2009 RENAULT TWINGO ABS

17B-235V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET556DRIVER'S DEACTIVATION OF THE CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONSTATUS 1: This status indicates that the cruise control/speed limiter function is
deactivated each time the brake pedal is depressed.
STATUS 2: This status indicates that the cruise control/speed limiter function is
deactivated after the suspend button is pressed.
STATUS 3: This status indicates that the cruise control/speed limiter function is
deactivated after the clutch pedal is depressed.
STATUS 4: This status indicates that the deactivation of the cruise control/speed
limiter function is deactivated after the gear lever is put into neutral.
NOTESCruise control remains deactivated as long as the vehicle speed does not exceed
a speed V >18 mph (30 km/h).
IMPORTANT
Certain deactivations are stored by the computer.
To reinitialise this status, run RZ001 Fault memory.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
STATUS 1 Brake pedal depressed
If status ET556 becomes STATUS 1 if the cruise control function is deactivated when
the brake pedal is depressed.
Run fault finding on the ABS circuit (see 38C, Anti-lock braking system).
STATUS 2 Cancel button pressed
Status ET556 changes to STATUS 3 when driving, with cruise control active, if the
driver presses the cruise control/speed limiter 0 button.
If status ET556 becomes STATUS 3 without pressing cruise control/speed limiter
button 0, run fault finding on the cruise control/speed limiter control button R/0.
SIM32_V44_ET556/SIM32_V4C_ET556/SIM32_V50_ET556/SIM32_V54_ET556
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-238V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET557
CONTINUED 1
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
STATUS 1 Invalid vehicle speed
If status ET557 changes to STATUS 1 if the vehicle speed received by the computer
is invalid.
In the event of any faults, run fault finding on the ABS computer (see 38C, Anti-lock
braking system).
If the fault is still present, contact the Techline.
STATUS 2 Fault detected by the injection computer
If status ET557 changes to STATUS 2 if the injection computer detects a fault on the
injection system:
–Faults on the accelerator pedal.
–Engine speed sensor or camshaft faults.
–Engine speed greater than 4700 rpm.
–Engine speed less than 1000 rpm.
Carry out a multiplex network test, then an injection system test, and carry out fault
finding on any faults.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-239V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET557
CONTINUED 2
STATUS 3 Cruise control or speed limiter fault
If status ET557 is STATUS 3, consult the interpretation of status ET042 Cruise
control/speed limiter, to test the cruise control system components and find the
faulty component.
If status ET557 changes to STATUS 3, deal with the faults present or stored in the
computer.
If the fault is still present, contact the Techline.
STATUS 4 Invalid vehicle speed
If status ET557 changes to STATUS 4 if the vehicle speed received by the computer
is not consistent with the request.
In the event of any faults, run fault finding on the ABS computer (see 38C, Anti-lock
braking system).
If the fault is still present, contact the Techline.
STATUS 5 Traction control request
If the vehicle being diagnosed is fitted with traction control, the cruise control function
is deactivated each time traction control is selected.
Status ET557 changes to STATUS 5, when driving, with cruise control active and
traction control requested.
Status ET557 changes to STATUS 5 without a traction control request (see 38C,
Anti-lock braking system).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-241V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET562FAN ASSEMBLY REQUEST BY AUTOMATIC TRANSMISSION (applies only for the sequential gearbox on engine D4F 772)
STATUS
DEFINITIONPRESENT: This status indicates that there has been a fan assembly request from the
transmission.
ABSENT: This status indicates that there has not been a fan assembly request from the
transmission.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
PRESENT
or
ABSENTThe status is PRESENT or ABSENT depending on the computer program (engine oil
temperature).
SIM32_V44_ET562/SIM32_V4C_ET562/SIM32_V50_ET562/SIM32_V54_ET562
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-261V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET704
ET705
CONTINUED
Sensor electrical conformity
ACTIVE
or
INACTIVE
If the brake lights are working:
–Check the continuity and the absence of interference resistance of the
following connections:
●5A between components 160 and 120/645/119 (for NEW TWINGO or E33)
●65A between the components 160 and 120/645/119 (for CLIO III or MODUS).
If the connections are faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
If the brake lights are not operational, check:
–the condition and fitting of the brake switch,
–the condition and conformity of the brake lights fuse.
–the conformity of the values in the following tables:
Continuity
between
connectionsInsulation
between
connections
Switch
pressed
(Brake pedal
released)For CLIO III or
MODUS5A and SP13 65G and AP10
For NEW
TWINGO or E335A and AP10 65A and AP10
Switch
released
(Brake pedal
depressed)For CLIO III or
MODUS65G and AP10 5A and SP13
For NEW
TWINGO or E3365A and AP10 5A and AP10
Replace the switch if the values obtained are not correct.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-274V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR041
CONTINUED
–Check the cleanliness of the air filter.
–Replace the filter if necessary.
–Check that the air inlet circuit is not blocked.
The turbocharging system must be perfectly sealed, from the exhaust manifold to the turbocharger, from the
turbocharger to the heat exchanger and from the heat exchanger to the throttle valve.
Check that there are no air leaks:
–around the turbocharger pressure sensor,
–around the air temperature sensor.
Check absence of leaks in the wastegate capsule pressure circuit connected to the turbocharger system.
Check that the air-air heat exchanger is not clogged (presence of oil).
If there is oil in the heat exchanger, the turbocharger is certainly damaged.
Using a pressure/vacuum pump, check that the turbocharger protection and turbocharging valve capsule
diaphragms do not leak.
Check the condition the motorised throttle valve in terms of clogging.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-279V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR089VEHICLE SPEED
PARAMETER
DEFINITIONGives the vehicle speed in km/h.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
This parameter is transmitted by the ABS computer. This signal is transmitted to the
injection on the multiplex network.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
In the event of a fault, test the multiplex network (see 88B, Multiplex).
Then complete fault finding on the ABS computer (see 38C, Anti-lock braking system).
SIM32_V44_PR089/SIM32_V4C_PR089/SIM32_V50_PR089/SIM32_V54_PR089
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-299V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* AC: Air conditioning
PR125POWER ABSORBED BY THE AC* COMPRESSOR
PARAMETER
DEFINITIONThis parameter indicates the power consumed by the air conditioning compressor in W.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with the engine running and engine coolant temperature > 80˚C
The value should be:
PR125 > 300 W
Heating and air conditioning system engaged only with the engine running.
SIM32_V44_PR125/SIM32_V4C_PR125/SIM32_V50_PR125/SIM32_V54_PR125
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.