043

86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064

86A-60
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
86A
R01-08
Vdiag No.: A4
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated and
radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R108_VA4_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-71
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 2 The radio beeps every 2 seconds
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
The radio beeps every 2 seconds.
The radio is in factory mode.
Wait for 2 minutes for the radio to request
the code.
Does the radio request the code?
Enter the radio security code (see Anti-theft
code).
Is the code correct?If the radio displays a countdown in seconds,
then the code that was entered is incorrect.
Wait for the time indicated on the display for the
radio to request the code, then enter the correct
code.
The problem disappears.Was the code accepted?
Contact the Techline.
NO
YES
NO
YES
YES
NO
R108_VA4_ALP2

86A-74
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 5 The radio control satellite does not operate or operates poorly
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Has dialogue been established with the
multimedia interface unit (Display or
multimedia connection unit)?Consult ALP 1 No dialogue with the
computer for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding charts).
Check the condition of the radio control satellite
(see 86D, Multimedia interface unit,
Conformity check).
Are the checks correct?Contact the Techline.
NO
YES
YES
NO
A
R108_VA4_ALP5

86A-77
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 6 Radio reception fault.
NOTESFor the aerial, use component code 1874 for a vehicle equipped with a navigation
system, and 1208 for a vehicle without this option.
See Clio III or New Twingo wiring diagrams.
See Clio III or New Twingo wiring diagrams.
Check the presence and condition of the radio
aerial.Replace the radio aerial, component code
1208 or 1874 (see MR 392, 86A, Radio, Radio
aerial: Removal - Refitting) for New Twingo
or (see MR 411, 86A, Radio, Radio aerial:
Removal - Refitting) for Clio III. Is the radio aerial correct?
Check the condition of the connections of the
radio aerial coaxial cable at the radio aerial,
component code 1208 or 1874 and of the radio,
component code 261.
Are the connections correct?If the connectors are faulty and if there is a
repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair) repair the
connector(s); otherwise, replace the wiring.
NO
YES
NO
YES
A
R108_VA4_ALP6

86A-80
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 8Backlighting does not change when the vehicle lights are
switched on
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
NOTE: Switch on the side lights and position the lighting rheostat wheel in the centre
position.
The display, component code 653, is only available when the vehicle does not have
the navigation function.
The multimedia connection unit, component code 1714, is only available when the
vehicle has the navigation function.
Check the backlighting of the following components:
radio, display and instrument panel.
Are all of the components backlit?
Attempt to backlight these components
once again, and if no conclusion can be
made, contact the Techline.
Does the instrument panel light up?Perform fault finding on the instrument
panel (see 83A, Instrument panel).
YES
NO
NO
YES
A
R108_VA4_ALP8