2009 PEUGEOT 308 SW BL boot

i
112
FITTINGS
Rear parcel shelf
This consists of four sections three of
which can be folded back on each other.
There are several options for storing the
rear parcel shelf:
- either folded back on itself near the rear seats (1),
- or folded back on itself and stored in a location provided under the rear
seats (2).
To fold it from the boot:

 unclip the load space cover from its
side supports,

 take hold of the load space cover by
its handle A ,

 fold it concertina-style to the rear
seats.
To unfold it from the boot:

 take hold of the load space cover by
its handle A ,

 unfold it to the boot pillars,

 clip the load space cover on its side
supports. Hooks
Maximum loads
7.5 kg, rear parcel shelf unfold-
ed with high load retaining net at
row 2. The hooks can be used to hold shop-
ping bags.

FITTINGS
BOOT FITTINGS

1. Load space
cover
(see details on following page)

2. Storage box

3. 12 V
accessories socket
(see details on following page)

4. Hooks
(see details on following page)

5. Stowing rings

6. High load retaining net
(see details on following page)

7. Rear armrests with
cup
holder

8. Luggage retaining strap

9. Location for torch
(see details on following page)

i
115
FITTINGS
Load space screen
To install the load space screen:

 position one of the ends of the roller
in its support,

 insert the second end in its support;
the catch locks automatically,

 unroll the load space screen to the
boot pillars,

 insert the load space screen guides
in the rails on the boot pillars.
To store the load space screen, place it
at the boot sill, roller uppermost and fl ap
facing inwards.
To remove the load space screen:

 remove the load space screen
guides from the rails on the boot
pillars,

 roll up the load space screen in its
roller,

 pull and support the catch at one of
the ends of the roller to release it,

 remove the roller from its support
from the released end, then from the
second.
You can access the boot by open-
ing the rear screen and raising the
load space screen fl ap.

!i
117
FITTINGS
Torch
This is a removable lamp, fi tted in the
boot wall, which can be used to light the
boot or as a torch.
For the boot lamp function, refer to the
"Visibility - § Boot lamp" section.
Operation
This torch operates with NiMH type re-
chargeable bateries.
It has an battery life of approximately
45 minutes and charges while you are
driving. Use

 Extract the torch from its location
pulling it upwards.

 Press the switch, located on the
back, to switch the torch on or off.

 Unfold the support, located on the
back, to set down and raise the
torch; for example, when changing
a wheel.
Storing

 Put the torch back in place in its
location starting with the lower part.
If you have forgotten to switch off the torch, this switches it off
automatically. Side blinds
Fitted on the rear windows of the 2nd
row, these protect your young children
from the sun.

 Pull the blind by the central tab.

 Position the blind attachments on
the corresponding hooks.
Observe the polarities when fi tting
the rechargeable batteries.
Never replace the rechargeable
batteries with normal batteries. It the torch is not engaged correct-
ly, it may not charge and may not
come on when the boot is opened.

i
i
135
SAFETY
2nd row rear centre
seat belt
Installation Removal and storing

 Press the red button on the buckle B ,
then on the buckle A .

 Guide the strap as it reels in and
bring the tongue B , then A onto the
magnet of the attachment point on
the roof.
3rd row rear seat belts
Installation


Pull the strap and insert the tongue C in the buckle, on the boot side trim
side.

 Insert the tongue D in the opposite
buckle.

 Check the fastening of each buckle
by pulling the strap.


Pull the strap and insert the tongue A
in the left-hand buckle.

 Insert the tongue B in the right-hand
buckle.

 Check the fastening of each buckle
by pulling the strap.
The seat belts for the rear seats of the
3rd row are located at the corner of the
corresponding boot pillar and roof. If the two outer seats of the 2nd row
are moved inwards, always use the
outer rear seat belts.
Removal and storing


Press the red button on the buckle D ,
then on the buckle C .

 Guide the strap as it reels in and
bring the tongue D , then C onto the
magnet of the attachment point on
the corresponding boot pillar.
The seat belt for the rear centre seat of
the 2nd row is located at the rear left of
the roof.
The 3rd row of seats (SW with
panoramic sunroof) is not fi tted
with seat belt unfastened warning
lamps.

11
i
165
PRACTICAL INFORMATION
This repair kit is available from
PEUGEOT dealers.
It is designed to repair most punc-
tures which could affect the tyre, lo-
cated on the tyre tread or shoulder.
Avoid removing any foreign bodies
which have penetrated the tyre.
TEMPORARY PUNCTURE REPAIR KIT
The kit is stowed in the boot below the
fl oor. It is fi tted in the tool box, located
below the storage compartment. Using the kit
This procedure, comprising several
steps, must be carried out in full.

 Switch off the ignition.


Turn the selector A to the "SEALANT"
position.

 Check that the switch B is in
position "0" .

 Connect the white pipe C to the
valve of the tyre to be repaired.

 Connect the compressor's electric
plug to the vehicle's 12 V socket.

 Affi x the speed limitation sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.

 Start the vehicle and leave the
engine running.
Access to the kit
Complete system consisting of a com-
pressor and an incorporated sealant
cartridge which permits
temporary re-
pair of the tyre so that you can drive to
the nearest garage.

11
i
168
PRACTICAL INFORMATION
This repair kit is available from
PEUGEOT dealers.
It is designed to repair holes of a
maximum diameter of 6 mm, only
where located on the tyre tread or
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
TEMPORARY PUNCTURE REPAIR KIT
Complete system consisting of a com-
pressor and a bottle of sealant which per-
mits temporary repair of the tyre so that
you can drive to the nearest garage.
The kit is stowed in the boot storage
tray. Using the kit

 Switch off the ignition.

 Tick the wheel to be repaired on the
speed limitation sticker enclosed
then affi x the sticker to the vehicle's
steering wheel to remind you that a
wheel is in temporary use.

 Clip the bottle 1 on the compressor 2 .

 Check that the switch A is tilted to
position "0" .

 Connect the pipe of the bottle 1 to
the valve of the tyre to be repaired.


Unwind the pipe of the compressor
2
fully, then connect it to the bottle.

 Connect the compressor's electric
plug to the vehicle's 12 V socket.

 Start the vehicle and leave the
engine running.

11
i
171
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed in the boot under
the fl oor.
To gain access to them:

 open the boot,

 raise the fl oor,

 secure it by hooking its cord on the
hook on the rear shelf support,

 unclip and remove the box containing
the tools. All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.

1. Wheelbrace.
For removal of the wheel trim and removal of the wheel fi xing bolts.

2. Jack with integral handle.
For raising the vehicle.

3. Socket for the security bolts
(located in the glove box).
For adaptation of the wheelbrace to the special security bolts.
List of tools
Access to the tools
Wheel with trim

When removing the wheel , detach the trim fi rst using the wheelbrace 1 pulling
at the valve passage hole.

When refi tting the wheel , refi t the trim starting by placing its notch facing the
valve and press around its edge with the palm of your hand.
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.