2009 RENAULT TWINGO RS wheel bolts

36A-13
STEERING ASSEMBLY
Steering column: Removal - Refitting
RIGHT-HAND DRIVE
36A
-the bolt connecting the steering column and the in-
termediate shaft,
-the steering column intermediate shaft.
aRemove:
-the steering column bolts (10) ,
-the steering column with the intermediate shaft,
REFITTING
I - REMOVAL PREPARATION OPERATION
aAlways replace:
-the steering wheel bolt,
-the universal joint cam nut and bolt.II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the intermediate shaft of the steering column,
-the bolt connecting the steering column and the in-
termediate shaft.
aTorque tighten the bolt connecting the steering
column and the intermediate shaft (30 Nm).
aRefit:
-the steering column with the intermediate shaft on
the cross member using the retainer (11) ,
-the bolts on the steering column.
aTorque tighten the steering column bolts (21 Nm).
aConnect the power-assisted steering computer con-
nectors. MANUAL STEERING
119647
POWER ASSISTED STEERING
119859
POWER ASSISTED STEERING

36A-15
STEERING ASSEMBLY
Steering column: Removal - Refitting
RIGHT-HAND DRIVE
36A
-the steering wheel lower cover,
-the steering wheel lower cover bolts,
-the dashboard lower cover.
aRefit the rev counter (see Rev counter: Removal -
Refitting) (MR 411, 83A, Instrument panel).
aRefit:
-the steering wheel (see 36A, Steering assembly,
Steering wheel: Removal - Refitting, page 36A-
23) ,
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
and pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
a
Unlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and pretensioners). ENGINE REV COUNTER
IMPORTANT
To avoid a fault with or even triggering of pyro-
technic components (airbags or pretensioners),
check the airbag computer using the diagnostic
tool.

36A-21
STEERING ASSEMBLY
Steering column adjustment handle: Removal - Refitting36A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see ) (80A, Battery).
aUnclip the dashboard lower trim.
aDisconnect the various connectors.
aPut the handle in the low position (to prevent the mo-
bile part of the column dropping during dismantling).
aRemove:
-the bolts on the steering wheel lower cover,
-the steering wheel lower cover.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the nut (1) of the adjustment handle shaft while
holding the handle during unscrewing,
-the locking mechanism (2) of the adjustment han-
dle,
-the adjustment handle (3) .
119711
Note:
The removal of the steering wheel is not neces-
sary.
127586
Note:
Do not keep the components of the locking
mechanism and scrap all of its constituent parts,
as well as the adjustment handle.

36B-2
POWER ASSISTED STEERING
Power-assisted steering computer: Removal - Refitting
LEFT-HAND DRIVE
36B
aRemove:
-the power-assisted steering computer bolts (4) ,
-the power-assisted steering computer,
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the power-assisted steering computer.
aConnect the power-assisted steering computer con-
nectors.
aFasten the locking clips of the connectors of the
power-assisted steering computer.
II - FINAL OPERATION.
aRefit the steering wheel lower cover.
aConnect the various connectors.
aClip:
-the dashboard lower trim,
-the fuse access flap.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aWhen replacing the electric power-assisted steering
computer, perform the necessary operations using
the Diagnostic tool (see Fault finding - Replace-
ment of components) (36B, Power-assisted steer-
ing).
119882

37A-11
MECHANICAL COMPONENT CONTROLS
Brake servo non-return valve: Removal - Refitting
RIGHT-HAND DRIVE
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front right-hand wheel (see 35A, Wheels and
tyres, Wheel: Removal - Refitting, page 35A-1) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment).
aRemove:
-the bolts (1) from the bulkhead heat-resistant pro-
tector,
-the bulkhead heat-resistant protector (2) .aRemove:
-the upstream oxygen sensor (see Oxygen sen-
sors: Removal - Refitting) (MR 411, 17B, Petrol
injection),
-the bolts (3) from the bulkhead heat-resistant pro-
tectors,
-the nuts (4) from the bulkhead heat-resistant pro-
tectors, D4F or D7F
123866
D4F, and 780
123903
123908

37A-13
MECHANICAL COMPONENT CONTROLS
Brake servo non-return valve: Removal - Refitting
RIGHT-HAND DRIVE
37A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the non-return valve.
aClip on the non-return valve.
aConnect the non-return valve pipe:
-to the brake servo,
-to the intake distributor.
II - FINAL OPERATION.
aRefit:
-the bulkhead heat-resistant protectors,
-the bulkhead heat-resistant protector nuts,
-the bulkhead heat-resistant protector bolts,
-the upstream oxygen sensor (see Oxygen sen-
sors: Removal - Refitting) .
aRefit:
-the bulkhead heat-resistant protector,
-the bulkhead heat-resistant protector bolts.
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection),
-the front right-hand wheel (see 35A, Wheels and
tyres, Wheel: Removal - Refitting, page 35A-1) . D4F, and 780
D4F or D7F

37A-42
MECHANICAL COMPONENT CONTROLS
Brake pedal switch: Removal - Refitting
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the bolts (1) of the steering wheel cover,
-the steering wheel cover (2) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the brake light switch connector (3) .
aTurn the brake light switch (4) a quarter of a turn
anti-clockwise.
aRemove the switch from the pedal assembly. Equipment required
set of feeler gauges
Diagnostic tool
WARNING
The brake pedal position switch must be replaced if
the notched segment is pulled completely out of the
switch.
120279
121350

37A-45
MECHANICAL COMPONENT CONTROLS
Brake pedal switch: Removal - Refitting
37A
III - CHECKING THE ELECTRICAL OPERATION OF
THE PART
aCheck that the brake light switch is operating cor-
rectly:
-depress the brake pedal to switch on the lights,
-release the brake pedal to switch off the lights.
aConnect the Diagnostic tool
aDepress the brake pedal by 10 mm.
aCheck that the first signal of the switch has not
switched (the first signal does not illuminate the
bulbs).
IV - FINAL OPERATION
aRefit:
-the steering wheel cover,
-the bolts on the steering wheel cover.