2009 RENAULT TWINGO RS ABS

80D-30
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 5
CONTINUED 2
Check between the horn and lights switch (component 209) and the passenger compartment fuse and
relay box (component 1016):
Check the insulation, continuity and the absence of interference resistance on the following connection:
●Connection code L between components 209 and 1016.
●Connection code BP59 between components 209 and 1016.
●Connection code MAN or MAM between components 209 and earth MAN or earth MAM (depending on the
driving layout, right- or left hand drive).
Check between the engine relay/fuse box (component 597) and the passenger compartment fuse and relay
box (component 1016):
●Connection code BP11 between components 597 and 1016.
●Connection code BP13 between components 597 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies, earth and connections are correct, replace the horn and lights switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

80D-31
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
If the vehicle lighting is controlled by the UCH (with rain/light sensor):
If the vehicle lighting is not controlled by the UCH (no rain/light sensor):
ALP 6 No dipped headlights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check, as a priority, the operation of status ET081 Lighting stalk position and
command AC054 Dipped headlights in the UCH. If there is a malfunction on status
ET081 "Lighting stalk position" and command AC054 "Dipped headlights", refer
to the interpretation of status ET081 "Lighting stalk position" and of command
AC054 "Dipped headlights".
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the condition of the bulbs and the cleanliness
of their contacts.
Are the bulbs and their contacts in good
condition?
YES
Replace the light concerned.
Check that fuses F13 (30 A), F34 (15 A) and F35 (15 A) are sound and correctly fitted in the passenger
compartment fuse and relay box.
Replace the fuse if necessary.
Check the condition and connection of the light connector concerned (bent, oxidised, broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
NOClean the contacts and replace any bulbs in
poor condition.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP6

80D-32
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 6
CONTINUED 1
Check the condition and connection of the horn and lights switch connector (tabs broken, bent, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a dipped headlights request) on connection CPD of component 226 and
connection CPG on the connection of component 227. Check for an earth on connection MAR of component 226
and on connection MAS on component 227. Check the supply to connection LPD on component 172 and the
supply to connection LPG on component 173.
Dipped headlights check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Right-hand front dipped headlight:
●Connection code CPD between components 226 and 1016.
●Connection code MAR between components 226 and earth MAR.
Left-hand front dipped headlight:
●Connection code CPG between components 227 and 1016.
●Connection code MAS between components 227 and earth MAS.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BP59 and BP11 of component 209. Check for earth on the connection. Check
for earth on connection MAN (for right-hand drive vehicles) or MAM (for left-hand drive vehicles) of
component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

80D-33
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 6
CONTINUED 2
Horn and lights switch check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code CS0 between components 209 and 1016.
●Connection code BP59 between components 209 and 1016.
●Connection code BP11 between components 209 and 1016.
●Connection code MAN or MAM between components 209 and earth MAN or earth MAM (depending on the
driving layout, right- or left hand drive).
Check between the engine relay/fuse box (component 597) and the Passenger compartment fuse and relay
box (component 1016):
●Connection code BP11 between components 597 and 1016.
●Connection code BP13 between components 597 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies, earth and connections are correct, replace the horn and lights switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

80D-34
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
If the vehicle lighting is controlled by the UCH (with rain/light sensor):
If the vehicle lighting is not controlled by the UCH (no rain/light sensor):
ALP 7 No main beam headlights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check, as a priority, the operation of status ET081 Lighting stalk position and
command AC062 Main beam headlights in the UCH. If there is a malfunction on
status ET081 "Lighting stalk position" and command AC062 "Main beam
headlights", refer to the interpretation of status ET081 "Lighting stalk position"
and of command AC062 "Main beam headlights".
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the condition of the bulbs and the cleanliness
of their contacts.
Are the bulbs and their contacts in good
condition?
YES
Replace the light concerned.
Check that fuses F13 (30 A), F32 (10 A) and F33 (10 A) are sound and correctly fitted in the passenger
compartment fuse and relay box.
Replace the fuse if necessary.
Check the condition and connection of the light connector concerned (bent, oxidised, broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the horn and lights switch connector (tabs broken, bent, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
NOClean the contacts and replace any bulbs in
poor condition.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP7

80D-35
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 7
CONTINUED
Check for + 12 V (when there is a main beam headlights request) on connection RPD of component 226 and
connection RPG on component 227. Check for an earth on connection MAR of component 226 and on
connection MAS of component 227.
Main beam headlights check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
Front right-hand main beam headlight:
●Connection code RPD between components 226 and 1016.
●Connection code MAR between component 226 and earth MAR.
Front left-hand main beam headlight:
●Connection code RPG between components 227 and 1016.
●Connection code MAS between component 227 and earth MAS.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BP59 and BP11 of component 209. Check for earth on connection MAN (for
right-hand drive vehicles) or MAM (for left-hand drive vehicles) of component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check between the horn and lights switch and the passenger compartment fuse and relay box:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code R between components 209 and 1016.
●Connection code BP59 between components 209 and 1016.
●Connection code BP11 between components 209 and 1016.
●Connection code MAN or MAM between components 209 and earth MAN or earth MAM (depending on the
driving layout, right- or left hand drive).
Check between the engine relay/fuse box (component 597) and the Passenger compartment fuse and relay
box (component 1016):
●Connection code BP11 between components 597 and 1016.
●Connection code BP13 between components 597 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies, earth and connections are correct, replace the horn and lights switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

80D-36
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
If the vehicle lighting is not controlled by the UCH (no rain/light sensor):
If the vehicle lighting is controlled by the UCH (with rain/light sensor):
ALP 8 No front fog lights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
If the fog light control on the horn and lights switch is a one-touch control, check that
the front fog lights are "WITH" by reading configuration LC015 "Front fog lights".
Otherwise use command CF021 "Front fog lights".
Check the operation of status ET111 Front fog lights request and command AC008
Front fog light in the UCH. If there is a malfunction on status ET111 "Front fog
lights request" and command AC008 "Front fog lights", refer to the interpretation
of status ET111 "Front fog lights request" and command AC008 "Front fog
lights".
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the condition of the bulbs and the cleanliness
of their contacts.
Are the bulbs and their contacts in good
condition?
YES
Replace the light concerned.
Check that fuse F13 (10 A) is sound and fitted in the passenger compartment fuse and relay box.
Replace the fuse if necessary.
Check the condition and connection of the light connector concerned (bent, oxidised, broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
NOClean the contacts and replace any bulbs in
poor condition.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP8

80D-37
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 8
CONTINUED 1
Check the condition and connection of the horn and lights switch connector (tabs broken, bent, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a front fog lights request) on connection 8B of components 176 and 177. Check
for an earth on connection MAR of component 176 and connection MAS on component 177.
Front fog lights check:
Check the insulation, continuity and the absence of interference resistance on the following connection:
Right-hand front fog light:
●Connection code 8B between components 231 and 176.
Left-hand front fog light:
●Connection code 8B between components 231 and 177.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V (when there is a front fog lights request) on connection 8A of component 231.
Check for + 12 V on connection BP16 of component 231. Check the earth on connection MAM of
component 231.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.