2009 Peugeot 308 CC Dag ignition
[x] Cancel search: ignitionPage 113 of 294
7
!
!
101
SAFETY
If at least one of the two air bag
warning lights come on continu-
ously, do not install a child seat on
the front passenger seat.
Have the system checked by a
PEUGEOT dealer.
Operating fault
If this warning light comes on on
the instrument panel, accompa-
nied by an audible warning and
a message on the multifunction
display, contact a PEUGEOT dealer to
have the system checked. The air bags
may no longer be triggered in the event
of a serious impact.
Reactivation
When you remove the child seat, turn
switch 1 to the "ON" position to re-arm
the air bag and so guarantee the safety
of your front passenger in the event of
an impact.
With the ignition on, this warn-
ing light comes on on the seat
belt and passenger's front air
bag warning lights display for
approximately one minute, if the pas-
senger's front air bag is activated. To guarantee the safety of your
child, it is imperative that the pas-
senger's front air bag is disarmed
when you install a "rear facing"
child seat on the front passenger
seat.
Otherwise, the child would risk be-
ing seriously injured or killed if the
air bag were triggered.
According to version, this warning
light comes on either on the
instrument panel or on the seat
belt and passenger's front air bag
warning lights display when the ignition is
on and until the air bag is re-armed. I f t h i s w a r n i n g l i g h t fl a s h e s ,
contact a PEUGEOT dealer.
The passenger's front air bag
may no longer be triggered in
the event of a serious impact.
Deactivation
Only the passenger's front air bag can
be disarmed:
with the ignition off, insert the key
in the passenger air bag disarming
switch 1 ,
turn it to the "OFF" position,
then, remove the key keeping the switch in this position.
Page 128 of 294
8
PRND
!
i
114
DRIVING
Stopping the vehicle
Before switching off the engine, you
can engage position P or N to place the
gearbox in neutral.
In both cases, apply the handbrake to
immobilise the vehicle. Operating fault
When the ignition is on, the
lighting of this warning light, ac-
companied by an audible signal
and a message on the multi-
function display, indicates a gearbox
malfunction.
In this case, the gearbox switches to
emergency mode and is locked in 3rd
gear. You may feel a substantial knock
when changing from P to R and from N
to R . This will not cause any damage to
the gearbox.
Do not exceed 60 mph (100 km/h), local
speed restrictions permitting.
Have it checked by a PEUGEOT dealer.
This warning light may also come on if a
door is opened.
I f t h e b a t t e r y i s fl a t a n d t h e l e v e r i s
in position P , it will not be possible
to change to another position.
Above all, do not force the lever as
this could damage the gearbox.
Manual operation
Select position M for sequential
changing of the four or six gears.
Push the lever towards the + sign to
change up a gear.
Pull the lever towards the - sign to
change down a gear.
D disappears and the gears
engaged appear in succes-
sion on the instrument panel.
In the event of under-revving
or over-revving, the gear se-
l e c t e d fl a s h e s f o r a f e w s e c o n d s , t h e n
the actual gear engaged is displayed.
It is possible to change from position D
(automatic) to position M (manual) at
any time.
When the vehicle is stationary or mov-
ing very slowly, the gearbox selects
gear M1 automatically.
The sport and snow programmes do not
operate in manual mode. If the lever is not in position
P ,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, an audible
signal is heard and a message ap-
pears.
Return the lever to position P ;
the audible signal stops and the
message disappears.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit; otherwise, the
gearbox will operate temporarily in auto-
matic mode.
Invalid value during manual operation
This symbol is displayed if a
gear is not engaged correctly
(selector between two posi-
tions).
Page 129 of 294
8
i
115
DRIVING
SPEED LIMITER
System which prevents the vehicle from
exceeding the speed programmed by
the driver.
When the programmed speed limit is
reached, pressing the accelerator pedal
no longer has any effect.
The speed limiter is switched on
manually: it requires a programmed
speed of at least 20 mph (30 km/h).
The speed limiter is switched off by
manual operation of the control.
The programmed speed can be ex-
ceeded temporarily by pressing the
a c c e l e r a t o r fi r m l y .
To return to the programmed speed,
simply slow down to a speed below the
programmed speed.
The programmed speed remains in the
memory when the ignition is switched off. The controls of this system are grouped
together on stalk
A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button
The programmed information is grouped
together on the instrument panel display.
5. Speed limiter on/off indication
6.
Speed limiter mode selection indication
7. Programmed speed value
Steering wheel controls Displays on the instrument
panel
The speed limiter cannot, in any
circumstances, replace the need
to respect speed limits, nor can it
replace the need for vigilance and
responsibility on the part of the
driver.
