2009 RENAULT TWINGO light

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 20V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF005
PRESENT
OR
STOREDRIGHT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
CC.1
CO.0
NOTES None
Remove the rear bumper and disconnect the 3-track connector on the right-hand inner detection sensor.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and the right hand inner sensor connectors (bent, oxidised or broken tabs).
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistances of the computer between the following connections:
Connection code 151Q,
●Connection code 151U.
The resistance should be 215 kΩΩ Ω Ω
± 10 kΩΩ Ω Ω
.
●Connection code 151Q,
●Connection code 151V.
The resistance should be 100 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
.
If the readings do not correspond to the above values or if there is a short circuit in the specified connections,
contact Techline.
Measure the resistance of component 1220 between the following connections:
●Connection code 151Q,
●Connection code 151U.
If the resistance value is not infinite, replace the right-hand inner sensor.
●Connection code 151Q,
●Connection code 151V.
If the resistance value is not 40 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
(wait a few seconds for the reading to stabilise), replace the right-hand
inner sensor.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF005/AAP_V08_DEF005

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 22V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF006
PRESENT
OR
STOREDBUZZER
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
The fault is indicated by the absence of the 1-second beep normally emitted by the
buzzer when reverse gear is selected.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and the buzzer connectors (bent, oxidised or broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch off the ignition and disconnect the 16 track connector from computer component code 1222.
Measure the internal resistance of the computer between the following connections:
●Connection code 151R.
●Connection code 151S
Between components 1222 and 1223.
If the measured value is not 314 ΩΩ Ω Ω

± 10 ΩΩ Ω Ω
or if there is a short circuit on the specified connections, contact Techline.
Switch off the ignition, and disconnect the parking distance control computer to check the insulation, continuity
and the absence of interference resistance on the following connections:
●Connection code 151R,
●Connection code 151S.
Between components 1222 and 1223.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring or replace it.
Measure the resistance value of component 1223 between the following connections:
Measure the resistance between the following connections:
●Connection code 151R,
●Connection code 151S.
Replace the buzzer if its resistance value is not approximately 48 ΩΩ Ω Ω
± 5 ΩΩ Ω Ω
.
If the fault is still present, replace the buzzer.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF006/AAP_V08_DEF006

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 25V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF012
PRESENT
OR
STOREDPARKING DISTANCE CONTROL SWITCH INDICATOR LIGHT
CC.0 : short circuit to earth or open circuit
CC.1 : open circuit or short circuit to +12 volts
NOTESConditions for applying the fault finding procedure to stored faults:
A fault is declared present after reverse gear is engaged and the parking distance
control deactivation switch is pressed.
Check for fuse F42 (10A), check its condition and replace it if necessary.
Remove the parking distance control switch and check the connection and condition of its connector.
Repair if necessary.
Check for earth on connection MAN of the connector of component 1440.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition off, disconnect the parking proximity sensor computer to check the insulation, continuity and
the absence of interference resistance on the following connection:
●Connection code 151E between components 1222 and 1440.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the presence and condition of fuse F6 (15A); replace it if necessary.
Check the + 12 V supply on connection LPDAP3 between components 1440 and 1016.
Check for earth on the connection MG between components 1222 and the earth MG.
If the fault is still present, replace the parking distance control switch.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF012/AAP_V08_DEF012

