2009 Peugeot 407 gearbox
[x] Cancel search: gearboxPage 115 of 250
8DRIVING
97
CRUISE CONTROL/SPEED LIMITER Selecting the function
Place switch 1 in the CRUISE
position. The cruise control is not
yet active and no speed has been
memorised. The display indicates:
Switching the function off
Place switch 1 in position 0 or
LIMIT to switch the system off.
Note: It is possible to acceler-
ate and drive momentarily at a
speed greater than the memo-
rised speed. The value memo-
r i s e d fl a s h e s . W h e n t h e a c c e l e r a t o r
pedal is released, the vehicle will return
to the memorised speed.
Cancelling the memorised speed
If you wish to cancel the memorised
speed:
Press button 4 or the brake or
clutch pedal. The display indicates
(e.g. at 70 mph (110 km/h)):
Activation/memorising a speed
As soon as you reach the chosen speed,
press button 2 or 3 . This memorises the
speed, which will be maintained auto-
matically. The display indicates (e.g. at
70 mph (110 km/h)): On a steep descent, the cruise
control, which does not act on
the brakes, is not able to prevent
the vehicle from exceeding the
programmed speed.
In no circumstances does the cruise
control replace the requirement to
respect speed limits, nor does it replace
the need for vigilance and responsibility
on the part of the driver.
We recommend that your feet remain
near the pedals.
Cruise control function
This enables the vehicle to maintain
a steady speed programmed by the
driver.
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged (second gear for the
automatic gearbox),
with the engine
running .
Page 116 of 250
8DRIVING
98
Note: the speed memo-
rised is cancelled auto-
matically if the vehicle
speed is less than 25 mph
(40 km/h), or if the manual gearbox
is in a gear lower than fourth (second
gear for the automatic gearbox) or if
the ESP is activated. Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
t h e d a s h e s fl a s h f o r a f e w s e c o n d s :
Contact a PEUGEOT dealer to have
the system checked. Do not use the cruise control
on slippery roads or in heavy
t r a f fi c .
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
To memorise a speed lower than the
previous one:
press button 2 ;
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase
or decrease of the value in steps of
5 mph (5 km/h).
Recalling the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memo-
rised speed. The display indicates
(e.g. at 70 mph (110 km/h)):
Cancelling the memorised speed
Place switch 1 in position 0 or LIMIT
or switch off the ignition.
Page 129 of 250
1010PRACTICAL INFORMATION
112
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel securing
bolts.
2. Jack with integrated handle.
Permits raising of the vehicle.
3. Removable towing eye.
See corresponding section.
4. Bolt cover tool.
Permits removal of the bolt protectors (covers) on alloy wheels. Removal
For vehicles with steel wheels,
detach the trim using the wheel-
brace 1 pulling at the valve pas-
sage hole.
For vehicles with alloy wheels,
remove the covers using tool 4 .
Loosen the wheel bolts.
Take the jack from the tool kit.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Access to the spare wheel and the
jack in the boot
L i f t t h e fl o o r u s i n g t h e l i f t i n g h a n d l e .
Secure the handle behind the boot
seal. Never go underneath a vehicle
which is supported only by a
jack.
Park the vehicle on level, stable
and non-slippery ground.
Apply the handbrake, switch off the
i g n i t i o n a n d e n g a g e fi r s t o r r e v e r s e
gear (position P for the automatic
gearbox).
Page 130 of 250
1010PRACTICAL INFORMATION
113
Fitting a wheel
Position the wheel.
Tighten the bolts by hand.
Partly tighten the bolts using the
wheelbrace.
Fold the jack 2 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
For vehicles with steel wheels,
r e fi t t h e w h e e l t r i m s t a r t i n g b y p l a c -
ing its notch facing the valve and
press with the palm of the hand.
F o r v e h i c l e s w i t h a l l o y w h e e l s , r e fi t
the covers.
Put the tool holder back in position.
T h i s h e l p s t o k e e p t h e b o o t fl o o r i n
its correct position, to prevent any
d e f o r m a t i o n o f t h e fl o o r w h e n l o a d e d .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
light
Information on the instrument
panel:
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
-
w i t h fi r s t o r r e v e r s e g e a r e n g a g e d ( p o -
sition P for the automatic gearbox),
- never go underneath a vehicle
which is supported only by a jack. T y r e u n d e r - i n fl a t i o n d e t e c t i o n
system warning light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
After changing the wheel:
- have the tightening of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired a n d r e fi t i t t o t h e v e h i c l e a s s o o n a s
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using the
temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,
- d o n o t fi t a w h e e l t r i m ,
- drive carefully,
- c h e c k t h e i n fl a t i o n p r e s s u r e i n d i - cated on the label.
* According to version and country.