Page 131 of 294
8
i
117
DRIVING
CRUISE CONTROL
System which automatically maintains
the speed of the vehicle at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is switched on
manually: it requires a minimum vehicle
speed of 25 mph (40 km/h) and the en-
gaging:
- of fourth gear on the manual gearbox,
- of second gear on the automatic gearbox, in sequential driving mode,
-
of position D on the automatic gearbox.
The cruise control is switched off
manually or by pressing the brake or
clutch pedal or on triggering of the ESP
system for safety reasons.
It is possible to exceed the programmed
speed temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value. The controls of this system are grouped
together on lever
A .
1. Cruise control mode selection dial
2. Speed programming/value decrease
button
3. Speed programming/value increase
button
4. Cruise control off/resume button The programmed information is grouped
together on the instrument panel display.
5. Cruise control off/resume indication
6.
Cruise control mode selection indication
7. Programmed speed value
Steering wheel controls Displays on the instrument
panel
The cruise control cannot, in any
circumstances, replace the need
to respect speed limits, nor can it
replace the need for vigilance and
responsibility on the part of the
driver.
You are advised to keep your feet
near the pedals at all times.
Page 139 of 294
9CHECKS
CHECKING LEVELS
Check all of these levels regularly and top
them up if necessary, unless otherwise
indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding circuit checked by a
PEUGEOT dealer. Brake fluid level
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Oil level The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when the
ignition is switched on using the oil level
indicator on the instrument panel, or
using the dipstick.
Between two oil changes, the consump-
tion should not exceed 0.5 litre per
600 miles (1.000 km). T h e b r a k e fl u i d l e v e l s h o u l d b e
close to the "MAX" mark. If it is
not, check the brake pad wear.
Draining the circuit
Refer to the servicing booklet for details
of the interval for this operation.
Power steering fluid level T h e p o w e r s t e e r i n g fl u i d l e v e l
should be close to the "MAX"
mark. Unscrew the cap, with the
engine cold, to check the level. Screenwash and headlamp
wash fluid
I n t h e c a s e o f v e h i c l e s fi t t e d
with headlamp washers, the
m i n i m u m l e v e l o f t h i s fl u i d i s
indicated by an audible signal
and a message on the multi-
function display.
Top up the level when you stop the vehicle.
Draining the engine
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your engine
and conform to the manufacturer's recom-
mendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
Draining the circuit
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e t o p p e d
up or replaced with water.
Coolant level
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tempera-
ture of the coolant is regulated by the fan.
This can operate with the ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold. F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer's recommendations.
Page 162 of 294
10
!
!
i
148
PRACTICAL INFORMATION
Do not disconnect the terminals
w h i l e t h e e n g i n e i s r u n n i n g .
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
T h e b a t t e r i e s c o n t a i n h a r m f u l s u b -
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
m u s t n o t , i n a n y c i r c u m s t a n c e s , b e
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
a n d v e h i c l e b a t t e r i e s t o a s p e c i a l
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
F o l l o w t h e i n s t r u c t i o n s f o r u s e p r o -
v i d e d b y t h e m a n u f a c t u r e r o f t h e
c h a r g e r .
R e c o n n e c t s t a r t i n g w i t h t h e n e g a t i v e
t e r m i n a l ( - ) .
C h e c k t h a t t h e t e r m i n a l s a n d c o n n e c -
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
s u l p h a t e ( w h i t i s h o r g r e e n i s h d e p o s i t ) ,
r e m o v e t h e m a n d c l e a n t h e m .
A t t h e r i s k o f d i s c h a r g i n g t h e b a t -
t e r y , t h e d e a c t i v a t e d f u n c t i o n s c a n
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of
c e r t a i n f u n c t i o n s i n r e l a t i o n t o t h e l e v e l
o f c h a r g e r e m a i n i n g i n t h e b a t t e r y .
W h e n t h e v e h i c l e i s b e i n g d r i v e n , t h e
load reduction function temporarily
d e a c t i v a t e s c e r t a i n f u n c t i o n s , s u c h a s
t h e a i r c o n d i t i o n i n g , t h e " A I R W A V E "
s y s t e m s , t h e r e a r s c r e e n d e - i c i n g . . .
T h e d e a c t i v a t e d f u n c t i o n s a r e r e a c t i v a t -
ed automatically as soon as conditions
p e r m i t .
