2009 RENAULT TWINGO RS dashboard

36B-3
POWER ASSISTED STEERING
Power-assisted steering computer: Removal - Refitting
RIGHT-HAND DRIVE
36B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aUnclip the dashboard lower trim
aDisconnect the various connectors.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (1) of the support of the power-as-
sisted steering computer.
aSeparate the "support - computer" assembly (2) .
aUnclip the locking clips of the connectors of the pow-
er-assisted steering computer.
aDisconnect the connectors (3) of the power-assisted
steering computer.
aRemove the "support - computer" assembly. Equipment required
Diagnostic tool
127585
127588
127589

36B-4
POWER ASSISTED STEERING
Power-assisted steering computer: Removal - Refitting
RIGHT-HAND DRIVE
36B
For replacing the computer:
a
aRemove:
-the power-assisted steering computer bolts (4) ,
-the power-assisted steering computer from its sup-
port.
REFITTING
I - REFITTING PREPARATION OPERATION
For replacing the computer:
aRefit the computer on its support.
II - REFITTING OPERATION FOR PART
CONCERNED
aConnect the power-assisted steering computer con-
nectors.
aFasten the locking clips of the connectors of the
power-assisted steering computer.
aRefit the "support - computer" assembly.III - FINAL OPERATION.
aConnect the various connectors.
aClip on the dashboard lower trim.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aWhen replacing the power-assisted steering com-
puter, perform the necessary operations using the
Diagnostic tool (see Fault finding - Replacement
of components) (36B, Power-assisted steering). Note:
The support of the power-assisted steering com-
puter is not sold as a spare part. Always reuse
the support with the new computer.
127584

37A-31
MECHANICAL COMPONENT CONTROLS
Brake pedal: Removal - Refitting
RIGHT-HAND DRIVE, and 5-SPEED MANUAL GEARBOX
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the dashboard lower trim (1) ,
-the brake pedal switch (see 37A, Mechanical
component controls, Brake pedal switch: Re-
moval - Refitting, page 37A-42) .
aRemove the accelerator pedal (see 37A, Mechani-
cal component controls, Accelerator pedal: Re-
moval - Refitting, page 37A-29) .aRemove the clutch pedal switch (see ) .
aRemove the dashboard side face (2) .
aDisconnect the airbag inhibitor switch connector (3) . Equipment required
heat str ipper
Tightening torquesm
bolts of the « brake -
clutch pedal assembly » 21 N.m
123870
JB1
CRUISE CONTROL
123870
123871

37A-32
MECHANICAL COMPONENT CONTROLS
Brake pedal: Removal - Refitting
RIGHT-HAND DRIVE, and 5-SPEED MANUAL GEARBOX
37A
aRemove:
-the clutch master cylinder rod (4) ,
-the nuts (5) from the clutch master cylinder sup-
port,
-the clutch master cylinder support (6) ,
-the connecting clip (7) between the outlet pipe and
the clutch master cylinder,
-the clutch master cylinder (8) .aRemove the dashboard bolts (9) .
aMove the dashboard away slightly.
II - REMOVAL OPERATION FOR THE ALUMINIUM
PEDAL PADS
aHeat the pedal pad with a heat stripper to a maxi-
mum temperature of 80˚C.
aRemove the pad using a pair of pliers.
aClean the residue of adhesive on the pedal (see
Tools for stripping very thick soft mastic: Use) . JH3 or JR5
123904
123871
EQUIPMENT LEVEL SPORT

37A-36
MECHANICAL COMPONENT CONTROLS
Brake pedal: Removal - Refitting
RIGHT-HAND DRIVE, and 5-SPEED MANUAL GEARBOX
37A
aBond the pedal pad (19) to the pedal (20) by press-
ing on the right-hand side.
Press the pad to ensure bonding.
IV - FINAL OPERATION
aFit the dashboard.
aRefit the dashboard bolts.
aConnect the airbag inhibition switch connector.
aRefit the dashboard side panel.
aRefit:
-the clutch master cylinder,
-the connecting clip between the outlet pipe and the
clutch master cylinder,
-the clutch master cylinder support,
-the clutch support bolts,
-the clutch master cylinder rod.aRefit the clutch pedal switch (see ) .
aRefit the accelerator pedal (see 37A, Mechanical
component controls, Accelerator pedal: Remov-
al - Refitting, page 37A-29) .
aRefit:
-the brake pedal switch (see 37A, Mechanical
component controls, Brake pedal switch: Re-
moval - Refitting, page 37A-42) ,
-the dashboard lower trim.
135017
Note:
Respect the range of motion when fitting.
JH3 or JR5
CRUISE CONTROL
JB1

37A-37
MECHANICAL COMPONENT CONTROLS
Brake pedal: Removal - Refitting
5-SPEED MANUAL SEQUENTIAL GEARBOX
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery: Removal - Re-
fitting) .
aMark the routing of the dashboard wiring harness on
the pedals.
a
Disconnect:
-the accelerator pedal potentiometer connector,
-the electric steering computer supply connector.
aDetach the dashboard wiring harness from the ped-
als.
aMark the brake light switch wiring routing on the ped-
als.
aDetach the brake light switch wiring from the pedals.
aRemove the brake light switch (see 37A, Mechani-
cal component controls, Brake pedal switch: Re-
moval - Refitting, page 37A-42) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the connecting shaft (1) between the brake pedal
and the brake servo rod, after tilting the connecting
shaft upwards, move the ring using a flat-blade
screwdriver,
-the brake pedal plate nuts (2) ,
-the « brake pedal - brake pedal plate » assembly. Tightening torquesm
brake pedal plate nuts21 Nm
RIGHT-HAND DRIVE
LEFT-HAND DRIVE
122227
109205

37A-38
MECHANICAL COMPONENT CONTROLS
Brake pedal: Removal - Refitting
5-SPEED MANUAL SEQUENTIAL GEARBOX
37A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aThe shaft connecting the brake servo pushrod and
the brake pedal must be replaced every time it is re-
moved.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « brake pedal - brake pedal plate » assembly,
-the brake pedal plate nuts (2) .
aTorque tighten the brake pedal plate nuts (21 Nm).
aRefit the connecting shaft (1) between the brake
pedal and the brake servo rod from right to left and
from top to bottom.
III - FINAL OPERATION.
aRefit the brake light switch (see 37A, Mechanical
component controls, Brake pedal switch: Re-
moval - Refitting, page 37A-42) .
aRefit the brake light switch wiring in the position
marked during the removal operation.a
Connect:
-the accelerator pedal potentiometer connector,
-the electric steering computer supply connector.
aRefit the dashboard wiring harness in the position
marked during removal.
aConnect the battery (see Battery: Removal - Refit-
ting) .
109205
LEFT-HAND DRIVE
RIGHT-HAND DRIVE

37A-52
MECHANICAL COMPONENT CONTROLS
Clutch pedal switch: Removal - Refitting
CRUISE CONTROL, and 5-SPEED MANUAL GEARBOX
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the dashboard glovebox.
aDisconnect the connector (2) from the clutch pedal
switch.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTurn the clutch pedal switch (3) a quarter of a turn
anti-clockwise
aRemove the clutch pedal switch from the pedal. Equipment required
Diagnostic tool
119506
119507
121349