2009 PONTIAC VIBE manual transmission

The main components of the
instrument panel are the following:
A.Outside Power Mirror(s) on
page 2-14.
B.Outlet Adjustment on page 7-3.
C.Turn Signal/Multifunction
Lever on page 4-4.
D.Instrument Panel Cluster on
page 4-12.
E.Windshield Wipers on page 4-7.
F. Passenger Airbag Status
Indicator.Passenger Sensing
System on page 1-28.
Security Light. SeeContent
Theft-Deterrent on page 2-10.
G.Hazard Warning Flashers on
page 4-3.
H.Audio System(s) on page 6-1.
I.Traction Control System (TCS)
on page 8-21.
J.Content Theft-Deterrent on
page 2-10.
K.Driver Storage Compartment
on page 3-3.
L.Hood Release on page 9-5.M.Audio Steering Wheel Controls
on page 6-13.
N.Tilt Wheel on page 4-4.
O.Horn on page 4-3.
P.Cruise Control on page 4-4
(If Equipped).
Q.Ignition Positions on page 8-2.
R. Tire Pressure Reset Button
(Out of View). SeeTire Pressure
Monitor Operation on page 9-50.
S.Power Outlet 115 Volt Alternating
Current on page 4-10On/Off
Button.
T. Cigarette Lighter (If Equipped)
or Accessory Power Outlet.
Ashtray(s) on page 4-10
orAccessory Power Outlet(s)
on page 4-9.
U. Shift Lever.Automatic
Transmission Operation
(Four Speed) on page 8-6or
Automatic Transmission
Operation (Five Speed)
on page 8-8orManual
Transmission Operation
on page 8-11.V.Power Outlet 115 Volt Alternating
Current on page 4-10.
W.Climate Control System on
page 7-1.
X.Hooks on page 3-3
.
Y.Glove Box on page 3-1.
Hazard Warning Flashers
|
(Hazard Warning Flasher):
Press this button located on
the instrument panel, to make the
front and rear turn signal lamps ash
on and off. This warns others that
you are having trouble.
Press
|again to turn the
ashers off.
Horn
Press near or on the horn symbols
on the steering wheel pad to
sound the horn.
Instruments and Controls 4-3
2009 - Pontiac Vibe Owner Manual

Increasing Speed While Using
Cruise Control
There are three ways to increase
the vehicle speed:
Use the accelerator pedal to get
to the higher speed. Move the
lever down to−SET. Release the
lever and the accelerator pedal.
Move the cruise lever up
to +RES. Hold it there until the
desired speed is reached,
and then release the lever.
To increase the vehicle speed in
very small amounts, move the
lever to +RES briey and then
release it. Each time this is done,
the vehicle goes about 1 mph
(1.6 km/h) faster.Reducing Speed While Using
Cruise Control
There are two ways to reduce the
vehicle speed while using cruise
control:
Push and hold the lever to−SET
until the desired lower speed is
reached, then release it.
To slow down in very small
amounts, push the lever
down briey. Each time this
is done, the vehicle will go about
1 mph (1.6 km/h) slower.
Passing Another Vehicle While
Using Cruise Control
Use the accelerator pedal to
increase the vehicle speed.
When you take your foot off the
pedal, the vehicle slows down to
the cruise control speed set earlier.
Using Cruise Control on Hills
The cruise control performance will
vary depending upon the vehicle
speed, load, and the steepness of
the hills.When going up steep hills, you might
have to step on the accelerator pedal
to maintain the vehicle speed.
When going downhill, you might
have to brake or shift to a lower gear
to keep the vehicle speed down.
Applying the brake or downshifting
to 2 SECOND or L LOW turns
off the cruise control.
Ending Cruise Control
There are several ways to turn off
the cruise control:
Step on the brake pedal or push
the clutch pedal, if the vehicle
has a manual transmission.
Press the ON-OFF button.
Pull the cruise control lever
toward you.
Erasing Speed Memory
The cruise control set speed memory
is erased when the cruise control or
the ignition is turned off.
4-6 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It makes sure
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.
This light comes on when the ignition
is on, but the engine is not running,
as a check to show it is working. If it
does not, have the vehicle serviced
by your dealer/retailer.If the check engine light comes on
and stays on, when the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Heeding the light can
prevent more serious damage to the
vehicle. This system assists the
service technician in correctly
diagnosing any malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
the vehicle’s fuel economy
might not be as good, and
the engine might not run as
smoothly. This could lead
to costly repairs that might
not be covered by the vehicle
warranty.Notice:Modications made
to the engine, transmission,
exhaust, intake, or fuel system of
the vehicle or the replacement
of the original tires with other
than those of the same Tire
Performance Criteria (TPC) can
affect the vehicle’s emission
controls and can cause this light
to come on. Modications to
these systems could lead
to costly repairs not covered
by the vehicle warranty. This
could also result in a failure
to pass a required Emission
Inspection/Maintenance test.
SeeAccessories and
Modifications on page 9-3.
United States
Canada
4-20 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

