2009 Peugeot 407 boot
[x] Cancel search: bootPage 74 of 250
4ACCESS
66
ALARM When the alarm is triggered, the siren
sounds and the direction indicator lights
fl a s h f o r a p p r o x i m a t e l y t h i r t y s e c o n d s .
After triggering, the alarm remains set,
ten times in succession.
On the eleventh time it will become
inactive again, until the next cycle of
disarming then setting of the alarm.
Warning: if button A indicator light
fl a s h e s r a p i d l y , t h e a l a r m h a s b e e n
triggered while you were away from
your vehicle.
Note: if the alarm has been triggered
i n y o u r a b s e n c e , t h i s fl a s h i n g s t o p s
when the ignition is switched on. Remote control failure,
alarm set
Unlock the doors with the key and
o p e n t h e d o o r . T h e a l a r m i s t r i g -
gered.
Switch on the ignition. The alarm is
disarmed.
* According to country.
Setting the alarm
Switch off the ignition and get out
of the vehicle.
S e t t h e a l a r m , b y l o c k i n g o r d e a d -
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once per second).
If you wish to lock or deadlock your
vehicle without setting the alarm, lock
it (one turn of the key) or deadlock it
( a s e c o n d t u r n w i t h i n fi v e s e c o n d s
maximum) using the lock. Disarming
Unlock the vehicle with the remote
control key.
The alarm is disarmed, indicator light
A
goes out when the ignition is switched on
(unless the alarm has been triggered).
To set the alarm with exterior
protection only
If, while you are away from the vehicle,
you wish to leave a window partially
open or a pet inside the vehicle, you
should choose exterior protection only.
Switch off the ignition,
I n t h e n e x t t e n s e c o n d s , p r e s s b u t -
ton A until the indicator light is on
continuously,
Get out of the vehicle,
S e t t h e a l a r m b y l o c k i n g o r d e a d -
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once a second). Incorrect operation
When the ignition is switched on, if
button
A lights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
Automatic activation *
The alarm is activated automatically
two minutes after the last closure of a
door or the boot.
In order to avoid accidental triggering
of the alarm when a door or the boot
is opened, it is essential to press the
unlocking button on the remote control
again.
When the alarm is set, if a door,
the tailgate or the bonnet is
not closed correctly, the siren
i s t r i g g e r e d b r i e fl y . I f t h e v e h i -
cle is closed correctly within the next
45 seconds, the alarm is set. In all cases,
the alarm is set after 45 seconds.
This provides two types of surveillance:
-
exterior protection: it sounds if
a door, the boot or the bonnet is
opened. - interior protection: it sounds if the
v o l u m e i n s i d e t h e p a s s e n g e r c o m p a r t -
ment changes (breaking of a window
or a movement inside the vehicle).
Page 76 of 250
4ACCESS
68
BOOT (SALOON) TAILGATE AND REAR SCREEN (407 SW) Partial opening of the rear screen
Opening the tailgate and rear
screen
The tailgate and rear screen cannot
be opened at the same time.
With the rear screen closed, to open
the tailgate , operate the handle A ,
then lift the tailgate.
With the tailgate closed, to open the
rear screen , operate the handle B ,
then lift the rear screen.
The lighting is controlled by opening
the tailgate or the rear screen.
If the permanent locking of the
boot is activated, opening is
only possible by pressing the
remote control button.
Notes: the tailgate and rear
screen lock automatically when
driving at 6 mph (10 km/h) and
unlock when one of the doors
is opened.
When the rear wiper is in a wiping
position, the rear screen cannot be
opened until the end of the cycle.
Close the rear screen using the wiper
arm or by pressing the centre of the
glass.
T o o p e n t h e b o o t , p r e s s t h e p u s h b u t -
ton and raise the tailgate.
The locking or unlocking of the tailgate
and rear screen is simultaneous with
that of the doors. With the tailgate closed, to partially
open the
rear screen , press and hold
the unlocking button C on the remote
control.
