2009 PORSCHE 911 brake pads

4Sport tiresSport tires (ultra high performance tires) are ap-
proved for use on public highways and comply
with all statutory requirements and safety criteria.
The design of the tire is also geared towards use
on racing circuits (driver safety training courses,
sports driving schools, Club Sport events) and
provides distinct advantages here in terms of dry
grip and wear compared to conventional road
tires.
The major features are a reduced tread depth and
a special tread pattern and carcass.
The design features of this sports tire result
in the following effects compared with other
summer tires when used under normal
driving conditions:
– Sport tires have a smaller tread depth, and
thus can reach their wear limit sooner.
As with all tires, the attainable mileage de-
pends on the individual driving style and the
conditions of use.
– Exercise caution when driving on wet roads,
paying special attention to hydroplaning situa-
tions (stagnant water, puddles, lane grooves).
Sport tires have a lower tread depth than nor-
mal tires and you must therefore adapt speed
accordingly when driving on wet surfaces.– The driver’s skill level must be commensurate
with the vehicle performance levels in the up-
per range limits, due to increased safety risks
in the upper range limits.
fAt oudside temperatures below 45 °F (7 °C)
change to snow tires.
fNotify anyone using your car of these charac-
teristics and possible effects.
Danger!
Risk of accident through loss of road surface
contact, control over the vehicle and braking
ability, leading to serious personal injury or
death.
The reduced tire tread depth means that
there is an increased risk of aquaplaning on
wet roads.
fWhen driving on wet or mud-covered roads re-duce speed significantly. Danger!
Risk of accident from worn tires.
Sport tires have a smaller tread depth, and
thus can reach their wear limit sooner.
It is important to check tire wear frequently
to avoid risk of serious personal injury or
death from worn tires.
fCheck tire wear frequently.
Porsche Ceramic Composite Brake
(PCCB)fPlease see the chapter “BRAKES” on Page 58.
The high-performance brake system is designed
for optimal braking effect at all speeds and
temperatures.
Certain speeds, braking forces and ambient
conditions (such as temperature and humidity)
therefore might cause brake noises.
Wear on the different components and braking
system, such as brake pads and brake discs,
depends to a great extent on the individual driving
style and the conditions of use and therefore
cannot be expressed in actual miles on the road.
The values communicated by Porsche are based
on normal operation adapted to traffic. Wear
increases considerably when the vehicle is driven
on race tracks or through an aggressive driving
style.
fPlease consult an authorized Porsche dealer
about the current guidelines in effect before
such use of your vehicle.

10
Before driving off...
Break in hints for the first
2,000 miles/3,000 kilometers The following tips will be helpful in obtaining opti-
mum performance from your new Porsche.
Despite the most modern, high-precision manufac-
turing methods, the moving parts must still wear
in with each other. This wearing-in occurs mainly in
the first 2,000 miles/3,000 kilometers.Therefore: fPreferably take longer trips.
fAvoid frequent cold starts with short-distance
driving whenever possible.
fAvoid full throttle starts and abrupt stops.
fDo not exceed maximum engine speed of
4,200 rpm (revolutions per minute).
fDo not run a cold engine at high rpm either in
Neutral or in gear.
fDo not let the engine labor, especially when
driving uphill. Shift to the next lower gear in
time (use the most favorable rpm range).
fNever lug the engine in high gear at low
speeds. This rule applies at all times, not just
during the break-in period.fDo not participate in motor racing events,
sports driving schools, etc. during the first
2,000 miles/3,000 kilometers.
There may be a slight stiffness in the steering,
gear-shifting or other controls during the break-in
period which will gradually disappear.
Break in brake pads and brake discsNew brake pads and discs have to be “broken in”,
and therefore only attain optimal friction when the
car has covered several hundred miles or km.
The slightly reduced braking ability must be com-
pensated for by pressing the brake pedal harder.
This also applies whenever the brake pads and
brake discs are replaced. New tires New tires do not have maximum traction. They
tend to be slippery.
fBreak in new tires by driving at moderate
speeds during the first 60 to 120 miles/100 to
200 km. Longer braking distances must be an-
ticipated.
Engine oil and fuel consumption During the break-in period oil and fuel consump-
tion may be higher than normal.
As always, the rate of oil consumption depends on
the quality and viscosity of oil, the speed at which
the engine is operated, the climate and road con-
ditions, as well as the amount of dilution and oxi-
dation of the lubricant.
fMake a habit of checking engine oil with every
refueling, add if necessary.

