2009 RENAULT TWINGO ECO mode

86A-27V1 MR-413-X44-86A150$060.mif
86A
R2-08
Vdiag No.: 64
Thermal protection
Thermal protection is integrated in order to protect the radio.
The functions are restored when the internal temperature falls below 80˚C.
Car radio code
The radio is protected by a two-part anti-theft system:
•A 4-digit code,
•Information exchanged between the instrument panel and the radio.
This code is requested in the following cases:
•New vehicle,
•New radio,
•When a radio is swapped between vehicles.
Entering the code using the radio control satellite:
Press the lower button on the radio control satellite to confirm an entry.
Entering using the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then confirm with button 6.
If the code is entered incorrectly, the radio will be locked (1 minute for the first error, 2 minutes for the second error,
4 minutes for the third error, etc., for a maximum of 32 minutes after each attempt).
After several attempts, if the fault is still present, contact the Techline.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered
(with regular warning beeps).
Note:
If the battery is disconnected, it is not necessary to re-enter the radio anti-theft code.
RADIO
Fault finding – Anti-theft code

86A-29V1 MR-413-X44-86A150$080.mif
86A
R2-08
Vdiag No.: 64
Available configuration and operating mode
SC002: Computer configuration
This command is used to configure the computer according to the vehicle equipment, type of driving and language.
Configuration modification procedure:
•Activate the + after ignition feed.
•Connect the diagnostic tool and switch on the radio.
•Establish dialogue with the computer.
•Select the Repair mode menu.
•Select the Configuration and programming menu.
•Select the special command SC002 Computer configuration.
•Select the connection in the drop-down menu that corresponds to the vehicle.
•Click on Confirm.
•Exit diagnostic mode (ends dialogue with the computer without switching off the tool), switch off the ignition for
30 seconds and then switch the ignition back on.
•Establish dialogue with the computer.
•Check to see that the configurations have been correctly stored in the Configuration reading menu.
NOTE:
To reconfigure the computer, delete any telephones already paired to the radio (using the menus, see the user's
manual), before running configuration SC002 Computer configuration.
RADIO
Fault finding – Configurations

86A-56
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF055
PRESENT
OR
STOREDBUTTON JAMMED
1.DEF: Radio front panel button jammed.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
The button concerned is pressed for at least 2 minutes,
Check the conformity of the radio buttons by consulting the following statuses:
–ET002 Mode button,
–ET003 Right directional button,
–ET004 Left directional button,
–ET009 CD eject button,
–ET010 Radio preset button 1,
–ET011 Radio preset button 2,
–ET012 Radio preset button 3,
–ET013 Radio preset button 4,
–ET014 Radio preset button 5,
–ET015 Radio preset button 6,
–ET034 Rewind button,
–ET035 Fast forward button,
–ET036 Wheel press on/off,
–ET039 TEL button,
–ET040 SET button,
–ET060 Centre wheel press,
–ET062 Text info button,
–ET063 MEM button,
–ET064 Radio/CD button.
If the one of the statuses is Pressed, press on the corresponding button so that the status becomes Released.
R208_V64_DF055

86A-82
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 2 The radio beeps every 2 seconds
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
The radio beeps every 2 seconds.
The radio is in factory mode.
Wait for 2 minutes for the radio to request
the code.
Does the radio request the code?
Enter the radio security code (see Anti-theft
code).
Is the code correct?If the radio displays a countdown in seconds, then
the code that was entered is incorrect.
Wait for the time indicated on the display for the
radio to request the code, then enter the correct
code.
The problem disappears.Was the code accepted?
Contact the Techline.
NO
YES
NO
YES
YES
NO
R208_V64_ALP2