Page 77 of 250
4ACCESS
68
BOOT (SALOON) TAILGATE AND REAR SCREEN (407 SW) Partial opening of the rear screen
Opening the tailgate and rear
screen
The tailgate and rear screen cannot
be opened at the same time.
With the rear screen closed, to open
the tailgate , operate the handle A ,
then lift the tailgate.
With the tailgate closed, to open the
rear screen , operate the handle B ,
then lift the rear screen.
The lighting is controlled by opening
the tailgate or the rear screen.
If the permanent locking of the
boot is activated, opening is
only possible by pressing the
remote control button.
Notes: the tailgate and rear
screen lock automatically when
driving at 6 mph (10 km/h) and
unlock when one of the doors
is opened.
When the rear wiper is in a wiping
position, the rear screen cannot be
opened until the end of the cycle.
Close the rear screen using the wiper
arm or by pressing the centre of the
glass.
T o o p e n t h e b o o t , p r e s s t h e p u s h b u t -
ton and raise the tailgate.
The locking or unlocking of the tailgate
and rear screen is simultaneous with
that of the doors. With the tailgate closed, to partially
open the
rear screen , press and hold
the unlocking button C on the remote
control.
Page 78 of 250
4ACCESS
69
"Rear screen open" warning
When the engine is running, if the
rear screen is not fully closed, you are
w a r n e d b y a m e s s a g e o n t h e m u l t i -
function display.
When the vehicle is moving (speed
greater than 6 mph (10 km/h)), if the
rear screen is not fully closed, you are
w a r n e d b y a n a u d i b l e s i g n a l , a m e s -
sage on the multifunction display and
lighting of the service warning light. Tailgate release
T h i s e n a b l e s t h e t a i l g a t e t o b e u n -
locked in the event of a central locking
fault.
- F o l d b a c k t h e r e a r s e a t s t o g a i n
access to the lock from inside the
boot,
- I n s e r t a s m a l l s c r e w d r i v e r i n t o h o l e A
of the lock to unlock the tailgate.
Page 93 of 250
5
79
REAR COURTESY LIGHT ( S A L O O N ) REAR READING LIGHTS ( 4 0 7 S W ) Sill illumination
T h e s i l l l i g h t i n g i s a t t h e b o t t o m o f e a c h
door panel.
T h e l a m p s c o m e o n a u t o m a t i c a l l y
when a door is opened and switch off
a u t o m a t i c a l l y w h e n a l l o f t h e d o o r s a r e
closed.
Boot light
The boot light is located in the right-
h a n d b o o t t r i m .
I t c o m e s o n a u t o m a t i c a l l y w h e n t h e
boot is opened and switches off auto-
m a t i c a l l y w h e n t h e b o o t i s c l o s e d .
1. Courtesy light
2. Map reading lights
With the key in the ignition on or starting
position, operate the relevant switch.
T h e r e a r c o u r t e s y l i g h t c o m e s o n w h e n t h e
i g n i t i o n k e y i s r e m o v e d , o n u n l o c k i n g t h e
vehicle or on opening one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.
Pressing switch 1 turns on the rear
courtesy light.
The courtesy light can be deactivated
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l i g h t s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
To re-activate the lights, press the
switch, with the door open. With the key in the ignition on or starting
position, press the corresponding
switch.
T h e r e a r r e a d i n g l i g h t s c o m e o n w h e n
t h e k e y i s r e m o v e d f r o m t h e i g n i t i o n
and when the vehicle is unlocked.
They switch off gradually when the
ignition is switched on or when the
vehicle is locked.
Pressing switch 1 switches on the
rear reading light concerned for
t e n m i n u t e s .
Page 96 of 250
6LAYOUT
8 2
BOOT LAYOUT (407 SW)
3. Load space cover
T o r e m o v e :
U n c l i p t h e f r o n t e n d s a n d r e m o v e
t h e l o a d s p a c e c o v e r .
