2009 RENAULT TWINGO diagram

13B-2V6 MR-413-X44-13B000$010.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:Vehicle(s): CLIO III, MODUS, MEGANE II / SCENIC II, New
Twingo, Kangoo 2.Name of computer: DCM1.2 injection
Engines: K9K 718, 724, 740, 750, 752, 766, 768, 800, 802,
812Program No.: 4D
Function concerned: Direct diesel injection, DELPHI,
COMMON RAIL, MULTI INJECTION.Vdiag No.: 48, 4C, 50, 54, 58, 5C
Special tooling required
Diagnostic tool
Multimeter
Elé. 1590 112-track computer bornier
Elé. 1681 Universal bornier
Mot 1711 Injector flow measuring kit
For vehicles with radio frequency remote control/key,
switch on the ignition with the key.
For vehicles with a Renault card,
With the vehicle card in the card reader,
Press and hold the start button (+ 5 seconds) with starting conditions not met,
Connect the diagnostic tool and perform the required operations.
DCM1.2_V48_PRELI/DCM1.2_V4C_PRELI/DCM1.2_V50_PRELI/DCM1.2_V454_PRELI/DCM1.2_V58_PRELI/DCM1.2_V5C_PRELI
DIESEL INJECTION
Fault finding – Introduction

13B-29
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF001
PRESENT
OR STOREDCOOLANT TEMPERATURE SENSOR CIRCUITCO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
NOTESSpecial notes:
If fault DF001 is present, the preheating time is greater than 10 seconds and the engine
fan switches on at low speed (Fan assembly 1). If there is a fault on Fan assembly 1,
then on vehicles fitted with air conditioning, Fan assembly 2 switches on.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connection and condition of the coolant temperature sensor connector, component code 244.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of component 244 between connections 3JK and 3C.
If the resistance of the coolant temperature sensor is not:
at –40
°C: 68780 ΩΩ Ω Ω
< X < 82780 ΩΩ Ω Ω

at –10
°C: 11332 ΩΩ Ω Ω
< X < 13588 ΩΩ Ω Ω

at 25
°C: 2140 ΩΩ Ω Ω
< X < 2364 ΩΩ Ω Ω

at 50
°C: 772 ΩΩ Ω Ω
< X < 850 ΩΩ Ω Ω

at 80
°C: 275 ΩΩ Ω Ω
< X < 291 ΩΩ Ω Ω

at 110
°C: 112 ΩΩ Ω Ω
< X < 118 ΩΩ Ω Ω

at 120
°C: 86 ΩΩ Ω Ω
< X < 90 ΩΩ Ω Ω
,
replace the coolant temperature sensor, component code 244 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2) Mechanical, 19A, Cooling,
Coolant temperature sensor: Removal - Refitting).
Check the insulation and continuity of the following connections:
–3JK between components 120 and 244,
–3C between components 120 and 244.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the coolant temperature sensor, component code 244 (see MR 364 (Mégane II),
MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2) Mechanical,
19A, Cooling, Coolant temperature sensor: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF001/DCM1.2_V4C_DF001/DCM1.2_V50_DF001/DCM1.2_V54_DF001/DCM1.2_V58_DF001/DCM1.2_V5C_DF001
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-30
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF002
PRESENT
OR STOREDAIR TEMPERATURE SENSOR CIRCUITCO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
1.DEF: inconsistency
NOTESDepending on the engine type, the air temperature is given by the air temperature
sensor, which is either on the air flowmeter or in place of the air flowmeter on K9K 724,
740, 766, 768, and 812 engines only.
See the Technical Note Wiring Diagrams for the vehicle.
The air temperature sensor in the flow sensor has a separate electrical circuit.
Move the wiring between the computer and the air temperature sensor to see if a change of status occurs
(present stored).
Look for any wiring damage and check the connection and condition of the air temperature sensor and its
connections.
Check the connection and condition of the injection computer connector.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of component 272 between connections 3JQ and 3B.
If the resistance of the air temperature sensor is not:
(theoretical values for engines with flowmeter)
at -10
°C: 8716 ΩΩ Ω Ω
< X < 9688 ΩΩ Ω Ω
at 0
°C: 5497 ΩΩ Ω Ω
< X < 6051 ΩΩ Ω Ω
at 10
°C: 3553 ΩΩ Ω Ω
< X < 3875 ΩΩ Ω Ω
at 20
°C: 2353 ΩΩ Ω Ω
< X < 2543 ΩΩ Ω Ω
at 30
°C: 1613 ΩΩ Ω Ω
< X < 1729 ΩΩ Ω Ω
(theoretical values for engines without flowmeter)
at -10
°C: 8623 ΩΩ Ω Ω
< X < 10454 ΩΩ Ω Ω
at 25
°C: 1928 ΩΩ Ω Ω
< X < 2174 ΩΩ Ω Ω
at 50
°C: 763 ΩΩ Ω Ω
< X < 857 ΩΩ Ω Ω
,
replace the air temperature sensor.
DCM1.2_V48_DF002/DCM1.2_V4C_DF002/DCM1.2_V50_DF002/DCM1.2_V54_DF002/DCM1.2_V58_DF002/DCM1.2_V5C_DF002

