2009 RENAULT TWINGO engine

80D-38
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 8
CONTINUED 2
Front fog lights relay check:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code 8A between components 231 and 209.
●Connection code BP16 between components 231 and 1016.
●Connection code MAM between components 231 and earth MAM.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connections BP59 and BP11 of component 209. Check for earth on connection MAN
(for right-hand drive vehicles) or MAM (for left-hand drive vehicles) of component 209.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check between the horn and lights switch and the passenger compartment fuse and relay box:
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code BP59 between components 209 and 1016.
●Connection code BP11 between components 209 and 1016.
●Connection code MAN or MAM between components 209 and earth MAN or earth MAM (depending on the
driving layout, right- or left hand drive).
Check between the engine relay/fuse box (component 597) and the Passenger compartment fuse and relay
box (component 1016):
●Connection code BP11 between components 597 and 1016.
●Connection code BP13 between components 597 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the supplies, the earth and the connections are correct, replace the horn and lights switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

80D-39
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 9Lights are not switched off after switching off the + after ignition
feed and the driver's door opening
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" and commands AC054 Dipped headlights and AC055 Side
lights in the UCH.
Note:
For the lights to switch off automatically after driving, the following conditions must all be met:
–engine stopped,
–ignition: 0 (inactive),
–vehicle speed > 0 mph (0 km/h),
–driver's door: closed.
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the operation of status ET142 "Engine
operating phase".
Is the status functioning correctly?
YES
Make sure that status ET239 Ignition switch
position is working.
Is the status functioning correctly?
YES
NOApply the procedure for processing status
ET142.
NOApply the procedure for processing status
ET239.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP9

80D-41
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 10 Lights not switching on at night
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
The engine must be running in order for the automatic lighting function to operate and
the system must be equipped with a rain/light sensor.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" in the UCH. Check that the following faults are not present:
–DF011 "Rain/light sensor circuit",
–DF135 "Rain sensor",
–DF136 "Light sensor".
Deal with the above faults if they are present.
Note:
The sensor requests the lights to be switched on when there is poor light intensity (at night, in a tunnel, etc.).
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Activate the automatic lighting function by switching
the side lights on and off twice in succession:
a beep will sound to confirm this.
Did a beep sound?
YES
NORefer to the interpretation of status ET081
"Lighting stalk position".
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP10

80D-42
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 10
CONTINUED
If the vehicle is fitted with a rain/light sensor, check that the vehicle is configured with a rain/light sensor.
Check that LC044 "Rain/light sensor" displays "Present". If not, carry out CF035 "Rain/light sensor".
Check that LC096 "Automatic wiper function" displays "With". If not, carry out CF194 "Automatic wiper
function".
Check that LC095 "Automatic lighting function", displays "With". If not, carry out CF193 "Automatic
headlight function".
Check that status ET142 Engine operating
phase is RUNNING.
Is status ET142 RUNNING?
YES
Check that the windscreen is clean and in good condition (no cracks, bonded correctly, etc.).
Check that the sensor is present and correctly positioned.
Check that the windscreen is the correct type.
NORun fault finding on the multiplex network and
the injection computer. (see 88B,
Multiplexing and 13B, Diesel injection or
17B, Petrol injection)
AFTER REPAIRCarry out a complete check with the diagnostic tool.