Driving and
Operating
Starting and Operating
Your Vehicle
New Vehicle Break-In.........8-2
Ignition Positions................8-2
Retained Accessory
Power (RAP).....................8-4
Starting the Engine.............8-4
Engine Coolant Heater.......8-5
Automatic Transmission
Operation (Four Speed). . . .8-6
Automatic Transmission
Operation (Five Speed).....8-8
Manual Transmission
Operation........................8-11
Parking Brake...................8-12
Shifting Into Park..............8-13
Shifting Out of Park..........8-14
Parking the Vehicle
(Manual Transmission). . . .8-15
Parking Over Things
That Burn........................8-16
Engine Exhaust.................8-16
Running the Vehicle
While Parked..................8-17
Driving Your Vehicle
Defensive Driving..............8-17
Drunk Driving....................8-18
Control of a Vehicle..........8-18
Braking.............................8-19
Antilock Brake
System (ABS).................8-20
Traction Control
System (TCS).................8-21
All-Wheel Drive (AWD)
System............................8-22
StabiliTrak®System..........8-22
Steering............................8-23
Off-Road Recovery............8-24
Passing.............................8-25
Loss of Control.................8-25
Driving at Night.................8-26
Driving in Rain and on
Wet Roads......................8-27
Before Leaving on a
Long Trip........................8-28
Highway Hypnosis.............8-28
Hill and Mountain Roads. . .8-28
Winter Driving...................8-29
If Your Vehicle is Stuck in
Sand, Mud, Ice, or Snow. . .8-31
Rocking Your Vehicle to
Get It Out.......................8-31
Loading the Vehicle..........8-32
Fuel
Fuel..................................8-36
Gasoline Octane...............8-36
Gasoline Specications.....8-36
California Fuel..................8-36
Additives...........................8-37
Fuels in Foreign
Countries........................8-37
Filling the Tank.................8-38
Filling a Portable Fuel
Container........................8-40
Driving and Operating 8-1
2009 - Pontiac Vibe Owner Manual

LOCK/OFF:This is the only position
from which you can remove the key.
This locks the steering wheel,
ignition and automatic transmission.
Push in the ignition switch as you
turn the key toward you.
On vehicles with an automatic
transmission, the shift lever must be
in P (Park) to turn the ignition switch
to the LOCK/OFF position.
A warning tone will sound if the driver
door is opened with the key in the
ignition.
The ignition switch can bind in the
LOCK/OFF position with your wheels
turned off center. If this happens,
move the steering wheel from right
to left while turning the key to
ACC/ACCESSORY. If this doesn’t
work, then the vehicle needs service.{CAUTION
On manual transmission vehicles,
turning the key to LOCK/OFF and
removing it will lock the steering
column and result in a loss of
ability to steer the vehicle.
This could cause a collision.
If you need to turn the engine
off while the vehicle is moving,
turn the key only to ACC/
ACCESSORY. Do not push the
key in while the vehicle is moving.
ACC/ACCESSORY:This position
provides power to some of the
electrical accessories. It unlocks the
steering wheel and ignition. To move
the key from ACC/ACCESSORY to
LOCK/OFF, push in the key and then
turn it to LOCK/OFF.
A warning tone will sound when
the driver door is opened when the
ignition is still in ACC/ACCESSORY
or LOCK/OFF and the key is in the
ignition.ON/RUN:The ignition switch stays
in this position when the engine is
running. This position can be used to
operate the electrical accessories,
including the ventilation fan and
115 volt power outlet, as well as to
display some warning and indicator
lights. The transmission is also
unlocked in this position on
automatic transmission vehicles.
The battery could be drained
if you leave the key in the ACC/
ACCESSORY or ON/RUN position
with the engine off. You may not be
able to start the vehicle if the battery
is allowed to drain for an extended
period of time.
START:This position starts the
engine. When the engine starts,
release the key. The ignition switch
will return to ON/RUN for normal
driving.
Driving and Operating 8-3
2009 - Pontiac Vibe Owner Manual