13B-32
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF003
PRESENT
OR STOREDATMOSPHERIC PRESSURE SENSOR CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
NOTESSpecial note:
The atmospheric pressure sensor is incorporated in the computer.
See the Technical Note Wiring Diagrams for the vehicle.
Look for any wiring damage and check the condition and connection of the injection computer connectors,
component code 120.
Move the wiring between the injection computer, component code 120 and the battery, component code 107
to see if a change of status occurs (Present Stored).
Look for any wiring damage and check the connection and condition of the battery, component code 107
and its connections.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
Measure the battery voltage when the ignition is switched on.
If the battery voltage is less than 11 V, recharge the battery.
Check the connection and condition of the battery terminals and posts, component code 107.
Check the connection and condition of connector A (black 32-track) of the injection computer, component
code 120.
Check the connection and condition of the connector of the injection locking relay or of the UPC, according to
the vehicle.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
DCM1.2_V48_DF003/DCM1.2_V4C_DF003/DCM1.2_V50_DF003/DCM1.2_V54_DF003/DCM1.2_V58_DF003/DCM1.2_V5C_DF003

13B-34
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF005
PRESENT
OR STOREDENGINE SPEED SENSOR CIRCUIT1.DEF: Inconsistency
2.DEF: No signal
3.DEF: Too many additional teeth
4.DEF: Teeth missing
5.DEF: Additional teeth
6.DEF: Too many teeth missing
NOTESSpecial note:
If 1.DEF, 2.DEF, 3.DEF, or 6.DEF is present: the engine stops and the level 2 warning
light illuminates, with the message Faulty injection displayed on the instrument panel.
If 4.DEF or 5 DEF is present: the engine performance is reduced to 75% and the level
1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present when the starter motor is operating or the engine is running at idle
speed.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connection and condition of the engine speed sensor connector, component code 149.
Check the connection and condition of connector B of the injection computer, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the engine speed sensor, component code 149 between connections 3BL and 3BG.
If the resistance of the engine speed sensor, component code 149 is not between 510 Ω et 850 Ω (at 20
°C), replace
the engine speed sensor (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR
411 (New Twingo), MR 417 (Kangoo 2) Mechanical, 13B Diesel injection, Crankshaft position sensor:
Removal - Refitting).
Check the insulation and continuity of the following connections:
–3BG between components 149 and 120,
–3BL between components 149 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the engine speed sensor, component code 149 (see MR 364 (Mégane II),
MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2) Mechanical,
13B Diesel injection, Crankshaft position sensor: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF005/DCM1.2_V4C_DF005/DCM1.2_V50_DF005/DCM1.2_V54_DF005/DCM1.2_V58_DF005/DCM1.2_V5C_DF005