Page 140 of 250
1010PRACTICAL INFORMATION
120
Fuse N°
Rating
A
Functions
G29 5 Telematics (according to country).
G30 30 Driver’s electric seat.
G31 30 Passenger’s electric seat.
G32 15 Rear 12V accessories socket (100 W max).
G33 - Not used.
G34 - Not used.
G35 - Not used.
G36 - Not used.
G37 15 Six-speed automatic gearbox supply.
G38 30 Right and left heated seats.
G39 - Trailer fuse box (accessory).
G40 30 Audio Hi-Fi assembly.
Page 142 of 250
1010PRACTICAL INFORMATION
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
r e fi t t h e b a t t e r y c o v e r w h e n y o u h a v e
fi n i s h e d .
Fuse N°
Rating
A
Functions
1 20 Engine management control unit.
2 15 Horn.
3 10 Front and rear wash-wipe.
4 20 Headlamp wash.
5 15 Engine management actuators (fuel pump,
purge canister solenoid valves, ...).
6 10 Automatic gearbox control unit.
7 10 Switching and protection unit, intake air
fl o w s e n s o r , c l u t c h s w i t c h , s i x - s p e e d
automatic gearbox switch, STOP switches,
electrochromatic mirror, panoramic roof
c o n c e a l i n g fl a p c o n t r o l s ( 4 0 7 S W ) .
8 20 Starter coil.
9 10 Xenon bulb electronic supply, STOP switch,
power steering electropump assembly,
four-speed automatic gearbox control unit,
automatic gearbox locking relay.
10 30 Engine management actuators (ignition coil,
solenoid valves, oxygen sensors).
11 40 Air conditioning blower or not used.
12 30 Windscreen wipers.
13 40 Built-in systems interface supply
(ignition positive).
14 30 Air pump.
Page 147 of 250
1010PRACTICAL INFORMATION
125
Without lifting
(4 wheels on the ground)
You must always use a towbar.
The removable towing eye is inside
the spare wheel.
At the front and at the rear:
Unclip the cover,
Screw in the towing eye as far as it
will go. Special features of the
automatic gearbox
When towing with the engine switched
off, there is no braking or steering
assistance.
Failure to observe this special require-
ment may lead to the destruction of
certain braking units and the absence
of braking assistance when the engine
is re-started.
TOWING YOUR VEHICLE
Lifting
(2 wheels only on the ground)
It is preferable to raise the vehicle with
a professional lifting device.
Place the gear lever in neutral
(position N in the case of the
automatic gearbox).
Towing a vehicle with an auto-
matic gearbox in reverse gear
is prohibited (absence of lubri-
cation). When towing with four wheels on the
ground, the following rules must be
obeyed:
- lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.
Page 149 of 250
1010PRACTICAL INFORMATION
127
In all cases, pay attention to the cool-
ant temperature. Lighting TOWING A TRAILER, CARAVAN, BOAT, ETC...
We recommend the use of original
PEUGEOT towbars and their harnesses
which have been tested and approved
from the design stage of your vehicle
a n d t h a t y o u e n t r u s t t h e fi t t i n g o f t h e
towbar to a PEUGEOT dealer.
I f t h e t o w b a r i s n o t fi t t e d b y a P E U G E O T
d e a l e r , i t i s i m p e r a t i v e t h a t i t i s fi t t e d u s -
ing the electrical pre-equipment installed
at the rear of the vehicle, in accordance
with the manufacturer’s instructions.
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heavi-
est loads are as close as possible to
the axle and the nose weight is close
to the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope in-
creases the coolant temperature.
As the fan is electrically controlled, its
cooling capacity is not dependent on
the engine speed.
I n t h e c a s e o f v e h i c l e s fi t t e d w i t h a n
HDI engine, it is advisable, following
intensive use (towing on a motorway,
prolonged driving, ...), to leave the en-
gine running at idle for approximately
20 seconds before switching off the ig-
nition. This limits any increase in the
temperature of the engine after it has
been switched off.
Note: in certain cases of par-
ticularly arduous use (towing
the maximum load in high
temperatures on a steep
slope), the engine automatically lim-
its its power and selects the appropri-
ate automatic gearbox gear in manual
mode. In this case, cutting off the air
conditioning allows the engine power
to be recovered, and therefore the
towing capacity to be increased.
If the coolant temperature
warning light comes on, stop
the vehicle and switch off the
engine as soon as possible.
Tyres: check the tyre pressures of the
towing vehicle (label on the central
door pillar on the driver’s side) and of
the trailer towed, observing the recom-
mended pressure.
Brakes: towing increases the braking
distance. Drive at a moderate speed,
change down early and brake gradu-
ally.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. Manual adjustment
Adjust your headlamps so as not to
dazzle other road users. Check the
electrical signalling of the trailer.