2009 RENAULT TWINGO display

86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064

86A-49V2 MR-413-X44-86A100$130.mif
86A
R01-08
Vdiag No.: A4
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
SupplyPR011:Battery
voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
R108_VA4_CCONF
RADIO
Fault finding – Conformity check

86A-50V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel buttonET010:Radio preset
button 1PRESSED RELEASEDIn the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed.
ET011:Radio preset
button 2PRESSED RELEASED
ET012:Radio preset
button 3PRESSED RELEASED
ET013:Radio preset
button 4PRESSED RELEASED
ET014:Radio preset
button 5PRESSED RELEASED
ET015:Radio preset
button 6PRESSED RELEASED
ET008:Radio on/off
buttonPRESSED RELEASED
ET009:CD eject buttonPRESSED RELEASED

86A-51V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel button
(continued)ET071:Up buttonPRESSED RELEASEDIn the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed.
ET072:Down buttonPRESSED RELEASED
ET070:"OK" buttonPRESSED RELEASED
ET069:Volume "-" buttonPRESSED RELEASED
ET068:Volume "+" buttonPRESSED RELEASED

86A-52V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel button
(continued)ET063:"MEM" buttonPRESSED RELEASED
In the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed. ET005:Source buttonPRESSED RELEASED
ET007:Traffic info buttonPRESSED RELEASED
ET073:Left-hand buttonPRESSED RELEASED
ET074:Right-hand buttonPRESSED RELEASED
CD ejectionAC013:CD ejectionThis command is used for
testing CD ejection from
the CD player.In the event of an
inconsistency, contact the
Techline.
SupplyPR011:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
Computer
activationET065:Activation requestACTIVE INACTIVE
In the event of an
inconsistency, consult the
interpretation of fault DF064
Activation signal.
ET057:Activation signalACTIVE INACTIVE

86A-53V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: AUDIO
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Audio testAC004:Test right front
speaker line
This command is used to
successively activate
each speaker.In the event of an
inconsistency, consult the
interpretation of fault DF001
Front right-hand speaker.
AC005:Test left front
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF002
Front left-hand speaker.
AC006:Test right rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF003
Rear right-hand speaker.
AC007:Test left rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF004
Rear left-hand speaker.

86A-54V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
FUNCTION: WIRELESS COMMUNICATIONS
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Radio
receptionPR005:Radio
field
intensity0 dBµV inconsistency, consult the
interpretation of parameter
PR005.

86A-57
AFTER REPAIRRepeat the conformity check from the start.
V2 MR-413-X44-86A100$160.mif
RADIO
Fault finding – Interpretation of parameters86A
R01-08
Vdiag No.: A4
PR005RADIO FIELD INTENSITY
NOTESThe values shown in this conformity check are given as a guide.
Test conditions: Engine off, ignition on and radio on.
Perform the conformity check outside, in an area with good radio reception
and without obstacles.
Conformity check:
Monitor the PR005 value of the diagnostic tool data display.
Display of frequency received for the radio station currently set.
Radio field intensity parameterRadio reception level
(data display)
Outdoor testUnit: dBµV
Data interpretation:
Radio reception value Status
X > 18 dBµVCorrect radio reception
14 dBµV < X < 18 dBµVCorrect sound quality
RDS decoding (for example: display of
station names) correct
Automatic synchronisation / Presence in
the radio list
not satisfactory
10 dBµV < X < 14 dBµVCorrect sound quality
RDS decoding (for example: display of
station names) not satisfactory
Automatic synchronisation / Presence in
the radio list
not satisfactory
X > 10 dBµVRadio reception not satisfactory
If the fault is still present, contact the Techline.
R108_VA4_PR005
RADIO
Fault finding – Interpretation of parameters