T o a v o i d d i s c h a r g i n g t h e b a t t e r y ,
d o n o t l e a v e t h e l i g h t s o n r e p e a t -
edly with the ignition off (refer to
t h e " E n e r g y e c o n o m y m o d e " p a r a -
g r a p h ) .
I t i s a d v i s a b l e t o d i s c o n n e c t t h e
b a t t e r y i f t h e v e h i c l e i s t o b e l e f t u n -
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
C l o s e t h e r o o f , t h e w i n d o w s a n d
the doors before disconnecting the
b a t t e r y .
Following reconnection of the
battery
F o l l o w i n g r e c o n n e c t i o n o f t h e b a t -
t e r y , s w i t c h o n t h e i g n i t i o n a n d w a i t
1 m i n u t e b e f o r e s t a r t i n g t o p e r m i t i n i -
t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
c o u n t e r e d f o l l o w i n g t h i s o p e r a t i o n ,
c o n t a c t a P E U G E O T d e a l e r .
R e f e r r i n g t o t h e c o r r e s p o n d i n g s e c -
t i o n , y o u m u s t y o u r s e l f r e i n i t i a l i s e :
- t h e r e m o t e c o n t r o l k e y ,
- t h e e l e c t r i c w i n d o w s a n d t h e
automatic partial opening of the
d o o r w i n d o w s ,
- t h e G P S s a t e l l i t e n a v i g a t i o n s y s t e m .
Page 163 of 294
10
!
!
i
148
PRACTICAL INFORMATION
Do not disconnect the terminals
w h i l e t h e e n g i n e i s r u n n i n g .
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
T h e b a t t e r i e s c o n t a i n h a r m f u l s u b -
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
m u s t n o t , i n a n y c i r c u m s t a n c e s , b e
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
a n d v e h i c l e b a t t e r i e s t o a s p e c i a l
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
F o l l o w t h e i n s t r u c t i o n s f o r u s e p r o -
v i d e d b y t h e m a n u f a c t u r e r o f t h e
c h a r g e r .
R e c o n n e c t s t a r t i n g w i t h t h e n e g a t i v e
t e r m i n a l ( - ) .
C h e c k t h a t t h e t e r m i n a l s a n d c o n n e c -
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
s u l p h a t e ( w h i t i s h o r g r e e n i s h d e p o s i t ) ,
r e m o v e t h e m a n d c l e a n t h e m .
A t t h e r i s k o f d i s c h a r g i n g t h e b a t -
t e r y , t h e d e a c t i v a t e d f u n c t i o n s c a n
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of
c e r t a i n f u n c t i o n s i n r e l a t i o n t o t h e l e v e l
o f c h a r g e r e m a i n i n g i n t h e b a t t e r y .
W h e n t h e v e h i c l e i s b e i n g d r i v e n , t h e
load reduction function temporarily
d e a c t i v a t e s c e r t a i n f u n c t i o n s , s u c h a s
t h e a i r c o n d i t i o n i n g , t h e " A I R W A V E "
s y s t e m s , t h e r e a r s c r e e n d e - i c i n g . . .
T h e d e a c t i v a t e d f u n c t i o n s a r e r e a c t i v a t -
ed automatically as soon as conditions
p e r m i t .
T o a v o i d d i s c h a r g i n g t h e b a t t e r y ,
d o n o t l e a v e t h e l i g h t s o n r e p e a t -
edly with the ignition off (refer to
t h e " E n e r g y e c o n o m y m o d e " p a r a -
g r a p h ) .
I t i s a d v i s a b l e t o d i s c o n n e c t t h e
b a t t e r y i f t h e v e h i c l e i s t o b e l e f t u n -
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
C l o s e t h e r o o f , t h e w i n d o w s a n d
the doors before disconnecting the
b a t t e r y .
Following reconnection of the
battery
F o l l o w i n g r e c o n n e c t i o n o f t h e b a t -
t e r y , s w i t c h o n t h e i g n i t i o n a n d w a i t
1 m i n u t e b e f o r e s t a r t i n g t o p e r m i t i n i -
t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
c o u n t e r e d f o l l o w i n g t h i s o p e r a t i o n ,
c o n t a c t a P E U G E O T d e a l e r .
R e f e r r i n g t o t h e c o r r e s p o n d i n g s e c -
t i o n , y o u m u s t y o u r s e l f r e i n i t i a l i s e :
- t h e r e m o t e c o n t r o l k e y ,
- t h e e l e c t r i c w i n d o w s a n d t h e
automatic partial opening of the
d o o r w i n d o w s ,
- t h e G P S s a t e l l i t e n a v i g a t i o n s y s t e m .