2009 RENAULT TWINGO RS wheel

37A-80
MECHANICAL COMPONENT CONTROLS
Brake servo: Check
RIGHT-HAND DRIVE
37A
aConnect a vacuum pump to the end of the non-re-
turn valve.
aActivate the vacuum pump to obtain a vacuum of
500 mbar.
aCheck that the vacuum pressure does not drop. If it
does, the non-return valve is pierced; replace the
valve (see 37A, Mechanical component controls,
Brake servo non-return valve: Removal - Refit-
ting, page 37A-11) .
aRefit the non-return valve pipe on the intake distribu-
tor.V - CHECKING THE VACUUM PUMP
aConnect the external vacuum pump to the engine
vacuum pump.
aStart the engine.
aCheck the following values:
-550 mbar in 5 seconds for an engine speed of 700
rpm,
-700 mbar in 3 seconds and 900 mbar in 5 sec-
onds for an engine speed of 4050 rpm.
aReplace the vacuum pump if the values are different
(see 37A, Mechanical component controls, Vacu-
um pump: Removal - Refitting, page 37A-25) .
aRefit the non-return valve pipe onto the vacuum
pump.
VI - FINAL OPERATION.
aRefit:
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection),
-the front right-hand wheel (see 35A, Wheels and
tyres, Wheel: Removal - Refitting, page 35A-1) .
123907
D4F or D7F
K9K
106889

38C-1
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: List and location of components38C
The anti-lock braking system pump assembly is
equipped with a 26-track computer.
102311
(1) Master cylinder pr imar y circuit
(2) Circuit for front left-hand wheel
(3) Circuit for front right-hand wheel
(4) Master cylinder secondary cir-
cuit
(5) Circuit for rear right-hand wheel
(6) Circuit for rear left-hand wheel
19113
(7) Braking computer
(8) Hydraulic assembly

38C-2
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
K9K, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture).aRemove:
-the bolts (1) from the lifting eye on the right-hand
side,
-the lifting eye on the right-hand side (2) ,
-the rigid pipe (3) from the EGR circuit.
aRemove the clip (4) from the soundproofing.
aMove the soundproofing aside (5) to access the hy-
draulic unit. Equipment required
pedal press
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
hydraulic unit inter medi-
ate bracket bolts on the
main hydraulic unit
mounting6.5 Nm
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
112329
121358

38C-4
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
K9K, and LEFT-HAND DRIVE
38C
aRemove:
-the hydraulic assembly intermediate bracket bolts
(10) ,
-the « hydraulic unit intermediate bracket - hydraulic
unit » assembly (11) from the main mounting,
-the hydraulic unit bolts (12) from its intermediate
bracket,
-the hydraulic unit from its intermediate bracket.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the hydraulic unit onto its intermediate bracket,
-the hydraulic unit bolts onto its intermediate brack-
et.
aTorque tighten the hydraulic unit bolts on its inter-
mediate bracket (8 Nm).
aRefit:
-the « hydraulic unit intermediate bracket - hydraulic
unit » assembly onto the main mounting,
-the hydraulic unit intermediate bracket bolts onto
the main hydraulic unit mounting.
aTorque tighten the hydraulic unit intermediate
bracket bolts on the main hydraulic unit mount-
ing (6.5 Nm).aRefit:
-the « hydraulic unit mounting - hydraulic unit » as-
sembly on the body,
-the hydraulic unit main mounting bolts on the body.
aTorque tighten the hydraulic unit main mounting
bolts on the body (8 Nm).
II - FINAL OPERATION.
aRemove the blanking plugs.
aFit and tighten the rigid brake pipe unions on the hy-
draulic unit.
aTorque tighten the rigid brake pipe unions on the
hydraulic unit (13 Nm).
aConnect the computer connector on the hydraulic
unit.
aFit the bulkhead soundproofing.
aRefit:
-the soundproofing clip,
-the rigid exhaust gas recirculation circuit pipe,
-the lifting eye on the right-hand side,
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
aRemove the pedal press from the brake pedal.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .
121456

38C-5
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F or D7F, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the ignition coil (see Coils: Removal - Refitting)
(MR 411, 17A, Ignition),
-the fuel vapour recirculation circuit solenoid valve
(see Fuel vapour absorber: Removal - Refitting)
(MR 411, 14A, Emission control),
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture).aDisconnect the hydraulic unit computer connector
(1) .
aUndo the rigid brake pipe unions (2) on the hydraulic
unit.
aInsert the blanking plugs. Equipment required
pedal press
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
hydraulic unit inter medi-
ate bracket bolts on the
main hydraulic unit
mounting6.5 Nm
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
121359
121360
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.