60
Operation, Safety
Brake booster The brake booster assists braking only when
the engine is running.
When the car is moving while the engine is not run-
ning, or if the brake booster is defective, more
pressure on the brake pedal is required to bring
the car to a stop.
If this happens, ABS and PSM will also not oper-
ate.
Moisture or road salt on brakes affects braking.
When the vehicle is driven on salted or sanded
roads for extended periods, the brakes should be
washed down thoroughly about every 2 weeks. An
automatic carwash facility cannot do this job prop-
erly.
Brakes will dry after a few cautious brake applica-
tions.
Warning!
Risk of an accident, resulting in serious per-
sonal injury or death.
Driving through water may reduce the trac-
tion.
Moisture on brakes from road water, car
wash, or coating of road salt may affect
braking efficiency.
fCautiously apply brakes to test brakes after ex-posure to road water, etc.
Brake wear Your car has excellent brakes, but they are still
subject to wear. The rate at which they wear de-
pends on how the brakes are used.
fHave the brake system inspected at the
intervals recommended in your Maintenance
Booklet.
Brake system warning light
You can check the functionality of the brake
system warning light by switching the ignition to
the "On" position and verifying that the warning
light illuminates.
If the warning lights in the instrument panel and on-
board computer stay on when the engine is run-
ning or come on while driving, the brake pads are
worn excessively.
fDo not continue to operate the vehicle.
Have your authorized Porsche dealer inspect
or replace the brake pads.
Brake pads Wear on the brake pads and brake discs depends
to a great extent on the driving style and the con-
ditions of use and therefore cannot be expressed
in actual miles on the road.
The high-performance brake system is designed
for optimal braking effect at all speeds and tem-
peratures.
Certain speeds, braking forces and ambient
conditions (such as temperature and humidity)
therefore might cause “brake noises”.
New brake pads or linings
New brake pads and brake discs have to be “bro-
ken in”, and therefore only attain optimal friction
when the car has covered several hundred miles
or km.
The slightly reduced braking ability must be com-
pensated for by pressing the brake pedal harder.
This also applies whenever the brake pads and
brake discs are replaced.
Warning light USA
Warning light Canada

