2009 RENAULT TWINGO RS ignition

83A-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 2
NOTESVehicle under + after ignition feed.
VEHICLE CHECKUse the Universal bornier to check the following connections on the vehicle diagnostic
socket, component code 225:
BP19 "+ protected battery feed" of component 225.
•MAN (if left-hand drive) of component 225.
•MAM (if right-hand drive) of component 225.
•NAM, the earth of component 225.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Check the earth of connection MAN of the instrument panel, component code 247.
If the earth MAN is poor, check the insulation to + 12 V and check the continuity of
the following connection:
•MAN of component 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Check for + 12 V on connection AP43 and connection BP49 of the instrument panel,
component code 247.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If there is no + 12 V, check the insulation to earth and the continuity of the following
connections:
•AP43 between components 247 and 1016,
•BP49 between components 247 and 1016.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.

83A-52
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2 The fuel level indicator does not display full
NOTESThe fuel tank must be filled with the ignition switched off (advise the customer to remove
the key).
Ideally the customer must fill the tank with at least 15 litres.
See Wiring diagram Technical Note, New Twingo.
Ask the customer if the tank is filled up under the
following conditions:
–the customer filled the tank up to the 3
rd cut-out
–the customer has changed filling station
–the customer filled the tank in a flat-level station (not
on a slope).
Did the customer fill the tank while observing all of
these conditions?Ask the customer to return just after
having filled the tank under the conditions
mentioned above.
NO
YES
A
TDB_V04_ALP2/TDB_V08_ALP2

83A-53
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2
CONTINUED 1
With the ignition off, disconnect the fuel sender
connector, component code 833 and then check
the resistance using a multimeter.
The value should be: 38 ΩΩ Ω Ω
.
Is the value measured less than 38 ΩΩ Ω Ω
?Replace the fuel sender, component code
833 (see MR 411, Mechanical, 19C, Fuel
tank, Sender: Removal - Refitting).
If the fault is still present, contact Techline.
Compare the value measured to the value supplied
by the CLIP tool.
Is the value measured and the value provided
by the CLIP tool the same as or approximately
± 5 ΩΩ Ω Ω
?
A
YES
NO
YES
NOC
YES
B

83A-59
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.Replace the instrument panel,
component code 247 (see
MR 411, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
Record the resistance value provided by the CLIP tool.
Compare the value from the CLIP tool with the warning
resistance, which should be 260 ΩΩ Ω Ω
.
Is this value above or equal to 260 ΩΩ Ω Ω
?Contact the Techline.
Rock the vehicle and check whether the resistance changes by
± 5 ΩΩ Ω Ω
.
Is there a change in the resistance value?Contact the Techline.
NO
YES
YES
NO
YES
NO
A
TDB_V04_ALP5/TDB_V08_ALP5

83A-60
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5
CONTINUED 1
With the ignition off, disconnect the fuel sender connector,
component code 833 and then check the resistance using a
multimeter.
Replace the sender, component
code 833 (see MR 411,
Mechanical, 19C, Fuel tank,
Sender: Removal - Refitting). Is the measured value above or equal to 260 ΩΩ Ω Ω
?
Compare the value measured to the value supplied by the CLIP
tool.
Is the value measured and the value provided by the CLIP
tool the same as or approximately ± 5 ΩΩ Ω Ω
?
Contact the Techline.
A
NO
NO
YES
NOB
YES

83A-63
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 6Fault with no warning given by warning light (addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.
Does the fuel warning light illuminate for 3
seconds when + after ignition is switched on?Replace the instrument panel,
component code 247 (see MR 411,
Mechanical, 83A, Instrument panel,
Instrument panel: Removal -
Refitting).
With the ignition off, disconnect the fuel sender
connector, component code 833 and then check the
resistance using a multimeter.
Compare the value measured to the value supplied by
the CLIP tool.
Is the value measured and the value provided by
the CLIP tool the same as or approximately ± 5 ΩΩ Ω Ω
?
Contact the Techline.
NO
YES
NOB
YES
TDB_V04_ALP6/TDB_V08_ALP6