38C-7
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F or D7F, and LEFT-HAND DRIVE
38C
-the hydraulic unit main mounting bolts on the body.
aTorque tighten the hydraulic unit main mounting
bolts on the body (8 Nm).
II - FINAL OPERATION.
aRemove the blanking plugs.
aFit and tighten the rigid brake pipe unions on the hy-
draulic unit.
aTorque tighten the rigid brake pipe unions on the
hydraulic unit (13 Nm).
aConnect the computer connector on the hydraulic
unit.
aRefit:
-the air filter box (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the fuel vapour recirculation circuit solenoid valve
(see Fuel vapour absorber: Removal - Refitting)
(MR 411, 14A, Emission control),
-the ignition coil (see Coils: Removal - Refitting)
(MR 411, 17A, Ignition),
-the front wheel arch liner, on the passenger side
(see Front wheel arch liner: Removal - Refitting)
(MR 412, 55A, Exterior protection),
-the front wheel on the passenger side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
aRemove the pedal press from the brake pedal.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .

38C-8
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F, and 780, and LEFT-HAND DRIVE – K4M, and LEFT-HAND DRIVE
38C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aPosition the pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove:
-the passenger side front wheel (see 35A, Wheels
and tyres, Wheel: Removal - Refitting, page
35A-1) ,
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion).
aRemove the air filter housing (see Air filter unit: Re-
moval - Refitting) (12A, Fuel mixture).aDisconnect the fuel vapour rebreathing solenoid
valve union (1) .
aRemove the fuel vapour rebreathing solenoid valve
(2) .
aRemove the bolts (3) from the bulkhead heat shield.
aMove the bulkhead heat shield (4) to one side. Equipment required
pedal press
refrigerant charging station
Tightening torquesm
hydraulic unit bolts on
its inter mediate bracket8 Nm
intermediate bracket
bolts on the hydraulic
unit main bracket8 N.m
hydraulic unit main
mounting bolts on the
body8 Nm
rigid brake pipe unions
on the hydraulic unit13 Nm
D4F, and 780
109625
122384

38C-10
ANTI-LOCK BRAKING SYSTEM
Hydraulic brake unit: Removal - Refitting
D4F, and 780, and LEFT-HAND DRIVE – K4M, and LEFT-HAND DRIVE
38C
aRemove:
-the hydraulic unit intermediate bracket bolts (10) ,
-the “intermediate bracket - hydraulic unit” assembly
from the main bracket,
-the hydraulic unit bolts,
-the hydraulic unit from its intermediate bracket.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the hydraulic unit on its intermediate bracket.
aTorque tighten the hydraulic unit bolts on its inter-
mediate bracket (8 Nm).
aRefit the "hydraulic unit intermediate bracket - hy-
draulic unit" assembly on the main bracket.
aTorque tighten the intermediate bracket bolts on
the hydraulic unit main bracket (8 N.m).
aRefit the "main bracket - hydraulic unit" assembly on
the body.
aRefit:
-the right-hand suspended engine mounting (see
Right-hand suspended engine mounting: Re-
moval - Refitting) (19D, Engine mounting),-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting).
aTorque tighten the hydraulic unit main mounting
bolts on the body (8 Nm).
aClip on the fuel pipes.
aRemove the blanking plugs.
aFit and tighten the rigid brake pipe unions on the hy-
draulic unit.
aTorque tighten the rigid brake pipe unions on the
hydraulic unit (13 Nm).
aConnect the hydraulic unit connector.
II - FINAL OPERATION.
aRefit the "dehydrator reservoir - expansion valve"
connecting pipe (see Dehydrator reservoir - ex-
pansion valve connecting pipe: Removal - Refit-
ting) (62A, Air conditioning).
aFill the refrigerant circuit using a refrigerant charg-
ing station (see Refrigerant circuit: Draining -
Filling) (62A, Air conditioning).
aRefit the bulkhead heat shield.
aFit the fuel vapour rebreathing solenoid valve.
aRefit the union on the fuel vapour rebreathing sole-
noid valve.
aRefit the air filter unit (see Air filter unit: Removal -
Refitting) (12A, Fuel mixture)
aRefit:
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front passenger side wheel (see 35A, Wheels
and tyres, Wheel: Removal - Refitting, page
35A-1) .
aRemove the pedal press from the brake pedal.
121456
K4M
K4M, and AIR CONDITIONING or CLIMATE CON-
TROL
D4F, and 780