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 29V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
ET001
REVERSE GEAR ENGAGED
NOTESSpecial note:
Only carry out the checks if the YES and NO statuses are not consistent with the
position of the gear lever.
Check that the reversing lights are working properly: they should come on when reverse gear is engaged and go
out when shifting out of reverse
Check for the presence and condition of fuse F6 (15A); replace it if necessary.
Check for the + 12 V supply on connection AP3 between components 155 and 1016.
If the reversing lights fail to function as specified:
With the ignition switched off, disconnect the parking distance control computer connector to check the
insulation (against + 12 V), the continuity and the absence of interference resistance on the following
connection:
Connection code H66P between components 1222 and 172.
Connection code H66P between components 1222 and 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the reverse gear switch is operating correctly.
If the fault is still present, replace the reverse gear switch.
If the lights come on and the connections are correct, contact the Techline.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ ET001/AAP_V08_ ET001
MR-413-X44-87F000$660_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 30V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08
ET002
BUZZER CONTROL
NOTESThere must be no present or stored faults.
ET002
remains INACTIVE
ET002
ON but buzzer does
not sound
Check that the parking distance control system is activated using status ET003
“Parking distance control” function (parking distance control switch indicator light
off) and check that status ET001 “Reverse gear engaged” shows “YES”.
If the status displays “suspended” or “deactivated”, restart the system by pressing
for 1 or 3 seconds, consult the interpretation of status ET003 “Parking distance
control function”.
Check, when the vehicle is close to an obstacle (between 26 and 150 cm), that the
distance evaluated corresponds to the distance displayed by the diagnostic tool
(PR001 to PR004).
If the distance is inconsistent or if the distance parameters remain at 0 cm, consult
the interpretation of faults DF002 “Left-hand outer sensor”, DF003 “Left-hand
inner sensor”, DF004 “Right-hand outer sensor”, DF005 “Right-hand inner
sensor”.
Check that status ET001 “Reverse gear engaged” is “YES”. Check that the buzzer
volume is not at a zero setting (LC001: ZERO).
If the configured volume is ZERO, reconfigure the computer using command CF001
Buzzer volume. Select the volume setting preferred by the customer (ZERO, MINIMUM,
VERY LOW, LOW, MEDIUM, HIGH, MAXIMUM).
Switch off the ignition, and disconnect the parking distance control computer to check
the insulation and continuity and the absence of interference resistance on the
following connections:
Connection code 151R,
Connection code 151S.
Between components 1222 and 1016.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring or replace it.
Check the condition of the buzzer and that it is operating correctly.
Measure the resistance between the buzzer's two tracks.
Replace the buzzer if its resistance is not approximately 48 ΩΩ Ω Ω
.
If the fault is still present, replace the buzzer.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ ET002/AAP_V08_ ET002

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 31V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08
ET003
PARKING PROXIMITY SENSOR FUNCTION
NOTESSpecial notes:
If the parking proximity sensor system is suspended or deactivated, the parking
proximity sensor switch indicator light comes on.
This status indicates whether the parking distance control system is on or off:
ET003: READY This means that, when reversing, the parking distance control detects
obstacles and the buzzer sounds (the parking distance control switch
indicator light goes out).
ET003: DETECTING This information is displayed when reverse gear is engaged.
This status indicates that the parking distance control system has
detected an obstacle.
ET003: SUSPENDED This means the parking distance control system is switched off
(no detection possible). The suspension is temporary because the
parking distance control system will come back on after the ignition
is switched off and on. Briefly pressing the parking distance control
switch enables the system to be suspended or reactivated manually.
ET003: DEACTIVATED This means the parking distance control system is switched off
(no detection possible). This suspension is permanent (switching
the + after ignition off and on again will not reactivate the system).
Pressing and holding (3 seconds) the parking distance control
switch enables the system to be deactivated or reactivated.
Check the condition of the fuses F6 (15A), F42 (10A), and replace them if necessary.
If the status does not function as described, check the + 12 V supply on connection LPD between components
1440 and 1016. Check for earth on connection MAN of the connector of component 1440.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for a + 12 V supply on connection AP3. Check for an earth on connection MG of the connector of component
1222.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ ET003/AAP_V08_ ET003

PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
87F
87F - 39V2 MR-413-X44-87F000$924_eng.mif
Vdiag No.: 04 08
ALP2 No buzzer
NOTESOnly investigate this customer complaint after a full check using the diagnostic tool
(there must be no present or stored faults).
Using the diagnostic tool Main Data screen, check
that the parking distance control system is on.
The status ET003 Parking proximity sensor
function must be READY (and the red warning light
on the parking proximity sensor switch must be off).
Is status ET003 Parking proximity sensor
"READY"?
YES
Using the diagnostic tool's Main Data screen,
check that reverse gear is selected.
The ET001 Reverse gear selected status must be
YES.
Also ensure that the reversing lights come on when
reverse gear is selected.
Is status ET001 YES?
YES
Using the diagnostic tool configuration readings
screen, check that the buzzer volume has not been
switched off (LC001 Buzzer volume should not be
ZERO).
Is the LC001 function ZERO
NO
NOTurn on the parking proximity sensor by
pressing the switch for 1 or 3 s econds (the
red light should go out).
Note:
For more information concerning the
activation of the system, consult the
interpretation of status ET003 Parking
proximity sensor.
NOApply the interpretation of status ET001
Reverse gear engaged.
YESReconfigure the buzzer volume using the
diagnostic tool (command CF001 Buzzer
volume).
AFTER REPAIRCheck that the system is operating correctly.
AAP_V04_ ALP2/AAP_V08_ ALP2