17B-258V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 3
DECREASE
Status ET703 becomes MINUS when the cruise control/speed limiter "-" button is
pressed. This button is on the steering wheel, on the left-hand side.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not change to DECREASE, check the condition of the cruise
control/speed limiter +/- button and check the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the "-" button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 100 Ω, check the continuity of the connection when the
button is in the rest position.
If there is continuity, replace the +/- control button.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter "0" button
is pressed. This button is located on the steering wheel, to the right.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not become SUSPEND, check the condition of the cruise
control/speed limiter "R/0" button and the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the "0" button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
17B-259V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 4
RESUME
Status ET703 becomes RESUME when the cruise control/speed limiter "R" button is
pressed. This button is located on the steering wheel, to the right.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not change to RESUME, check the status of the cruise control/
speed limiter R/0 button and the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the R button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 900 Ω, check the continuity of the connection when the
button is in the rest position.
If there is continuity, replace the R/0 control button.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
