2009 RENAULT TWINGO RS Gearbox mount

31A-48
FRONT AXLE COMPONENTS
Front axle subframe: Removal - Refitting
31A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the speed selection cable guide on the sub-
frame.
aRefit:
-the front driveshaft lower arms (see 31A, Front
axle components, Front driveshaft lower arm:
Removal - Refitting, page 31A-33) ,
-the front anti-roll bar (see 31A, Front axle compo-
nents, Front anti-roll bar: Removal - Refitting,
page 31A-52) ,
-the steering box (see 36A, Steering assembly,
Steering box: Removal - Refitting, page 36A-1) .
aRefit the « subframe - front driveshaft lower arm -
steering box - front anti-roll bar » assembly with the
(Mot. 1390).
aTighten to torque:
-the rear subframe bolts (105 Nm) (20) ,
-the front subframe bolts (62 Nm) (22) ,
-the front end cross member bolts (21 Nm) (21) .aRefit:
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the acoustic tie rods.
aTighten to torque:
-the acoustic tie-rod bolts (21 Nm) (23) ,
-the acoustic tie-rod bolts (90 Nm) (24) .
aRefit the sub-frame tie-rods.
aTighten to torque:
-the subframe tie-rod bolts (21 Nm),
-the subframe tie-rod nuts (62 Nm).
aCheck the position of the gear selection cables in the
guide.
aFit the gearbox control gear lever arm.
aTorque tighten the gear lever arm nut (28 Nm).
aFit the gear lever arm rubber protector. K9K
Note:
Be careful with the guide of the lower or upper
radiator when fitting the subframe. There is a risk
of the radiator guides breaking.
119336
119335
K9K
JB1

33A-37
REAR AXLE COMPONENTS
Complete rear axle system: Removal - Refitting
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRelease the parking brake.
aFit the pedal press on the brake pedal to limit the
amount of brake fluid running out.
aRemove the rear wheels (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Removal
aRemove:
-the heat shield clips (1) ,
-the heat shield.
aUndo the adjusting screw (2) of the parking brake
compensator.
aRemove the parking brake compensator brake ca-
bles. Special tooling required
Mot. 1390Suppor t for removal - refitting
of engine - gearbox assembly
Equipment required
pedal press
safety strap(s)
Tightening torquesm
rear axle bearing bolts62 Nm
brake hose lower unions17 Nm
119435
119436

37A-14
MECHANICAL COMPONENT CONTROLS
Brake servo: Removal - Refitting
JB1 or JH1 or JH3 or JR5, and LEFT-HAND DRIVE
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aRemove the gearbox computer (see Sequential
gearbox converter: Removal - Refitting) (21B,
Sequential gearbox).
aRemove the battery tray (see Battery tray: Remov-
al - Refitting) (80A, Battery).
aRemove the petrol injection computer (see Petrol
injection computer: Removal - Refitting) (17B,
Petrol injection).
aRemove the diesel injection computer (see Diesel
injection computer: Removal - Refitting) (13B,
Diesel injection).
aRemove:
-the injection computer mounting bolts (1) ,
-the engine harness bracket nut (2) ,
-the injection computer mounting,
-the master cylinder (see 37A, Mechanical compo-
nent controls, Master cylinder: Removal - Refit-
ting, page 37A-1) . Tightening torquesm
brake servo nuts25 Nm
JH1
D4F or D7F or K4M
K9K
122323
122322