13B-35
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF007
PRESENT
OR STOREDRAIL PRESSURE SENSOR CIRCUITCC.0: Short circuit to earth
C0.1: Open circuit or short circuit to +12 V
1.DEF: Inconsistency
2.DEF: Below minimum threshold
3.DEF: Above maximum threshold
4.DEF: Value outside permitted tolerance
NOTESPriority for dealing with a combination of faults:
–DF113 Sensor supply voltage.
Conditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine starts.
Special note:
If fault DF007 is present: the engine stops and cannot be restarted and the level 2
warning light illuminates, with the message Faulty injection displayed on the
instrument panel.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connection and condition of the rail pressure sensor connector, component code 1032.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +5 V on connection 3LX of component 1032.
Check for earth on connection 3LZ of component 1032.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3LX between components 1032 and 120,
–3LY between components 1032 and 120,
–3LZ between components 1032 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_DF007/DCM1.2_V4C_DF007/DCM1.2_V50_DF007/DCM1.2_V54_DF007/DCM1.2_V58_DF007/DCM1.2_V5C_DF007

13B-37
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF008
PRESENT
OR STOREDPEDAL POTENTIOMETER CIRCUIT GANGED CIRCUIT 1CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
1.DEF: Inconsistency between pedal gangs 1 and 2
2.DEF: No signal
3.DEF: Jammed component
NOTESPriority for dealing with a combination of faults:
–DF113 Sensor supply voltage.
Special note:
If fault DF008 is present: the idle speed is fast (1000 rpm), the engine performance is
reduced to 75%, and the level 1 warning light illuminates with the message Check
injection displayed on the instrument panel.
If DF008 and DF009 Pedal potentiometer circuit gang 2 are present: the engine
speed increases to 1300 rpm or 1700 rpm if the vehicle is fitted with a sequential
gearbox (fault on gangs 1 and 2), and the level 1 warning light illuminates with
the message Check injection displayed on the instrument panel.
Note: possible risk of the engine speed racing with no load for 1 second.
See the Technical Note Wiring Diagrams for the vehicle.
1.DEF
3.DEF
NOTESNone.
Disconnect connector A (black) of the injection computer, component code 120 and the connector of the pedal
potentiometer, component code 921.
Check the insulation between connections 3LS and 3LW of component 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the accelerator pedal potentiometer, component code 921 (see MR 364
(Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2),
Mechanical, 13B, Diesel injection, Accelerator pedal potentiometer: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF008/DCM1.2_V4C_DF008/DCM1.2_V50_DF008/DCM1.2_V54_DF008/DCM1.2_V58_DF008/DCM1.2_V5C_DF008

13B-40
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF009
PRESENT
OR STOREDPEDAL POTENTIOMETER TRACK 2 CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
NOTESPriority for dealing with a combination of faults:
–DF122 Pedal potentiometer gang 2 supply voltage.
Special note:
If fault DF009 is present: the idle speed is fast (1000 rpm), the engine performance is
reduced to 75%, and the level 1 warning light illuminates with the message Check
injector displayed on the instrument panel.
If DF009 and DF008 Pedal potentiometer circuit gang 1 are present: the engine
speed increases to 1300 rpm or 1700 rpm if the vehicle is fitted with a sequential
gearbox (fault on gangs 1 and 2), and the level 1 warning light illuminates with
the message Check injection displayed on the instrument panel.
Note: possible risk of the engine speed racing with no load for 1 second.
See the Technical Note Wiring Diagrams for the vehicle.
CO.0
NOTESSpecial note:
None.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of connector A (black 32-track) of the computer, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + 5 V on connection 3LU of component 921.
Check for earth on connection 3LV of component 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Disconnect connector A of the computer, component code 120 and the connector of the pedal potentiometer,
component code 921.
Check the insulation against earth of connection 3LW on component 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DCM1.2_V48_DF009/DCM1.2_V4C_DF009/DCM1.2_V50_DF009/DCM1.2_V54_DF009/DCM1.2_V58_DF009/DCM1.2_V5C_DF009