66
Operation, Safety
Porsche Stability Management
(PSM)PSM is an active control system for stabilization of
the vehicle approaching the performance limits of
driving maneuvers.
Warning!
Risk of an accident, resulting in serious per-
sonal injury or death.
The increased control that is provided should
not induce you to take greater risks with your
safety. The limits dictated by the laws of
physics cannot be overcome, even with PSM.
The risk of accidents due to inappropriate
speed cannot be reduced, even by PSM.
The driver bears the responsibility for all
driving maneuvers.
fAdapt your driving style to the prevailing road
and weather conditions.
fObey all traffic laws.
Sensors at the wheels, brakes, steering system
and engine continuously measure:
–Speed
– Direction of travel (steering angle)
– Lateral acceleration
– Rate of turn about the vertical axis
– Longitudinal accelerationPSM uses these values to determine the direction
of travel indicated by the driver.
PSM intervenes and helps to correct the course if
the actual direction of motion deviates from the
chosen course (steering-wheel position):
It brakes individual wheels as needed. In addition,
the engine power may be manipulated in order to
stabilize the vehicle.
The events below inform the driver of PSM control
operations and warn him/her to adapt his/her
driving style to the road conditions:
– The multifunctional information light on the
instrument panel flashes.
– Hydraulic noises can be heard.
– The vehicle decelerates and steering-wheel
forces are altered as the PSM controls the
brakes.
– Reduced engine power.
– The brake pedal pulsates and its position is
changed during braking.
In order to achieve full vehicle deceleration,
foot pressure must be increased after the
brake pedal has begun vibrating.
Examples of PSM control operations– If the front wheels of the vehicle drift on a
bend, the rear wheel on the inside of the bend
is braked and the engine power is reduced if
necessary.
– If the rear of the vehicle swings out on a bend,
the front wheel on the outside of the bend is
braked.Additional braking functions– Pre-filling the brake system:
The brake system is prepared for possible
subsequent emergency braking if the acceler-
ator pedal is released suddenly and quickly.
The brake system is prefilled and the brake
pads are already applied gently to the brake
discs.
– Brake booster:
In the event of an emergency braking operation
where the pedal force is insufficient, a brake
booster provides the braking pressure neces-
sary for maximum deceleration at all 4 wheels.Advantages of PSM– Best possible traction and lane-holding ability
in all driving situations – even on road surfaces
with varying friction.

Instruments, On-Board Computer, Warnings
125
Check Engine
(Emission Control)The emission control system detects malfunctions
early that could, for example, cause increased
pollutant emissions or consequential damage.
Faults are indicated by a continuously lit or
flashing instrument panel warning light.
The faults are recorded in the control unit's fault
memory.
The warning light in the instrument panel lights up
when the ignition is switched on as a bulb check
and goes out approx. 4 seconds after the engine
starts. If the warning light does not light up, have
the bulb replaced promptly.
The warning light in the instrument panel flashes to
indicate operating states (e.g. engine misfiring)
which might cause damage to certain parts of the
emission control system.
fIn this case, immediately reduce the engine
load by easing off the accelerator.
fIn order to avoid consequential damage to the
engine or emission control system (e.g. cata-
lytic converter), have the fault diagnosed and
rectified immediately at the nearest authorized
Porsche dealer.If the warning light in the instrument panel lights up
permanently without flashing before and remains
on while driving, it suggests:
– a potential engine control problem and the
need for system service or
– an improperly fastened tank cap or
– the vehicle was refueled while the engine was
running.
fStop immediately at a suitable and secure
place and check tank cap for proper fastening.
If tank cap was fastened correctly, see your au-
thorized Porsche dealer for service as soon as
possible.
Caution!
If the check engine warning light in the in-
strument panel is flashing, serious catalytic
converter damage and power loss will soon
occur.
Prolonged driving with the check engine war-
ning light on could cause damage to the
emission control system. It also could affect
fuel economy and driveability.
fHave the fault remedied at the nearest authorized Porsche dealer immediately.The central warning light on the instrument panel
lights up if there are warning messages in the
INFO menu.
The messages can be called in the on-board
computer INFO menu:
fPlease see the chapter “INFO WARNING MES-
SAGES” on Page 132.
The warning light on the instrument panel lights
up:
– if the handbrake is on,
– if the brake fluid level is low,
– if the brake pads have reached the wear limit,
– if the brake circuit division is defective.
Additionally, a warning is displayed by the on-
board computer.
fPlease see the chapter “WARNINGS ON THE
INSTRUMENT PANEL AND THE ON-BOARD
COMPUTER” on Page 158.
Warning Light
Central Warning Light
Brake Warning Light USA
Brake Warning Light Canada

