2009 Peugeot 607 Dag ESP

3
48
Memorising driving and mirror positions
Memorising using the controls on
the driver's door
To memorise:

 Place the key in the ignition on po-
sition,

 Adjust your seat and mirrors,

 Press button M , then button 1 "fi rst
driving position" or button 2 "sec-
ond driving position" within four
seconds.
An audible signal confi rms that a position
has been memorised.
Memorising a new position cancels
the previous one. Recalling a memorised driving
position
Ignition on, vehicle stationary

 Briefl y press button 1 or 2 to recall
the corresponding memorised po-
sition. The end of the setting is in-
dicated by a bleep.
After recalling a memorised position
a few times in succession, the func-
tion will be cancelled until the engine
is started.
G - Heated seats adjustment
With the engine running, use the cor-
responding adjustment dial to select
the required degree of heating:

0
: Off.

1
: Low.

2
: Medium.

3
: High. The electrical adjustments of the seat
and exterior mirrors are memorised.
Two driving positions can be memo-
rised using buttons
M/1 and M/2 . Vehicle moving

 Keep button 1 or 2 pressed down
until the bleep indicates that set-
ting of the corresponding memo-
rised position is complete.

3
49
REAR SEATS
Folding down the seat back Rear heated seats controls
The seat back in the rear is folded
down in two 1/3-2/3 parts.
Before folding down the seat back:

 check that the seat belt strap on
the side of the seat back (1/3 or
2/3) is positioned correctly,

 release the lap belt strap by press-
ing the black button of the lock
(2/3).
 Press the switch. The temperature
is regulated automatically.

 Press it again to stop operation.

Note: the command to activate heat-
ing of the seat(s) remains in the mem-
ory for one minute after the ignition is
switched off.
The unlocking controls are located in
the boot.
To unlock from the boot:

 pull the control A corresponding to
the part of the seat back that you
wish to fold down.
To unlock from inside the vehicle:

 lower the armrest and open the ski
fl ap,

 pull the button B located on the un-
locking housing corresponding to
the part of the seat back that you
wish to fold down.
Rear seat
When returning the seat back
to its original position, en-
sure that the seat belt is not
trapped. When putting the seat back to
its original position, for your
safety make sure that it is cor-
rectly locked.

5
68
LIGHTS STALK
Lights off.
Side lights. Dipped/main beam head-
lamps. Dipped/main beam change

 Pull the stalk fully towards you.
Lights on
With the ignition and the automatic
lights function switched off, on open-
ing the driver's door a buzzer sounds
to warn you that you have left your
lights on.
Front and rear fog lamps (ring B)

 Turn ring B forwards to switch on
and backwards to switch off. The
position is confi rmed by the light
on the instrument panel.
Front fog lamps (one press)
These operate with the side lights, dipped
headlamps or main beam headlamps.
Rear fog lamps (two presses)
These operate with the side lights and
the front fog lamps, or with the dipped
headlamps.
Left: downwards.

Right: upwards.
Direction indicators (fl ashers)

Note: if you forget to return
the direction indicator to its
normal position, the volume
of the audible signal will in-
crease, if you are driving at a speed
greater than 50 mph (80 km/h).
Parking lights
The side lights are lit on the side the
traffi c is on.
With the ignition off and within the next
minute, place the direction indicators
stalk on the traffi c side (for example:
for parking on the right; switching on
of the lights on the left).
This is indicated by an audible sig-
nal and lighting of the corresponding
direction indicator on the instrument
panel.
Automatic "follow-me-home"
lighting
When you leave your vehicle with the
automatic switching on of the lights
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To deactivate or activate this func-
tion, pass via the multifunction display

" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
Front and rear lights (ring A)

 Turn ring A to the position required.

7
78
The switch lights up and the
warning light comes on: the
ASR and ESP systems no
longer have any effect on the
engine operation.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to be
improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and that
required by the driver, the ESP system
automatically acts on the engine and
the brake of one or more wheels, in or-
der to put the vehicle back on course,
within the limits of the laws of physics.
Operation of the ASR and ESP
systems The warning light fl ashes
when the ASR or ESP is ac-
tivated. Disarming
Reactivation:

 Automatic if the ignition is switched
off.

