2009 RENAULT TWINGO door lock

82D-17
MR-413-X44-82D000$500_eng.mif
V1
ACCESS/SAFETY
Fault finding - Function82D
d) Automatic locking
Automatic relocking takes place 2 minutes after an unlocking which is not followed by the opening of a door or the
tailgate.
The RAID function locks the vehicle as soon as the speed signal is above approximately 3 mph (5 km/h).
A road test can be used to check whether the RAID function is active or inactive.
The RAID function can be activated or deactivated by pressing and holding the electric door locking switch for
approximately 5 s while the engine is running. Acknowledgement is indicated by a buzzer.
Lock motor operation and feed via the UCH can be checked using the following actuator commands:
–AC004 Central door locking
–AC005 Central door unlocking
–AC061 Unlocking the tailgate
–AC035 Deadlocking
Entry level vehicle access and safety. This function is also divided into another three
sub-functions:
–Access:
This feature is not controlled by the UCH and comprises the following components:
–2 side door mechanical locks.
–1 tailgate electric lock.
–1 tailgate locking switch (with lock barrel).
–1 tailgate switch
Note:
Entry level vehicles are equipped with this system and these vehicles do not have electric central door locking.
–Safety and starting:
Identical to top of the range vehicles.Note:
Unlocking can be performed by the UCH if the airbag computer has detected an impact or if it is faulty (not
recognised on the multiplex network, internal fault, etc.).
(See 88C, Airbag - Seat belt pretensioners).

82D-20
MR-413-X44-82D000$600_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Configurations and programming
Replacing the computer
After the injection computer or UCH has been replaced, program the immobiliser code into the new computer
(see 87B, Passenger compartment connection unit, Configuration and programming).
Access/Safety function configurations in the UCH
–Individual configuration available using the diagnostic tool, and the associated configuration should be read
Procedure to follow for modifying these configurations
–establish dialogue with the computer corresponding to the desired configuration.
–select the "repair mode" menu,
–select the "enter configuration" menu,
–select the line corresponding to the configuration to be modified,
–in the drop-down menu, select the line corresponding to the vehicle equipment level or to the customer selection
and click on "confirm",
–In the "Read configuration" menu, check that the configuration has been completed.
SR.*: Sunroof
*RF: radio frequencyEquipment required
Diagnostic toolClip
ConfigurationConfiguration
readingName of configuration Option
CF009 LC003Deadlocking WITH/WITHOUT
-LC089Memory key function WITH/WITHOUT
CF108 LC040 "Renault Anti-Intruder Device"WITH/WITHOUT
CF009 LC003 "Deadlocking"WITH/WITHOUT
CF192 LC093 "Central door locking"WITH/WITHOUT
CF195 LC097 "Type of key" STANDARD/RF*
CF229 LC126 "Alarm"WITH/WITHOUT
CF031 - "Calibration"-
CF173 LC070 "One-touch window(s)/SR*"WITH/WITHOUT
Note:
If configuration LC089 "Memory key function" is WITH and if status ET407 "Memory key" is YES, the UCH
allows the vehicle information stored in the key to be used.
MR-413-X44-82D000$600_eng.mif

82D-21
MR-413-X44-82D000$700_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Conformity check
SUB-FUNCTION: ACCESS
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET061
(see 87B, UCH).
2ET463:Door(s) or
tailgateOPEN
CLOSEDIn the event of a fault,
apply the
interpretation of
status ET463
(see 87B, UCH).
3
Locking/unlocking
buttonET186:Short press on
door closing
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET186
(see 87B, UCH).
4ET189:Long press on
door opening
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET189
(see 87B, UCH).
5Electric central
locking buttonET044:Central
Locking buttonPRESSED
RELEASEDIn the event of a fault,
refer to the
interpretation of
status ET044
(see 87B, UCH).
6One-touch window/
SR*ET087:One-touch
window/SR*
authorisationPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET087
(see 87B, UCH).
MR-413-X44-82D000$700_eng.mif

82D-22
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: ACCESS (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)7Locking
commandAC004:Central door
lockingThis command is
used to test whether
central door locking is
workingIn the event of a
fault, refer to the
procedure for
command AC004
(see 87B, UCH).
8Deadlocking
controlAC035:DeadlockingThis command is
used to test whether
the deadlocking is
working if the vehicle
is configured "WITH"
deadlocking.In the event of a
fault, refer to the
procedure for
command AC035
(see 87B,
Passenger
compartment
connection unit).
9AC005:Central door
unlockingThis command is
used to test whether
the 4 doors, tailgate
and fuel filler flap
unlocking function is
operating correctly.In the event of a
fault, refer to the
procedure for
command AC005
(see 87B,
Passenger
compartment
connection unit).
10Tailgate opening
controlAC061:Tailgate openingThis command is
used to test whether
the tailgate opening
motor is working.In the event of a
fault, refer to the
procedure for
command AC061
(see 87B,
Passenger
compartment
connection unit).

