2009 RENAULT SCENIC coolant temperature

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 168V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER (continued 2)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
8Cruise control/
speed limiter
deactivationET415:Cruise control/speed
limiter
deactivationNONE: This status is
present on the diagnostic
tool when:
The computer has been
reinitialised.
The computer has been
reprogrammed.
- STATUS 1: Traction
control request
- STATUS 2: Brake pedal
depressed.
- STATUS 3: Clutch pedal
depressed.
- STATUS 4: Cancel
button pressed
- STATUS 5: Cruise
control or speed limiter
monitoring.
- STATUS 6: Gear lever
in neutral (manual
gearbox) or neutral
position (automatic
transmission).
- STATUS 7:
Inconsistency between
the request and the
vehicle speed.
- STATUS 8: Automatic
transmission in defect
mode.
- STATUS 9: Vehicle
speed monitoring.
- STATUS 10: Monitoring
by injection computer.In the event of a fault,
consult the
interpretation of status
ET415 Cruise control/
speed limiter
deactivation.

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 169V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
STARTING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Power supplyET001:Computer + after
ignition feedPRESENTIn the event of a fault,
carry out a full fault finding
procedure on the charging
circuit.
2StartingET238:SynchronisationDONEIn the event of a fault, refer
to fault interpretation
DF195 Camshaft/engine
speed sensor
consistency.
ET076:StartingAUTHORISEDIf status ET076 is
PROHIBITED, carry out a
complete fault finding
procedure on the
multiplex network.
3Engine
operation.ET038:EngineRUNNINGNone
4Power supplyPR071:Computer feed
voltage9 V < voltage < 16 VIn the event of a fault,
consult the interpretation
of fault DF047 Computer
supply voltage.
PR358:Sensor reference
voltage3.4 V < voltage < 3.8 VNone

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 170V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
PROTECTION
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Engine
immobiliserET341:Immobiliser code
programmedYESIf status ET341 is locked
on NO (see 87B,
Passenger
compartment
connection unit).
ET003:Engine
immobiliserINACTIVEIf status ET003 is locked
on ACTIVE (see 87B,
Passenger
compartment
connection unit).
2Vehicle impactET077:Impact detectedNOIn the event of a fault, refer
to the interpretation of
fault DF069 Impact
detected signal.
3StartingET076:StartingAUTHORISED:
injection authorises
startingIf status ET076 is
PROHIBITED (see 87B,
Passenger
compartment
connection unit).

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 176V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET014
CHECK COOLING FAN 1
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOTE:
Status ET014 test and status ET022 GMV1 low speed request change their status at the same time.
RUNNING
The low-speed engine fan unit is supplied in three scenarios:
–the engine coolant temperature is above 89 ˚C;
–the air conditioning is operating
–the injection computer has system faults that could lead to the engine overheating.
When the low-speed engine fan is supplied:
–status ET014 GMV 1 test becomes RUNNING status ET022 Low speed GMV
request becomes ACTIVE.
If the low speed GMV does not work (see 87G, engine compartment connection unit).
The low-speed engine fan assembly stops when:
–the engine coolant temperature is below 89 ˚C;
–the air conditioning is not switched on by the driver.
STOPPED
IMPORTANTWARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is faulty, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET014

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 177V3 MR-372-J84-13B250$630.mif
STOPPED
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET015
CHECK COOLING FAN 2
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOTE:
Status ET015 GMV 2 test and status ET021 High speed GMV request change their status at the same time.
RUNNING
The engine fan assembly can be supplied when:
–the engine coolant temperature is above 99 ˚C.
–the injection computer has system faults that could lead to the engine overheating.
When the high speed fan is supplied:
–status ET015 GMV 2 test becomes RUNNING and status ET021 High speed GMV
request becomes ACTIVE.
The high-speed engine fan assembly stops when:
–the engine coolant temperature is below 99 ˚C;
IMPORTANTWARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is faulty, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET015

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 178V3 MR-372-J84-13B250$630.mif
INACTIVE
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET021
HIGH-SPEED FAN REQUEST
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOTE:
Status ET021 High speed GMV request and status ET015 GMV 2 test change their status at the same time.
ACTIVE
The injection computer requests the activation of the high speed GMV when:
–the engine coolant temperature is above 99 ˚C.
–the injection computer has system faults that could lead to the engine overheating.
When the high speed fan is supplied:
–status ET021 High speed GMV request becomes RUNNING and status ET015
GMV 2 test becomes ACTIVE.
The high-speed engine fan assembly stops when:
–the engine coolant temperature is below 99 ˚C;
–no fault which could cause engine overheating is present in the injection
system.
IMPORTANTWARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is faulty, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET021

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 179V3 MR-372-J84-13B250$630.mif
INACTIVE
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET022
LOW SPEED GMV CONTROL
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOTE:
Status ET022 Low speed GMV request and status ET014 GMV 1 test change their status at the same time.
ACTIVE
The injection computer requests the activation of the low speed GMV when:
–the engine coolant temperature is above 89 ˚C;
–the injection computer has system faults that could lead to the engine overheating,
–the air conditioning is switched on by the driver.
When the high speed fan is supplied:
–status ET022 Low speed GMV request becomes ACTIVE and status ET014 GMV
1 test becomes RUNNING.
The low-speed engine fan assembly stops when:
–the engine coolant temperature is below 89 ˚C;
–no fault which could cause engine overheating is present in the injection
system.
–the air conditioning is not switched on by the driver.
IMPORTANTWARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is faulty, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET022

DIESEL INJECTION
Fault finding – Parameter summary table13B
13B - 206V3 MR-372-J84-13B250$675.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51DIESEL INJECTION
Fault finding – Parameter summary table
OCR*: opening cyclic ratioTool parameter Diagnostic tool title
PR005EGR valve opening setpoint
PR006Rail pressure regulator current
PR007Rail pressure regulator current setpoint
PR008Rail pressure setpoint
PR009Turbocharging pressure setpoint
PR011Turbocharging solenoid valve position correction
PR015Engine torque
PR016Alternator flow
PR017Fuel flow
PR022EGR valve position feedback loop difference
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure
PR038Rail pressure
PR041Turbocharging pressure
PR047Turbocharging pressure OCR*
PR048OCR* rail pressure regulation valve
PR051EGR valve position feedback
PR053Speed requested by air conditioning
PR055Engine speed
PR059Inlet air temperature
PR061Exterior air temperature
PR064Coolant temperature
PR071Computer feed voltage
PR073Air flowmeter feed voltage
PR076Refrigerant sensor voltage
PR077EGR valve position sensor voltage
MR-372-J84-13B250$675.mif