2009 RENAULT TWINGO Valve

17B-246V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET568TYPE 5 DEFECT MODE
STATUS
DEFINITIONACTIVE: This status indicates that defect mode type 5 is active.
INACTIVE: This status indicates that defect mode type 5 is inactive.
NOTESThere must be no present or stored faults.
This type groups together faults affecting the pressure, the throttle valve control by the torque structure and the
turbocharging pressure.
Its effect is to go into pedal feedback mode instead of the permanent torque structure. The ESP and cruise control/
speed limiter systems are deactivated. The automatic or sequential gearbox goes into safe mode. The engine
management no longer accepts requests from the gearbox, and sends torque values by default to the multiplex
network.
SIM32_V44_ET568/SIM32_V4C_ET568/SIM32_V50_ET568/SIM32_V54_ET568
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-263V7 MR-413-X44-17B000$160.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* OCR: Opening cyclic ratio
* EV: Solenoid valve
* mot: motorised
* app.: applying
* AAC: Camshaft
Tool ParameterDiagnostic tool title
PR014Idling speed correction
PR015Engine torque
PR018Estimated air flow
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure
PR041Turbocharger pressure (Vdiag 54 only)
PR055Engine speed
PR059Inlet air temperature
PR064Coolant temperature
PR071Computer feed voltage
PR089Vehicle speed
PR090Idle speed regulation programming value
PR091OCR* Theoretical idle speed regulation
PR094AAC* dephaser OCR* setpoint (Vdiag 4C only)
PR095Anti-pinking correction
PR096Mot.* throttle upper stop programmed value.
PR097Mot.* throttle lower stop programmed value.
PR098Upstream oxygen sensor voltage
PR099Downstream oxygen sensor voltage
PR101Duration of injection
PR102Canister bleed solenoid valve OCR*
PR103Instantaneous fuel consumption
PR104Turbocharging EV* OCR* (Vdiag 54 only)
PR105Mileometer OBD fault warning light lit
PR106Mileometer fault warning light lit
PR111Motorised throttle position corrected value.
PR113Lower throttle stop after app.* offset
PR116Motorised throttle corrected position setpoint
PR118Measured throttle position gang 1
PR119Measured throttle position gang 2
PETROL INJECTION
Fault finding – Parameter summary table

17B-274V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR041
CONTINUED
–Check the cleanliness of the air filter.
–Replace the filter if necessary.
–Check that the air inlet circuit is not blocked.
The turbocharging system must be perfectly sealed, from the exhaust manifold to the turbocharger, from the
turbocharger to the heat exchanger and from the heat exchanger to the throttle valve.
Check that there are no air leaks:
–around the turbocharger pressure sensor,
–around the air temperature sensor.
Check absence of leaks in the wastegate capsule pressure circuit connected to the turbocharger system.
Check that the air-air heat exchanger is not clogged (presence of oil).
If there is oil in the heat exchanger, the turbocharger is certainly damaged.
Using a pressure/vacuum pump, check that the turbocharger protection and turbocharging valve capsule
diaphragms do not leak.
Check the condition the motorised throttle valve in terms of clogging.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-284V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* MOT.: motorised
PR096MOT.* THROTTLE VALVE UPPER STOP PROGRAMMED VALUE
PARAMETER
DEFINITIONThis parameter indicates the programmed throttle valve upper stop value as a %.
NOTESThere must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
The value should be:
PR096 ≈ 19%.
If there is a fault, apply interpretation for ET051 Throttle stop programming.
SIM32_V44_PR096/SIM32_V4C_PR096/SIM32_V50_PR096/SIM32_V54_PR096
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-285V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* MOT.: motorised
PR097MOT.* THROTTLE VALVE LOWER STOP PROGRAMMED VALUE
PARAMETER
DEFINITIONThis parameter indicates the programmed throttle valve lower stop value in %.
NOTESThere must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
The value should be:
PR097 ≈ 9%.
If there is a fault, apply interpretation for ET051 Throttle stop programming.
SIM32_V44_PR097/SIM32_V4C_PR097/SIM32_V50_PR097/SIM32_V54_PR097
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-289V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* ocr = opening cyclic ratio
PR102CANISTER BLEED SOLENOID VALVE OCR*
PARAMETER
DEFINITIONThis parameter indicates the canister bleed solenoid valve opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
The value should be:
PR102 ≈ 0%
SIM32_V44_PR102/SIM32_V4C_PR102/SIM32_V50_PR102/SIM32_V54_PR102
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-291V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
(Vdiag 54 only)
* OCR: opening cycle ratio
* EV: Solenoid valve
PR104Turbocharging EV* OCR* setpoint
PARAMETER
DEFINITIONThis parameter indicates the turbocharging solenoid valve opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
This percentage is 0% and increases according to the engine load.
SIM32_V54_PR104
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-295V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* App.: application
PR113THROTTLE LOWER STOP AFTER OFFSET APP.*
PARAMETER
DEFINITIONThis parameter is for viewing the throttle valve lower stop after offset application as a %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
The value should be:
PR113 ≈ 10%.
In the event of a fault, apply the interpretation of DF095 Throttle potentiometer circuit gang 1 and DF096
Throttle potentiometer circuit gang 2.
SIM32_V44_PR113/SIM32_V4C_PR113/SIM32_V50_PR113/SIM32_V54_PR113
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.