82D-31
MR-413-X44-82D000$800_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Customer complaints
NOTESOnly consult these customer complaints after a complete check with the
diagnostic tool.
ACCESS82D
FAULT WITH LOCKING AND UNLOCKING WITH
THE RADIOFREQUENCY KEY CONTROLALP 20
TAILGATE OPENING PROBLEM ALP 21
CENTRAL LOCKING/UNLOCKING FAULT ON
ONE OR MORE DOOR(S)ALP 22
RENAULT ANTI-INTRUDER DEVICE
FUNCTION FAULTALP 23
OPENING FROM THE INSIDE NOT POSSIBLE ALP 24
PROTECTION - STARTING82D
STARTING PROTECTION (VEHICLE DOES NOT START
WHEN IGNITION KEY TURNED)ALP 25
MR-413-X44-82D000$800_eng.mif

82D-32
MR-413-X44-82D000$900_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Fault Finding Chart
*RF: radio frequency
*CPE: Electric central door locking
ALP 20 Fault locking and unlocking with the radio frequency key switch
NOTESOnly check this customer complaint after performing a complete check with the diagnostic
tool.
In particular, check the operation of statuses ET186 "Short press on door closing
button", ET189 "Short press on door opening button", ET045 "RF* signal received",
ET181 "Key allocated to vehicle", ET240 "Key frequency (in MHz), ET044 "CPE*
button", ET463 "Door(s) or tailgate" and commands AC004 "Central door locking"
and AC005 "Central door unlocking".
Check the following conformities:
CF009 "Deadlocking" with LC003 "Deadlocking" (depending on equipment).
CF108 "Renault Anti-Intruder Device" with LC040 "Renault Anti-Intruder Device".
CF192 Central door locking with LC093 Central door locking.
CF195 "Type of key" with LC097 "Type of key" is "Standard".
Check the correct operation of status ET463 "Door(s) or tailgate".
Check that all doors are correctly closed.
Check that + after ignition feed is not present.
Press the button to check that status ET193 "RF*
signal of key allocated to vehicle" changes to
"Present".
NO
YES
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP20
MR-413-X44-82D000$900_eng.mif

82D-33
MR-413-X44-82D000$900_eng.mif
V1
ACCESS/SAFETY
Fault finding - Fault Finding Chart82D
ALP 20
CONTINUED
Carry out a locking/unlocking request with a different
key belonging to the same vehicle.
Did the switch work?
NO
With the + after ignition switched on, carry out a
locking/unlocking request on the vehicle via the
electric door locking switch.
Did the switch work?
NO
Check the wiring between the door locks and
the UCH. Carry out the necessary repairs.
YESCheck the charge of the key battery
Check the condition of the first key and its
contacts.
Replace the battery or the key if necessary.
YESUse the diagnostic tool to check the statuses
associated with pressing the buttons on the
key.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

82D-34
MR-413-X44-82D000$900_eng.mif
V1
ACCESS/SAFETY
Fault finding - Fault Finding Chart82D
Vehicle which is equipped with deadlocking function:
ALP 21 Tailgate opening fault
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
In particular, check the operation of statuses ET463 "Door(s) or tailgate", ET157
"Tailgate opening request" and command AC061 "Tailgate opening".
Check the following conformities:
CF009 Deadlocking with LC003 Deadlocking.
CF108 "Renault Anti-Intruder Device" with LC040 "Renault Anti-Intruder
Device".
CF192 Central door locking with LC093 Central door locking.
Check that DF133 "Deadlocking motor(s) circuit"is not present.
The vehicle and the tailgate must be unlocked.
If the tailgate is already open, the tailgate opening
function is disabled.
Check the wiring between the tailgate lock and
the UCH.
Carry out the necessary repairs.
Remove the lock, close the lock by sliding a
screwdriver into it; test the lock by connecting an
earth and a +battery feed to the motor terminals
(for less than one second).
If the lock still does not work, replace the lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP21