2009 RENAULT TWINGO engine

1Engine and peripherals
V1 MR-413-X44-86D000$TOC.mif
V1
86D
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V1
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2008
MULTIMEDIA CONNECTION UNIT
BICVdiag No.: 14
Fault finding – Introduction 86D - 2
Fault finding – List and location of components 86D - 8
Fault finding – Role of components 86D - 12
Fault finding – Function 86D - 13
Fault finding – Configurations 86D - 14
Fault finding – Programming 86D - 15
Fault finding – Replacement of components 86D - 16
Fault finding – Fault summary table 86D - 17
Fault finding – Interpretation of faults 86D - 18
Fault finding – Conformity check 86D - 28
Fault finding – Status summary table 86D - 32
Fault finding – Interpretation of statuses 86D - 33
Fault finding – Parameter summary table 86D - 37
Fault finding – Command summary table 86D - 38
Fault finding – Customer complaints 86D - 39
Fault finding – Fault Finding Chart 86D - 40

86D-22
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF005
CONTINUED
2.DEFNOTESNone.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the condition of fuse F48 (15 A) for New Twingo or fuses F14 (5 A), F2 (20 A), and unit fuse 710 (15 A) for
Clio III.
Check the connection and condition of the connectors of the display computer, component code 653 or of the
multimedia connection unit computer, component code 1714, depending on the vehicle equipment.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the computer connector and check the conformity of the following connections:
–BCP4 between components 260 and 653 or 1714,
–BPT between components 645 and 653 or 1714,
–BPT3 between components 260 and 653 or 1714,
–NAM between component 653 or 1714 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.

86D-28V1 MR-413-X44-86D000$100.mif
86D
BIC
Vdiag No.: 14
MAIN SCREEN
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay
and notesFault finding
Side lightsET004:+12 V Side
lightsINACTIVE
INVALID
OFF
ONIn the event of an inconsistency,
run fault finding on the UCH (see
87B, Passenger compartment
connection unit).
BIC_V14_CCONF
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check

86D-29V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET002:Radio on/off buttonINACTIVE
ACTIVE
This status remains
active until the ignition is
switched off.In the event of an
inconsistency, run fault
finding on the radio (see 86A,
Radio)
Battery voltagePR002:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF005
Supply.
Vehicle speedPR003:Vehicle speedIndicates the vehicle
speed in mph (km/h).In the event of an
inconsistency, run fault
finding on the ABS (see 38C,
Anti-lock braking system).
External
temperaturePR004External
temperature-40˚C < X < 60˚CIn the event of an
inconsistency, run fault
finding on the UCH (see 87B,
Passenger compartment
connection unit).
System activationAC002:On - Off ButtonUsed to simulate the On -
Off Button of the radioIn the event of an
inconsistency, consult the
interpretation of fault DF006
Activation signal and run
fault finding on the radio (see
86A, Radio).

86D-30V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA (CONTINUED)
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET009:Repeat button
(only on Clio III)
PRESSED
RELEASEDIn the event of an
inconsistency, consult the
interpretation of status
ET009.
ET020:Mute buttonIn the event of an
inconsistency, consult the
interpretation of status
ET020.
ET011:+ buttonIn the event of an
inconsistency, consult the
interpretation of status
ET011.
ET012:- buttonIn the event of an
inconsistency, consult the
interpretation of status
ET012.
ET023:Source buttonIn the event of an
inconsistency, consult the
interpretation of status
ET023.
ET024:Mode button In the event of an
inconsistency, consult the
interpretation of status
ET024.
ET025:Telephone button In the event of an
inconsistency, consult the
interpretation of status
ET025.
Wheel actionET017:Wheel actionUPWARDS
DOWNWARDS
INACTIVEIn the event of an
inconsistency, consult the
interpretation of status
ET017.

86D-31V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: DISPLAY
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
DisplayAC001:Display testThis command is used
to test the liquid crystal
screen of the display.None
LightingET004:+12 V Side lightsOFF
ON
INVALID
INACTIVEIn the event of an
inconsistency, run fault
finding on the UCH (see
87B, Passenger
compartment
connection unit).
ET007:BrightnessPANEL GAP
NIGHTIn the event of an
inconsistency, consult the
interpretation of ALP 4
Lighting does not
change when the
vehicle lights are
switched on.