2009 RENAULT TWINGO lights

83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD

Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif

83A-35
MR-413-X44-83A000$616.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of statuses
ET004
SIDE LIGHTS SWITCH
NOTESSpecial notes:
–Only perform these tests if the statuses do not correspond with the system
programming functions.
–Side lights on.
INACTIVE
NOTESIf the status becomes “INACTIVE”, apply the following fault
finding procedure.
Check fuse F43 (10A) of the passenger compartment fuse box, component code 1016.
Check the connection and condition of the connector of component 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the + 12 V supply to connection LPG of component 247.
If the connection is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance of:
Connection LPG between component 1016 and component 247.
Connection MAN35 of component 247.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET004 / TDB_V08_ET004

Vdiag No.: 04, 08
MR-413-X44-83A000$616.mif

83A-40
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET245
INDICATORS
NOTESCheck for the absence of faults on the indicators in the UCH field before starting
fault finding.
Vehicle under + after ignition feed.
If the indicator lights are not displayed or are inconsistent with the position of the control, carry out the following
fault finding procedure.
If status ET245 INDICATORS is INACTIVE and the control is activated:
Check that the connector of component 247 is in good condition and correctly connected.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the connector, otherwise replace the wiring.
Check the continuity of:
Connection 64C between component 645 and component 247 (left-hand indicator)
Connection 64D between component 645 and component 247 (right-hand indicator)
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET245 / TDB_V08_ET245

83A-59
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.Replace the instrument panel,
component code 247 (see
MR 411, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
Record the resistance value provided by the CLIP tool.
Compare the value from the CLIP tool with the warning
resistance, which should be 260 ΩΩ Ω Ω
.
Is this value above or equal to 260 ΩΩ Ω Ω
?Contact the Techline.
Rock the vehicle and check whether the resistance changes by
± 5 ΩΩ Ω Ω
.
Is there a change in the resistance value?Contact the Techline.
NO
YES
YES
NO
YES
NO
A
TDB_V04_ALP5/TDB_V08_ALP5

83A-63
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 6Fault with no warning given by warning light (addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.
Does the fuel warning light illuminate for 3
seconds when + after ignition is switched on?Replace the instrument panel,
component code 247 (see MR 411,
Mechanical, 83A, Instrument panel,
Instrument panel: Removal -
Refitting).
With the ignition off, disconnect the fuel sender
connector, component code 833 and then check the
resistance using a multimeter.
Compare the value measured to the value supplied by
the CLIP tool.
Is the value measured and the value provided by
the CLIP tool the same as or approximately ± 5 ΩΩ Ω Ω
?
Contact the Techline.
NO
YES
NOB
YES
TDB_V04_ALP6/TDB_V08_ALP6