Retained Accessory
Power (RAP)
These vehicle accessories may be
used for less than a minute after
the engine is turned off.
Power Windows, if equipped
Sunroof, if equipped
The power windows and sunroof
will continue to work for less than a
minute or until either front door is
opened. The radio will work when
the key is in ON/RUN or ACC/
ACCESSORY.
Starting the Engine
Automatic Transmission
Move the shift lever to P (Park) or
N (Neutral). The engine will not start
in any other position. To restart
when you are already moving,
use N (Neutral) only.
Notice:Shifting into P (Park)
with the vehicle moving could
damage the transmission.
Shift into P (Park) only when
your vehicle is stopped.
Manual Transmission
The shift lever should be in
NEUTRAL and the parking brake
engaged. Hold the clutch pedal
to the oor and start the engine.
The vehicle will not start if the clutch
pedal is not all the way down.
Starting Procedure
1. With your foot off the accelerator
pedal, turn the ignition to START.
When the engine starts, let go of
the key. The idle speed will go
down as the engine gets warm.
Vehicles equipped with
the 1.8L engine have a
Computer-Controlled Cranking
System. This feature assists in
starting the engine and protects
components. If the ignition key is
turned to the START position,
and then released when the
engine begins cranking, the
engine will continue cranking for
a about 30 seconds or until the
vehicle starts. If the engine doesnot start and the key is held in
START for many seconds,
cranking will be stopped after
25 seconds to prevent cranking
motor damage. To prevent gear
damage, this system also
prevents cranking if the engine is
already running. Engine cranking
can be stopped by turning
the ignition switch to ACC/
ACCESSORY or LOCK/OFF.
Vehicles equipped with the
2.4L engine should not be
cranked for more than
30 seconds at a time.
This may overheat the
starter and wiring systems.
Notice:Holding the key in
START for longer than 15 seconds
at a time will cause the battery to
be drained much sooner. And
the excessive heat can damage
the starter motor. Wait about
15 seconds between each try to
help avoid draining the battery
or damaging the starter.
8-4 Driving and Operating
2009 - Pontiac Vibe Owner Manual

4. Before starting the engine, be
sure to unplug and store the
cord as it was before to keep
it away from moving engine
parts. If you do not, it could
be damaged.
The length of time the heater should
remain plugged in depends on
several factors. Ask a dealer/retailer
in the area where you will be parking
the vehicle for the best advice
on this.Automatic Transmission
Operation (Four Speed)
The shift lever is located on the
console between the seats.
P (Park):This position locks the
front wheels. It is the best position
to use when you start the engine
because the vehicle cannot
move easily.
{CAUTION
It is dangerous to get out of the
vehicle if the shift lever is not fully
in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the
engine is running unless you have
to. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, always set the
parking brake and move the shift
lever to P (Park). SeeShifting Into
Park on page 8-13. If you are
pulling a trailer, seeTowing a
Trailer on page 9-77.
Make sure the shift lever is
fully in P (Park) before starting
the engine. The vehicle has
an automatic transmission
shift lock control system.
8-6 Driving and Operating
2009 - Pontiac Vibe Owner Manual

You must fully apply the regular
brake rst and move the shift lever to
the right before you can shift from
P (Park) when the ignition key is in
ON/RUN. If you cannot shift out of
P (Park), ease pressure on the shift
lever, then push the shift lever all the
way into P (Park) as you maintain
brake application. Then move the
shift lever to the right and move the
shift lever into another gear. See
Shifting Out of Park on page 8-14.
R (Reverse):Use this gear to
back up.
Notice:Shifting to R (Reverse)
while the vehicle is moving
forward could damage the
transmission. The repairs would
not be covered by the vehicle
warranty. Shift to R (Reverse)
only after the vehicle is stopped.
To rock the vehicle back and
forth to get out of snow, ice or sand
without damaging the transmission,
seeIf Your Vehicle is Stuck in
Sand, Mud, Ice, or Snow on
page 8-31.N (Neutral):In this position, the
engine does not connect with the
wheels. To restart the vehicle when
it is already moving, use N (Neutral)
only. Also, use N (Neutral) when the
vehicle is being towed.
{CAUTION
Shifting into a drive gear while the
engine is running at high speed is
dangerous. Unless your foot is
rmly on the brake pedal, the
vehicle could move very rapidly.
You could lose control and hit
people or objects. Do not shift
into a drive gear while the engine
is running at high speed.
Notice:Shifting out of P (Park)
or N (Neutral) with the engine
running at high speed may
damage the transmission. The
repairs would not be covered by
the vehicle warranty. Be sure
the engine is not running at high
speed when shifting the vehicle.D (Drive):This position is for
normal driving. It provides the best
fuel economy. If you need more
power for passing, and you are:
Going less than 35 mph
(56 km/h), push the accelerator
pedal about halfway down.
Going about 35 mph (56 km/h)
or more, push the accelerator
all the way down.
Notice:If the vehicle seems to
start up rather slowly or not shift
gears when you go faster, and you
continue to drive the vehicle that
way, you could damage the
transmission. Have the vehicle
serviced right away. You can drive
in L2 (Low) when you are driving
less than 35 mph (56 km/h) and
D (Drive) for higher speeds
until then.
2 (Second):This position reduces
vehicle speed more than D (Drive)
without using the brakes. You
can use 2 (Second) on hills.
Driving and Operating 8-7
2009 - Pontiac Vibe Owner Manual