Warnings
161
Warning Battery/generator Stop at a safe place and switch the engine off.
Do not continue driving.
Have the fault remedied at an authorized
Porsche dealer.
Oil pressure gage faulty Have the fault remedied at an authorized
Porsche dealer.
Oil level display faulty Have the fault remedied at an authorized
Porsche dealer.
Oil temperature gage faulty Have the fault remedied at an authorized
Porsche dealer.
Oil temperature
too highSwitch engine off and let it cool. Check oil level
and, if necessary, add oil.
Please observe the chapter “OIL DISPLAY AND
MEASUREMENT OF THE ENGINE OIL LEVEL“.
Indicator faulty Coolant indicator failed.
Have the fault remedied at an authorized
Porsche dealer.
Brake pad wear Have the brake pads changed immediately at an
authorized Porsche dealer.
Warning – Brake fluid level Stop immediately in a suitable place.
Do not continue driving. Have the fault remedied
at an authorized Porsche dealer.
Warning – Brake circuit division Stop immediately in a suitable place.
Do not continue driving. Have the fault remedied
at an authorized Porsche dealer.
Instrument
panelOn-board
computerText display on on-board
computerMeaning/measure

Index
301
AABS (antilock brake system) .......................... 61
Warning light ........................................ 62
Adaptive sports seat..................................... 31
Adjusting Headlights.................................... 278
Advanced Airbag........................................... 45
Air conditioning compressor ................ 106, 108
Air conditioning system ............................... 106
Air distribution .................................... 106, 108
Air filter ...................................................... 222
Air intake.................................................... 109
Airbag
Advanced ............................................. 45
Cleaning covers .................................. 230
Deactivation device............................... 49
Function ............................................... 45
Maintenance ......................................... 48
Warning light .................................. 48, 56
Airbag Systems ............................................ 44
Alarm system ....................................... 23, 100
Deactivating passenger compartment
monitoring ............................................ 24
Fault indication...................................... 24
Function indication................................ 23
Not active .......................................... 258
Alcantara, cleaning ..................................... 231
Antenna ............................................. 100, 225
Antifreeze .................................................. 207
Antifreeze in coolant................................... 207
Antilock brake system (ABS) .......................... 61
Warning light ........................................ 62
Ashtray ........................................................ 89
Assembly aids for wheel changes................. 249
Audio operation ...................................... 98, 99Auto-button, air conditioning.........................106
Automatic
Air conditioning system........................106
Anti-glare mirrors ..................................28
Car washes ........................................225
Door locking ...................................18, 22
Garage door .........................................78
Headlight adjustment.............................81
Speed control .........................86, 87, 116
Transmission ......................................170
Automatic locking retractor............................53
Automatic speed control..............................116
Indicator light ......................................116
Average consumption ..........................127, 157
Average speed ...................................127, 157BBackrest
Adjustment ...........................................30
Release ................................................30
Battery .......................................................261
Care...................................................262
Charge state.......................................261
Charging ............................................262
Putting vehicle into operation ...............263
Remote control ...................................266
Removing ...........................................264
Replacing ...........................................263
Warning light.......................................124
Winter operation..................................263
Before driving off ........................................ 8, 9
Belts ............................................................41
Cleaning .............................................231
Height adjustment .................................43Tensioner ............................................ 41
Warning light ........................................ 42
Blower adjustment...................................... 109
Blower speed adjustment............................ 107
Brake
Break in ............................................... 10
Pads ................................................... 60
Pedal................................................... 59
Wear ................................................... 60
Brake fluid
Changing ........................................... 213
Checking level .................................... 212
Level ................................................. 212
Warning light ...................................... 213
Brake light ................................................. 277
Brake light, additional ................................. 277
Brakes ...................................................... 212
Brake circuit division warning light ....... 213
Brake warning light............................. 125
Fluid .......................................... 212, 290
Fluid warning light............................... 213
Function .............................................. 58
New brake pads or linings ..................... 60
Pads ................................................... 10
Parking brake....................................... 57
Porsche Ceramic Composite Brake
(PCCB) .................................................. 4
Roller brake tester................................ 63
Test stand ........................................... 68
Break in brakes ............................................ 10
Break in hints ............................................... 10
Bulbs, replacing ......................................... 269