T o i n s t a l l :
P o s i t i o n t h e f r o n t e n d s o f t h e l o a d
s p a c e c o v e r o n i t s s u p p o r t a n d
p r e s s l i g h t l y t o p u t i t i n p l a c e .
1. 12 V accessories socket
(100 W max) and boot light
T h i s i s a l i g h t e r t y p e 1 2 v o l t s o c k e t . I t
i s i n s t a l l e d o n t h e r e a r l e f t t r i m a n d i s
s u p p l i e d f r o m t h e i g n i t i o n o n p o s i t i o n .
T h e b o o t l i g h t i s c o n t r o l l e d b y o p e n i n g
t h e t a i l g a t e o r r e a r s c r e e n .
4. Stowing rings
T h e r e a r e f o u r s t o w i n g r i n g s o n t h e b o o t
fl o o r t o w h i c h t h e l u g g a g e r e t a i n i n g n e t
c a n b e a t t a c h e d .
2. Storage boxes
T h e r e a r e t w o s i d e s t o r a g e b o x e s
w h i c h c a n c o n t a i n :
- o n t h e l e f t : a c a n o f o i l , a fi r s t a i d
k i t , a p u n c t u r e r e p a i r a e r o s o l ,
- o n t h e r i g h t ( e x c e p t w h e n a J B L H i - F i s y s t e m i s fi t t e d ) : a b o x o f
b u l b s , a w a r n i n g t r i a n g l e ( s u p p o r t
p r o v i d e d f o r t h i s p u r p o s e ) , t h e l u g -
g a g e r e t a i n i n g n e t .
Page 129 of 250
1010PRACTICAL INFORMATION
112
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel securing
bolts.
2. Jack with integrated handle.
Permits raising of the vehicle.
3. Removable towing eye.
See corresponding section.
4. Bolt cover tool.
Permits removal of the bolt protectors (covers) on alloy wheels. Removal
For vehicles with steel wheels,
detach the trim using the wheel-
brace 1 pulling at the valve pas-
sage hole.
For vehicles with alloy wheels,
remove the covers using tool 4 .
Loosen the wheel bolts.
Take the jack from the tool kit.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Access to the spare wheel and the
jack in the boot
L i f t t h e fl o o r u s i n g t h e l i f t i n g h a n d l e .
Secure the handle behind the boot
seal. Never go underneath a vehicle
which is supported only by a
jack.
Park the vehicle on level, stable
and non-slippery ground.
Apply the handbrake, switch off the
i g n i t i o n a n d e n g a g e fi r s t o r r e v e r s e
gear (position P for the automatic
gearbox).
Page 130 of 250
1010PRACTICAL INFORMATION
113
Fitting a wheel
Position the wheel.
Tighten the bolts by hand.
Partly tighten the bolts using the
wheelbrace.
Fold the jack 2 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
For vehicles with steel wheels,
r e fi t t h e w h e e l t r i m s t a r t i n g b y p l a c -
ing its notch facing the valve and
press with the palm of the hand.
F o r v e h i c l e s w i t h a l l o y w h e e l s , r e fi t
the covers.
Put the tool holder back in position.
T h i s h e l p s t o k e e p t h e b o o t fl o o r i n
its correct position, to prevent any
d e f o r m a t i o n o f t h e fl o o r w h e n l o a d e d .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
light
Information on the instrument
panel:
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
-
w i t h fi r s t o r r e v e r s e g e a r e n g a g e d ( p o -
sition P for the automatic gearbox),
- never go underneath a vehicle
which is supported only by a jack. T y r e u n d e r - i n fl a t i o n d e t e c t i o n
system warning light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
After changing the wheel:
- have the tightening of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired a n d r e fi t i t t o t h e v e h i c l e a s s o o n a s
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using the
temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,
- d o n o t fi t a w h e e l t r i m ,
- drive carefully,
- c h e c k t h e i n fl a t i o n p r e s s u r e i n d i - cated on the label.
* According to version and country.