 Automatic from 30 mph (50 km/h).

 Manual by pressing the switch
again. When a malfunction of the
systems occurs, the switch
light fl ashes and the warn-
ing light comes on, accom-
panied by an audible signal
and a message on the multi-function
display.
Contact a PEUGEOT dealer to have
the system checked.
The ASR/ESP systems offer
exceptional safety in normal
driving, but this should not en-
courage the driver to take extra
risks or drive at high speed.
The correct functioning of these sys-
tems depends on observation of the
manufacturer's recommendations re-
garding the wheels (tyres and rims), the
braking components and the electronic
components, as well as the PEUGEOT
assembly and operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer.
When the ignition is on, the
ASR and ESP systems are
always activated. Operating check
Activation of the ASR and ESP
systems In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground), it may be ad-
visable to disarm the ASR and ESP
systems, so that the wheels can move
freely and regain grip.

 Press the "ESP OFF" switch, lo-
cated under the steering wheel to
the right.

7
79
TYRE UNDER-INFLATION
DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction (speed greater
than 15 mph [25 km/h]). Sensor(s) not detected
This warning light, accompa-
nied by an audible signal and a
message on the multifunction
display, indicates that under-in-
fl ation detection is absent from
one (or several) tyre(s).
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Pressure check
With the ignition on and after
the engine oil level, this warn-
ing light comes on to indicate
that the system is measuring
the pressure of the tyres.
Pressure OK This warning light comes on
if all of the tyre pressure val-
ues measured are correct.
If one of the warning lights
described below appears,
refer to the corresponding paragraph.
If none of the lights appear, contact a
PEUGEOT dealer to have the system
checked. Under-infl ated tyre
This warning light comes on,
accompanied by an audible
signal and a message on the
multifunction display, locat-
ing the defl ated tyre.
Have the tyre pressure checked as
soon as possible.
Puncture
This warning light, accom-
panied by an audible signal
and a message on the multi-
function display locating the
punctured tyre, is followed
by illumination of the STOP-
warning light.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
very defl ated) tyre, and have the tyre
pressure checked as soon as possible. All repairs and changing of
tyres on a wheel fi tted with this
system must be carried out by
a PEUGEOT dealer.

The tyre under-infl ation detection
system is an aid to driving which
does not replace the need for the
driver to be vigilant or to drive re-
sponsibly.
This system does not remove the ne-
cessity for having the tyre pressure
(including that of the spare wheel)
checked regularly, to ensure optimum
dynamic performance of the vehicle
and to prevent premature wear of the
tyres, particularly in the case of ardu-
ous driving conditions (heavy load,
high speed).
The system may temporarily be disturbed
by radio broadcasts on a frequency close
to it.

Note: if the damaged tyre is
temporarily stored in the boot,
it will again emit this message
to remind you of the necessity
of having it repaired. This will prevent
another warning of the same type be-
ing displayed.
Note: this message is also
displayed when one of the
tyres is away from the vehi-
cle (being repaired) or when a
wheel without a sensor is fi tted.

8
86
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX
Gear selection gate

 Move the lever in the gate to select
a position.
The indicator light corresponding to
the position selected appears on the
instrument panel screen.
Starting the engine

 with the handbrake on, select posi-
tion P or N in the gate,

 turn the ignition key.
Moving Off
With the engine running, from posi-
tion P :

 to exit position P, it is essential
to press the brake pedal,

 select position R , D or M , then gra-
dually release the pressure on the
brake pedal; the vehicle moves off
immediately.
To move off from position N :

 with your foot on the brake, release
the handbrake,

 select position R , D or M , then gra-
dually release the pressure on the
brake pedal; the vehicle moves off
immediately.
When the engine is at idle,
brakes not applied, if position

R , D or M is selected, the ve-
hicle moves even without the
accelerator being pressed.

Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the engi-
ne running, as the vehicle moves
even without the accelerator being
pressed.
The six speed automatic gearbox of-
fers, as required, the comfort of the
automatic program, enhanced by a
manual selection suited to dynamic
driving conditions: Sport program.
Driving on a slippery road is detected
automatically.
However, manual selection is still pos-
sible using the gear lever.
P ark: to immobilise the vehicle and to
start the engine, with the handbrake
on.

R everse: to reverse (select this posi-
tion with the vehicle stationary, engine
at idle).

N eutral: to start the engine and to park,
with the handbrake on.

Note: if position N is inadvertently
engaged while driving, allow the en-
gine to return to idle before engaging
position D then accelerate.

D rive: to drive in automatic mode.

M anual: to drive selecting the gears.

S : Sport program.

8
89
CRUISE CONTROL/
SPEED LIMITER
Selecting the function

 Place switch 1 in the CRUISE
position. The cruise control is not
yet active and no speed has been
memorised. The display indicates: Cancelling the memorised speed
If you wish to cancel the memorised
speed:

 Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
Switching the function off

 Place switch 1 in position 0 or LIMIT
to switch the system off.
First activation/memorising a
speed
As soon as you reach the cho-
sen speed, press button "set-" 2 or
"set+" 3 . This memorises the speed,
which will be maintained automatically.
The display indicates (e.g. at 70 mph
(110 km/h)):

Note: It is possible to acce-
lerate and drive momentarily
at a speed greater than the
memorised speed. The value
memorised fl ashes. When the accele-
rator pedal is released, the vehicle will
return to the memorised speed.
Note: the speed memorised
is cancelled automatically if
the vehicle speed is less than
25 mph (40 km/h), or if the
manual gearbox is in a gear lower than
fourth (second gear for the automatic
gearbox) or if the ESP is activated.
On a steep descent, the cruise
control, which does not act on
the brakes, will not be able to
prevent the vehicle from excee-
ding the programmed speed.
The cruise control cannot, in any circums-
tances, replace the need to comply with
speed limits or the need for vigilance and
responsibility on the part of the driver.
It is advisable to keep your feet near
the pedals at all times.
Cruise control function
This enables the vehicle to maintain a
steady speed programmed by the driver.
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged for vehicles fi tted with a
manual gearbox.
On vehicles fi tted with an automatic
gearbox, the lever must be in position D
or at least second gear must be enga-
ged in sequential driving mode.

8
91
Memorising a speed
A speed can be memorised without
activation of the limiter.
A brief press on buttons 2 and 3 de-
creases or increases by 1 mph (1 km/h).
A maintained press decreases or in-
creases the memorised speed progres-
sively in steps of 5 mph (5 km/h).
Switching the function off

 Place switch 1 in position 0 or

CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in the
memory. Activation/deactivation of the
limiter
The activation is taken into account,
when the vehicle is moving, when the
vehicle speed is at least 5 mph (5 km/h)
below the stored speed.
Pressing button
4 activates the limiter,
pressing this button again deactivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):
Exceeding the programmed speed
In exceptional situations, this method
can be used to exceed the program-
med speed.
Pressing the accelerator to exceed the
programmed speed will have no effect
unless the pedal is pressed fi rmly to
the end of its travel (passing the point
of resistance ).
The limiter is deactivated temporarily
and displays the speed which fl ashes
(e.g. at 70 mph (110 km/h)): To re-activate the limiter, release the
accelerator to slow down to a speed
below the programmed speed.
Operating check
In the event of a limiter malfunction,
the memorised speed is erased, the
dashes fl ash for a few seconds:
To prevent the mat from beco-
ming caught under the pedals: - ensure that the mat is po- sitioned correctly,
- never fi t one mat on top of another.
Contact a PEUGEOT dealer to have
the system checked.
Selecting the function

 Place switch 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default the display indicates:
Note: sometimes (on a steep
descent), the limiter may not
prevent the vehicle from ex-
ceeding the programmed
speed, this speed fl ashes.
On a steep descent or if you
accelerate sharply, the speed
limiter, which does not act on
the brakes, will not be able to
prevent the vehicle from exceeding
the programmed speed.
The speed limiter cannot, in any cir-
cumstances, replace the need to com-
ply with speed limits or the need for
vigilance and responsibility on the part
of the driver.